In this study, the goal is to optimize the process and to reduce the clogging tendency during the continuous casting process. The focus is on clogging when the refractory base material (RBM) in the SEN is in contact with the liquid steel. It is difficult or impossible to avoid non-metallic inclusions in the liquid steel, but by a selection of a good RBM in the SEN clogging can be reduced.   Different process steps were evaluated during the casting process in order to reduce the clogging tendency. First, the preheating of the SEN was studied. The results showed that the SEN can be decarburized during the preheating process. In addition, decarburization of SEN causes a larger risk for clogging. Two types of plasma coatings were implemented to protect the RBM, to prevent reactions with the RBM, and to reduce the clogging tendency. Calcium titanate (CaTiO3) mixed with yttria stabilized zirconia (YSZ) plasma coatings were tested in laboratory and pilot plant trials, for casting of aluminium-killed low-carbon steels. For casting of cerium alloyed stainless steels, YSZ plasma coatings were tested in laboratory, pilot plant and industrial trials. The results showed that the clogging tendency was reduced when implementing both coating materials.   It is also of importance to produce clean steel in order to reduce clogging. Therefore, the steel cleanliness in the tundish was studied experimentally. The result showed that inclusions originated from the slag, deoxidation products and tundish refractory and that they were present in the tundish as well as in the final steel product. / <p>QC 20170227</p> / VINNOVA

The purpose of this thesis has been to evaluate the use of a swirl blade in the uphill teeming process through plant trials. Two series of trials were carried out at Scana Steel Stavanger AS. In the trials a divergent entrance nozzle with a 62° outlet angle were used when casting duplex stainless steel on a base plate with two 6.2 tons ingots. All molds were burned onto the ingots; leading to problems with emptying the ingots from the molds and severe damages on the molds. To get a better insight during the casting and understand why the molds were burned onto the ingots; during the second series of trials one mold on each base plate were filmed in the beginning of the casting process. Evaluation of the castings indicated that splashing on the mold wall at an initial stage was one reason for the mold burned onto the ingot. Further, material samples were collected to evaluate the non-metallic inclusion composition and distribution with SEM when casting with a swirl blade compared to when casting without. The area percentage of the inclusions in the samples was 1% and 2% for samples casted with and without swirl blade respectively with d=2.8 mm. The inclusion size also varied for samples casted with and without swirl blade; 98% of the inclusions were in the size range of 0-10 μm when casted with and in the size range 0-20 μm when casted without swirl blade. / Syftet med denna uppsats har varit att utvärdera användningen av swirlblad i götgjutningsprocessen. Två serier med försök har utförts på Scana Steel Stavanger AS. I försöken användes en inloppssten med 62°-vinklat utlopp, där duplexa rostfria stål göts på stigplan med två 6,2 tons kokiller. Alla kokiller brände fast på göten, vilket ledde till svårigheter vid urtag av göten samt skador på kokillerna. För att få en bättre förståelse av varför kokillerna brände fast, filmades ett göt på vardera stigplan under den andra försöksserien. Utvärdering av försöken indikerar att en anledning till att kokillerna brände fast på göten var att det stänkte upp stål på kokillväggen i ett tidigt stadium. Vidare har materialprover samlats in för att utvärdera sammansättningen samt utspridningen av icke-metalliska inneslutningar i SEM då göt gjutits med swirlblad jämfört med utan. Area procenten i proverna var 1% och 2% då proverna gjutits med respektive utan swirlblad, med d=2.8 mm. Även storleken på inneslutningarna i prover som gjutits med och utan swirlblad skiljde sig åt, 98% av inneslutningarna var i storleksintervallet 0-10 μm för prover gjutna med swirlblad medan de som gjutits utan var i storleksintervallet 0-20 μm. / JK24053

In this study, the goal is to optimize the process and to reduce the clogging tendency during the continuous casting process. The focus is on clogging when the refractory base material (RBM) in the SEN is in contact with the liquid steel. It is difficult or impossible to avoid non-metallic inclusions in the liquid steel, but by a selection of a good RBM in the SEN clogging can be reduced.   Different process steps were evaluated during the casting process in order to reduce the clogging tendency. First, the preheating of the SEN was studied. The results showed that the SEN can be decarburized during the preheating process. In addition, decarburization of SEN causes a larger risk for clogging. Two types of plasma coatings were implemented to protect the RBM, to prevent reactions with the RBM, and to reduce the clogging tendency. Calcium titanate (CaTiO3) mixed with yttria stabilized zirconia (YSZ) plasma coatings were tested in laboratory and pilot plant trials, for casting of aluminium-killed low-carbon steels. For casting of cerium alloyed stainless steels, YSZ plasma coatings were tested in laboratory, pilot plant and industrial trials. The results showed that the clogging tendency was reduced when implementing both coating materials.   It is also of importance to produce clean steel in order to reduce clogging. Therefore, the steel cleanliness in the tundish was studied experimentally. The result showed that inclusions originated from the slag, deoxidation products and tundish refractory and that they were present in the tundish as well as in the final steel product. / VINNOVA