No description available.

Mémoire numérisé par la Direction des bibliothèques de l'Université de Montréal.

Este estudo avaliou a influência da fototerapia a laser (FTL) na proliferação e diferenciação de células-tronco da polpa dentária humana (DPSCs; do inglês, Dental Pulp Stem Cells ) encapsuladas em carreador injetável e termoresponsivo (PL; Pluronic® F-127, Sigma-Aldrich, MO, EUA) com incorporação de proteína morfogenética óssea 4 recombinante humana (rhBMP4) (sistema PL/rhBMP4). O biomaterial foi caracterizado de acordo com seus perfis de embebição e dissolução, liberação de rhBMP4 e sua estrutura morfológica. DPSCs foram isoladas, caracterizadas e encapsuladas em PL para confirmar sua viabilidade e seu potencial de diferenciação (adipo e osteogênico) em comparação com células-tronco mesenquimais de medula óssea (BMMSCs; do inglês, Bone Marrow Mesenchymal Stem Cells). Quando encapsuladas no sistema PL/rhBMP4, DPSCs foram irradiadas com duas densidades de energia diferentes utilizando laser de diodo de fosfeto de índio-gálio-alumínio (InGaAlP), modos contínuo, pontual e em contato [660 nm, 0,028 cm2, 20 mW, 0,71 W/cm2, 3 J/cm2 (4 s) ou 5 J/cm2 (7 s)]. Os ensaios de PKH26 (do inglês, Red Fluorescent Cell Linker), CFU-F (do inglês, Coloning Forming Units - Fibroblastic), e MTT (do inglês, 3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyl-tetrazolium bromide)) foram utilizados para avaliar adesão/proliferação, diferenças na capacidade formadora de colônias e viabilidade das DPSCs (neste último caso sob estresse nutricional), respectivamente. Finalmente, a diferenciação odonto/osteogênica foi analisada por qRT-PCR e confirmada por ensaio de vermelho de alizarina. O biomaterial embebeu e dissolveu rapidamente; densa rede tubular e reticular com poros interconectados foi observada. DPSCs e BMMSCs apresentaram alta viabilidade celular quando encapsuladas em PL. Ambas as linhagens celulares tiveram êxito em se diferenciar em tecidos adiposo e ósseo. De acordo com o PKH26, DPSCs puderam aderir e proliferar no sistema PL/rhBMP4. DPSCs irradiadas encapsuladas tanto em PL como em PL/rhBMP4 formaram mais CFU-F que os controles não irradiados. Sob estresse nutricional, DPSCs semeadas no PL e irradiadas com 5 J/cm2 exibiram maior taxa de viabilidade celular em relação aos grupos não irradiados e irradiados com 3 J/cm2. Na presença de rhBMP4, os grupos irradiados tanto com 3 J/cm2 quanto com 5 J/cm2 apresentaram deposição mineral precoce quando comparados aos grupos não irradiados. Ainda, após 21 dias de diferenciação odonto/osteogênica, DPSCs irradiadas produziram maior quantidade de nódulos mineralizados. A irradiação com 5 J/cm2 levou ao aumento significativo da expressão de genes envolvidos na diferenciação odonto/osteogênica, como colágeno tipo I (COL1A1), osteocalcina (OCN), proteína da matriz dentinária 1 (DMP1), sialofosfoproteina dentinária (DSPP) e proteína heat shock 27 kDa (HSPB1). A associação entre rhBMP4 e FTL promove proliferação e diferenciação odonto/osteogênica de DPSCs acelerando e aumentando notavelmente a formação de tecido mineralizado, em especial quando a densidade de energia de 5 J/cm2 é aplicada. / This study evaluated the influence of laser phototherapy (LPT) on dental pulp stem cells (DPSCs) proliferation and differentiation upon encapsulation in an injectable and thermo-responsive cell carrier (PL; Pluronic® F-127, Sigma-Aldrich, MO, USA) loaded with human recombinant bone morphogenetic protein 4 (rhBMP4)(PL/rhBMP4 system). The biomaterial was characterized according to its swelling and dissolution profiles, release of rhBMP4 and morphological structure. DPSCs were isolated, characterized and encapsulated in PL to confirm their viability and multilineage differentiation potential (adipo and osteogenic) in comparison to bone marrow mesenchymal stem cells (BMMSCs). When encapsulated in the PL/rhBMP4 system, DPSCs were irradiated with two different energy densities using a continuous-wave indium-gallium-aluminum-phosphide (InGaAlP) diode laser [660 nm, 0.028 cm2, 20 mW, 0.71 W/cm2, 3 J/cm2 (4 s) or 5 J/cm2 (7 s)] in punctual and contact modes. The PKH26 (Red Fluorescent Cell Linker), the CFU-F (Coloning Forming Units - Fibroblastic), and the MTT [3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyl-tetrazolium bromide] assays were used to assess differences in cell adhesion/proliferation, colony forming units formation ability, and cell viability of DPSCs (in this case under nutritional stress), respectively. Then, alizarin red and qRT-PCR analyzes were used to evaluate odonto/osteogenic differentiation. The biomaterial swelled and dissolved rapidly; dense tubular and reticular network morphology with well-interconnected pores was observed. DPSCs and BMMSCs presented high cell viability when encapsulated in PL. Both cell lineages successfully differentiated into bone or adipose tissues. According to PKH26, DPSCs were able to adhere and proliferate in the PL/rhBMP4 system. Irradiated DPSCs encapsulated in either PL or PL/rhBMP4 system formed more CFU-F than non-irradiated controls. Under nutritional stress, DPSCs encapsulated in the hydrogels with no rhBMP4 and irradiated at 5 J/cm2 exhibited higher cell viability than the other groups. In the presence of rhBMP4, the groups irradiated both at 3 and 5 J/cm2 energy densities displayed earlier mineral deposition than the non-irradiated groups. Moreover, after 21 days of odonto/osteogenic differentiation, irradiated DPSCs produced greater nodule formation than the control groups. At the energy density of 5 J/cm2, there were significant upregulation of genes involved in odonto/osteoblast differentiation, such as type I collagen (COL1A1), osteocalcin (OCN), dentin matrix protein 1 (DMP1), dentin sialophosphoprotein (DSPP) and heat shock protein 27 kDa (HSPB1). The association between rhBMP4 and LPT promotes cell proliferation and odonto/osteogenic differentiation of DPSCs accelerating and increasing the formation of mineralized tissue, in particular when the energy density of 5 J/cm2 is applied.

Este estudo avaliou a influência da fototerapia a laser (FTL) na proliferação e diferenciação de células-tronco da polpa dentária humana (DPSCs; do inglês, Dental Pulp Stem Cells ) encapsuladas em carreador injetável e termoresponsivo (PL; Pluronic® F-127, Sigma-Aldrich, MO, EUA) com incorporação de proteína morfogenética óssea 4 recombinante humana (rhBMP4) (sistema PL/rhBMP4). O biomaterial foi caracterizado de acordo com seus perfis de embebição e dissolução, liberação de rhBMP4 e sua estrutura morfológica. DPSCs foram isoladas, caracterizadas e encapsuladas em PL para confirmar sua viabilidade e seu potencial de diferenciação (adipo e osteogênico) em comparação com células-tronco mesenquimais de medula óssea (BMMSCs; do inglês, Bone Marrow Mesenchymal Stem Cells). Quando encapsuladas no sistema PL/rhBMP4, DPSCs foram irradiadas com duas densidades de energia diferentes utilizando laser de diodo de fosfeto de índio-gálio-alumínio (InGaAlP), modos contínuo, pontual e em contato [660 nm, 0,028 cm2, 20 mW, 0,71 W/cm2, 3 J/cm2 (4 s) ou 5 J/cm2 (7 s)]. Os ensaios de PKH26 (do inglês, Red Fluorescent Cell Linker), CFU-F (do inglês, Coloning Forming Units - Fibroblastic), e MTT (do inglês, 3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyl-tetrazolium bromide)) foram utilizados para avaliar adesão/proliferação, diferenças na capacidade formadora de colônias e viabilidade das DPSCs (neste último caso sob estresse nutricional), respectivamente. Finalmente, a diferenciação odonto/osteogênica foi analisada por qRT-PCR e confirmada por ensaio de vermelho de alizarina. O biomaterial embebeu e dissolveu rapidamente; densa rede tubular e reticular com poros interconectados foi observada. DPSCs e BMMSCs apresentaram alta viabilidade celular quando encapsuladas em PL. Ambas as linhagens celulares tiveram êxito em se diferenciar em tecidos adiposo e ósseo. De acordo com o PKH26, DPSCs puderam aderir e proliferar no sistema PL/rhBMP4. DPSCs irradiadas encapsuladas tanto em PL como em PL/rhBMP4 formaram mais CFU-F que os controles não irradiados. Sob estresse nutricional, DPSCs semeadas no PL e irradiadas com 5 J/cm2 exibiram maior taxa de viabilidade celular em relação aos grupos não irradiados e irradiados com 3 J/cm2. Na presença de rhBMP4, os grupos irradiados tanto com 3 J/cm2 quanto com 5 J/cm2 apresentaram deposição mineral precoce quando comparados aos grupos não irradiados. Ainda, após 21 dias de diferenciação odonto/osteogênica, DPSCs irradiadas produziram maior quantidade de nódulos mineralizados. A irradiação com 5 J/cm2 levou ao aumento significativo da expressão de genes envolvidos na diferenciação odonto/osteogênica, como colágeno tipo I (COL1A1), osteocalcina (OCN), proteína da matriz dentinária 1 (DMP1), sialofosfoproteina dentinária (DSPP) e proteína heat shock 27 kDa (HSPB1). A associação entre rhBMP4 e FTL promove proliferação e diferenciação odonto/osteogênica de DPSCs acelerando e aumentando notavelmente a formação de tecido mineralizado, em especial quando a densidade de energia de 5 J/cm2 é aplicada. / This study evaluated the influence of laser phototherapy (LPT) on dental pulp stem cells (DPSCs) proliferation and differentiation upon encapsulation in an injectable and thermo-responsive cell carrier (PL; Pluronic® F-127, Sigma-Aldrich, MO, USA) loaded with human recombinant bone morphogenetic protein 4 (rhBMP4)(PL/rhBMP4 system). The biomaterial was characterized according to its swelling and dissolution profiles, release of rhBMP4 and morphological structure. DPSCs were isolated, characterized and encapsulated in PL to confirm their viability and multilineage differentiation potential (adipo and osteogenic) in comparison to bone marrow mesenchymal stem cells (BMMSCs). When encapsulated in the PL/rhBMP4 system, DPSCs were irradiated with two different energy densities using a continuous-wave indium-gallium-aluminum-phosphide (InGaAlP) diode laser [660 nm, 0.028 cm2, 20 mW, 0.71 W/cm2, 3 J/cm2 (4 s) or 5 J/cm2 (7 s)] in punctual and contact modes. The PKH26 (Red Fluorescent Cell Linker), the CFU-F (Coloning Forming Units - Fibroblastic), and the MTT [3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyl-tetrazolium bromide] assays were used to assess differences in cell adhesion/proliferation, colony forming units formation ability, and cell viability of DPSCs (in this case under nutritional stress), respectively. Then, alizarin red and qRT-PCR analyzes were used to evaluate odonto/osteogenic differentiation. The biomaterial swelled and dissolved rapidly; dense tubular and reticular network morphology with well-interconnected pores was observed. DPSCs and BMMSCs presented high cell viability when encapsulated in PL. Both cell lineages successfully differentiated into bone or adipose tissues. According to PKH26, DPSCs were able to adhere and proliferate in the PL/rhBMP4 system. Irradiated DPSCs encapsulated in either PL or PL/rhBMP4 system formed more CFU-F than non-irradiated controls. Under nutritional stress, DPSCs encapsulated in the hydrogels with no rhBMP4 and irradiated at 5 J/cm2 exhibited higher cell viability than the other groups. In the presence of rhBMP4, the groups irradiated both at 3 and 5 J/cm2 energy densities displayed earlier mineral deposition than the non-irradiated groups. Moreover, after 21 days of odonto/osteogenic differentiation, irradiated DPSCs produced greater nodule formation than the control groups. At the energy density of 5 J/cm2, there were significant upregulation of genes involved in odonto/osteoblast differentiation, such as type I collagen (COL1A1), osteocalcin (OCN), dentin matrix protein 1 (DMP1), dentin sialophosphoprotein (DSPP) and heat shock protein 27 kDa (HSPB1). The association between rhBMP4 and LPT promotes cell proliferation and odonto/osteogenic differentiation of DPSCs accelerating and increasing the formation of mineralized tissue, in particular when the energy density of 5 J/cm2 is applied.

Inkjet printing (jetting) technology, due to its high speed of operation and accuracy, is utilised in Additive Manufacturing (AM) of three dimensional parts. Commercially available AM processes that use jetting technology include three dimensional printing (3DP by Z-Corporation), Polyjet (by Objet), Multi Jet Modelling (MJM by 3D Systems) and three dimensional printing by Solidscape. Apart from 3D Printing by Z-corporation, all the other jetting based processes require a support material to successfully build a part. The support material provides a base to facilitate the removal of the part from the build platform and it helps manufacturing of cavities, holes and overhanging features. These support materials present challenges in terms of their removability and reusability. This research is therefore, aimed towards finding a support material composition that can be used with jetting based AM processes. The support material should be easily removable either by melting or by dissolution and also, if possible, it should be reusable. AM processes often process materials with poor mechanical properties and therefore, the parts produced by these processes have limited functionality. In an attempt to obtain complex shaped, functional parts made of nylon (i.e. Polyamide 6), a new jetting based AM process is under research at Loughborough University. The process uses two different mixtures of caprolactam (i.e. the monomer used to produce polyamide). These mixtures are to be jetted using inkjet heads and subsequently polymerised into polyamide 6. Therefore, another aim of this research was to consider the support material s suitability for jetting of caprolactam. Two different polymers were researched which included Pluronic F-127 and methylcellulose (MC). Both these polymers are known for gel formation upon heating in aqueous solutions. Due to the inhibition of polymerisation of polyamide 6 by the presence of water, non-aqueous solvents such as ethylene glycol, propylene glycol and butylene glycol were studied. Since both F-127 and MC in the glycols mentioned above had not been studied before, all the compositions prepared and investigated in this report were novel. F-127 did not show gel formation in propylene and butylene glycol but formed a gel in ethylene glycol at a concentration of 25% (w/w) F-127. MC, on the other hand, showed gel formation upon cooling in all the three glycols at concentrations as low as 5% for ethylene glycol and 1% for both propylene and butylene glycol. These compositions were characterized using experimental techniques such as Fourier Transform Infrared (FTIR) spectroscopy, hot stage microscopy, differential scanning calorimetry (DSC) and X-ray diffraction (XRD). A mechanism of gelation for both F-127 and MC in glycols is presented based on the results of these characterisation techniques. Viscosity and surface tension measurements along with the texture analysis of selected compositions were also performed to evaluate their suitability for jetting. All these compositions, due to their water solubility and/or low melting temperatures (i.e. near 500C) present the advantage of ease of removal. Removal by melting at low temperatures can also provide reusability of these support materials and thus advantages such as reduction in build cost and environmental effect can be achieved.

As all the physiological processes in our body are controlled by multiple biomolecules, comprehensive treatment of certain disease conditions may be more effectively achieved by administration of more than one type of drug. Thus, the primary objective of this research was to develop a multilayered, polymer-based system for sequential delivery of multiple drugs. This particular device was designed aimed at the treatment of periodontitis, a highly prevalent oral inflammatory disease that affects 90% of the world population. This condition is caused by bacterial biofilm on the teeth, resulting in a chronic inflammatory response that leads to loss of alveolar bone and, ultimately, the tooth. Current treatment methods for periodontitis address specific parts of the disease, with no individual treatment serving as a complete therapy. The polymers used for the fabrication of this multilayered device consists of cellulose acetate phthalate (CAP) complexed with Pluronic F-127 (P). After evaluating morphology of the resulting CAPP system, in vitro release of small molecule drugs and a model protein was studied from both single and multilayered devices. Drug release from single-layered CAPP films followed zero-order kinetics related to surface erosion property of the association polymer. Release studies from multilayered CAPP devices showed the possibility of achieving intermittent release of one type of drug as well as sequential release of more than one type of drug. Mathematical modeling accurately predicted the release profiles for both single layer and multilayered devices. After the initial characterization of the CAPP system, the device was specifically modified to achieve sequential release of drugs aimed at the treatment of periodontitis. The four types of drugs used were metronidazole, ketoprofen, doxycycline, and simvastatin to eliminate infection, inhibit inflammation, prevent tissue destruction, and aid bone regeneration, respectively. To obtain different erosion times and achieve appropriate release profiles specific to the disease condition, the device was modified by increasing the number of layers or by inclusion of a slower eroding polymer layer. In all the cases, the device was able to release the four different drugs in the designed temporal sequence. Analysis of antibiotic and anti-inflammatory bioactivity showed that drugs released from the devices retained 100% bioactivity. Following extensive studies on the in vitro sequential drug release from these devices, the in vivo drug release profiles were investigated. The CAPP devices with different release rates and dosage formulations were implanted in a rat calvarial onlay model, and the in vivo drug release and erosion was compared with in vitro results. In vivo studies showed sequential release of drugs comparable to those measured in vitro, with some difference in drug release rates observed. The present CAPP association polymer-based multilayer devices can be used for localized, sequential delivery of multiple drugs for the possible treatment of complex disease conditions, and perhaps for tissue engineering applications, that require delivery of more than one type of biomolecule.