No description available.

The thesis deals with the surface modification of cotton fabric by low-pressure micro-wave plasma discharge. The main materials used for this experiment are cotton fabrics and hexamethyldisiloxane. The experiment itself is focused on the modification of cotton fabric to improve hydrophobic atributes. An argon process gas was used in the surface modification. The individual treated samples were operated with changes in process gas flow and the time during which the above-mentioned modifications was performed. Two methods were used to analyze the results of the experiment. The first one was aimed at determining changes in hydrophobic atributes in the form of wetta-bility in an unmodified sample compared to other modificated samples using the drop-let method. An electron microscope was used for the subsequent study of possible changes in surface topography. From the point of view of the examined results, the difference in hydrophobic properties was observed when using the droplet method to-gether with the change in the topography of the surface obtained on the electron mi-croscope in the cotton samples examined. The actual evaluation of individual methods points to the desirable changes in modified cotton compared to unmodified cotton. Further information regarding the results of the experiment, depending on the changes in individual parameters in the cotton treatment process using low pressure microwave plasma discharge, are presented in thesis.

No description available.

No description available.

No description available.

Background: Separation science is heavily reliant on materials to fulfill ever more complicated demands raised by other areas of science, notably the rapidly expanding molecular biosciences and environmental monitoring. The key to successful separations lies in a combination of physical properties and surface chemistry of stationary phases used in liquid chromatographic separation, and this thesis address both aspects of novel separation materials. Methods: The thesis accounts for several approaches taken during the course of my graduate studies, and the main approaches have been i) to test a wild-grown variety of published methods for surface treatment of fused silica capillaries, to ascertain firm attachment of polymeric monoliths to the wall of microcolumns prepared in silica conduits; ii) developing a novel porogen scheme for organic monoliths including polymeric porogens and macromonomers; iii) evaluating a mesoporous styrenic monolith for characterization of telomers intended for use in surface modification schemes and; iv) to critically assess the validity of a common shortcut used for estimating the porosity of monoliths prepared in microconduits; and finally v) employing plasma chemistry for activating and subsequently modifying the surface of rigid, monodisperse particles prepared from divinylbenzene. Results: The efforts accounted for above have resulted in i) better knowledge of the etching and functionalization parameters that determine attachment of organic monoliths prepared by radical polymerization to the surface of silica; ii) polar methacrylic monoliths with a designed macroporosity that approaches the desired "connected rod" macropore morphology; iii) estab¬lishing the usefulness of monoliths prepared via nitroxide mediated polymerization in gradient polymer elution chromatography; iv) proving that scanning electron microscopy images are of limited value for assessing the macroporous properties of organic monoliths, and that pore measurements on externally polymerized monolith cocktails do not represent the porous properties of the same cocktail polymerized in narrow confinements; and v) showing that plasma bromination can be used as an activation step for rigid divinylbenzene particles to act as grafting handles for epoxy-containing telomers, that can be attached in a sufficiently dense layer and converted into carboxylate cation exchange layer that allows protein separations in fully aqueous eluents.

La faible densité et les propriétés mécaniques remarquables des composites polymères en font des matériaux de choix pour remplacer les métaux. Cependant, leurs propriétés physicochimiques rendent leurs surfaces peu adhésives pour divers types de revêtements. Pour améliorer l’adhérence de revêtements métalliques sur des substrats de PEEK, et pour mieux comprendre les mécanismes de l’adhésion, les propriétés de surface du matériau ont été modifiées par des procédés physiques en voie sèche.D’une part, cette étude montre que les traitements par plasma oxydants (à basse pression, ou à pression atmosphérique) permettent d’améliorer la mouillabilité de la surface et l’adhérence de revêtements métalliques, par l’augmentation de la polarité de la surface, quantifiée par XPS. D’autre part, cette étude montre que l’ablation laser infrarouge à impulsion femtoseconde permet la gravure d’un motif dense, induisant de meilleures tenues mécaniques de l’assemblage. Enfin, cette étude montre que la modification de la chimie et de la topographie combinées améliore davantage ce potentiel d’adhérence.Le but de cette étude est d’ouvrir une voie vers un modèle décrivant les mécanismes de l’adhésion, influencés par la chimie de surface et la géométrie d’un motif, en s’appuyant sur un modèle mécanique permettant de décrire la dynamique des contraintes se propageant au travers de l’interface, en tenant compte des propriétés mécaniques des matériaux. / Thanks to their low densities and good mechanical properties, polymer composites are good candidates for metal alloys substitutes. However, their physicochemical properties limit their adhesion potential towards several types of coatings. In order to improve metallic thin films adhesion on PEEK substrates, and to better comprehend adhesion mechanisms, dry-phase methods have been used to alter the surface properties of the material.First, this study shows that oxidative plasma treatments (at low or at atmospheric pressure) improve the wettability and the practical adhesion of metallic coatings, by an increase of the polar component of the surface, as measured by XPS. Second, this study shows that dense patterns etched by an infrared femtosecond laser allow good practical adhesion of the metallic thin films on the substrate. Finally, this study shows that the modification of both surface chemistry and the surface topography at the same time further improves the practical adhesion of the metallic thin films.The goal of this study is to propose a route towards a model describing the combined influence of surface texture and chemistry, with the support of a mechanical model describing the dynamics of the stress dissipation through the interface while taking into account the mechanicals properties of the interfacial materials.

No description available.