A obtenção de blendas condutoras a base de água, ainda é pouco explorada e apresenta uma interessante alternativa ao uso de compostos poluentes como os cromatos na proteção à corrosão metálica. Os polímeros condutores apresentam propriedades anti-corrosivas e podem ser processados em meio aquoso, eliminando o uso de solventes orgânicos altamente tóxicos e agressivos para o meio ambiente. O presente trabalho consiste no estudo da proteção da corrosão metálica por revestimento de filmes de blendas contendo Poli(anilina) (PANI). As blendas foram obtidas à partir da mistura de uma suspensão aquosa de PANI com uma dispersão aquosa de Poli(metil metacrilato). O uso de técnicas como potencial zeta, espalhamento de luz dinâmico, análise térmica e microscopia eletrônica de varredura permitiram a caracterização da mistura homogênea obtida. Medidas através do método da sonda de quatro pontas mostraram que as blendas apresentam condutividade mesmo com baixas quantidades de PANI e a técnica de espectroscopia Raman mostrou a presença da forma condutora deste polímero nos filmes das blendas. Técnicas como microscopia óptica, potencial a circuito aberto, voltametria linear e espectroscopia de impedância eletroquímica permitiram avaliar a proteção à corrosão de eletrodos metálicos de ferro, cobre e níquel recobertos com filmes das blendas de PANI em diferentes meios corrosivos. As blendas mostraram eficiência contra a corrosão e apresentam-se como um novo material não poluente para a proteção à corrosão metálica. / The development of water-based conducting blends has not yet been very much explored and it presents itself as an interesting alternative to the use of polluting compounds such as chromates in the protection of metals from corrosion. The conducting polymers present anti-corrosion properties and can be processed in aqueous medium, eliminating the use of organic solvents, which are highly toxic and threatening to the environment. This thesis is based on the study of protection from metallic corrosion using poly(aniline) (PANI) coating blends. The blends have been obtained by mixing a PANI aqueous suspension with a poly(methyl metacrylate) aqueous dispersion. Techniques such as zeta potential, dynamic light scattering, thermal analysis and scanning electronic microscopy allowed the characterization of the homogeneous mixture obtained. Measurements carried out by the four-point probe method showed that the blends present conductivity even despite low PANI quantities. In addition, the Raman spectroscopy technique showed the presence of the conducting form of this polymer on the blend films. Techniques such as optical microscopy, open-circuit potential, linear voltammetry and impedance spectroscopy allowed the evaluation of the corrosion protection of the iron, copper, and nickel metallic electrodes coated with PANI blend films in different corrosives mediums. The blends showed efficiency against corrosion and they are therefore a new environmentally friendly material for metallic corrosion protection.

The interest in conjugated polymers has been two-fold. A rich variety of intriguing physical phenomena, combined with its immense technological implications in the area of molecular electronics, sensors etc. has inspired the researchers all over the globe. The work presented in this thesis is focussed on one of the most widely studied conjugated polymers, namely polyaniline (PANI), which is well known for its high conductivity and remarkable stability in the proton-doped form. The thesis is divided into two chapters and each chapter is further divided into several parts. In the first chapter, we take a look at some novel systems based on PANI that exhibit interesting electrical and optical properties. To begin with, we report the synthesis and characterization (Part I, Chapter 3) a new class of highly conducting polyaniline doped with electron deficient Lewis acids, namely the boron trihalides (BX3, X = F, Cl, and Br). We discuss the various attributes of this interesting class of materials that set it apart from the conventional proton-doped PANI systems. It is known that the conductivity in doped PANI is greatly influenced by the presence of structural disorder. Previous studies have associated the conductivity in doped PANI with the partial crystallinity that is achieved upon proton doping. At the same time, the amorphous regions that have a high degree of disorder were believed to suppress the metallic nature in these doped systems. In view of this "higher-crystallinity-higher-conductivity" picture, it is interesting to note that the BX3 doped PANI remain absolutely amorphous despite being more conducting than previously known samples. Through our investigation, we have been able to address some of the most important and long-standing questions pertaining to the nature of the charge carriers and the role of disorder in doped PANI. A detailed study of the transport properties in Part II, Chapter 3 helps us to understand the mechanism of charge transfer in these novel systems. With the help of our results, we establish that the present systems do not belong to the family of quasi one-dimensional conductors, in stark contrast to the conventional proton-doped samples. Instead, our systems are best described as granular metals, where the conduction mechanism is controlled by the size of the conducting grains and the nature of the grain boundaries. Through a comprehensive study of the magnetic properties based on d. c. magnetic susceptibility and EPR spectroscopy, we further establish that the intrinsic conductivity of these samples are much higher than the previously known systems. By studying the interaction of the mobile charge carriers and the localized spins in the systems, we have established that our samples are far less disordered, and therefore qualify as superior systems when compared to the more conventional proton-doped PANI. One of the serious disadvantages of the conventional protonated PANI lies in its thermal instability. On heating above 75 ±C in air, the polymer backbone undergoes an irreversible aerial oxidation that disrupts the extended conjugated structure. This is marked by a rapid drop in conductivity by a few orders of magnitude. BF3-doped PANI, which has the highest conductivity sample among the present series of samples, exhibits a remarkable thermal stability in air (Part III, Chapter 3). Upon heating, the conductivity initially increases and then reaches a saturation value. The polymer can be heated at temperatures as high as 225 ±C, without any signs of degradation. With the help of temperature dependent conductivity, XPS and FTIR spectroscopy we have tried to understand this unexpected phenomenon. In Part IV, Chapter 3, we report the synthesis and characterization of a novel class of functionalized PANI that exhibit an intense deep-blue photoluminescence. A de- tailed characterization based on absorption, photoluminescence, XPS, NMR and FTIR spectroscopy has been carried out to study the chemical state of this new class of light- emitting polymers. Further, we note that the synthetic procedure followed in this work can provide a very general route to the synthesis of diversely useful derivatives of PANI. In Chapter 4, we have investigated the microscopic origin of conductivity in doped PANI. Among the several factors that can influence the conductivity of doped polymers, one is the microstructural order. To understand this better, we carried out a detailed investigation, based on scanning tunneling microscopy (STM) and spectroscopy (STS) of undoped and doped PANI films (Part I, Chapter 4). We have shown for the ¯rst time that solution processed thin films of undoped PANI has an abundance of PANI anorods self organized over very large areas. Further, we observe that this ordered orphology is Preface vii very sensitive to the choice of dopants and the doping procedure. We have shown that the morphological order can greatly influence the electronic structure and therefore the properties of these systems. To understand the role of dopant-polymer interaction in controlling the conductivity of doped PANI, we carried out x-ray photoelectron spectroscopy (XPS) studies on a large number of partially and fully doped samples (Part II, Chapter 4). We find an interesting trend in the higher binding energy feature and the asymmetry of the N and C 1s spectra, which correlates directly with the respective conductivities of different samples. The analysis of these spectra brings out interesting facts about the chemical state and the electronic structure of these samples. In summary, we have reported new PANI based systems with improved electrical and interesting optical properties, and have studied various factors that influence the properties of these as well as some of conventional doped PANI systems.

A obtenção de blendas condutoras a base de água, ainda é pouco explorada e apresenta uma interessante alternativa ao uso de compostos poluentes como os cromatos na proteção à corrosão metálica. Os polímeros condutores apresentam propriedades anti-corrosivas e podem ser processados em meio aquoso, eliminando o uso de solventes orgânicos altamente tóxicos e agressivos para o meio ambiente. O presente trabalho consiste no estudo da proteção da corrosão metálica por revestimento de filmes de blendas contendo Poli(anilina) (PANI). As blendas foram obtidas à partir da mistura de uma suspensão aquosa de PANI com uma dispersão aquosa de Poli(metil metacrilato). O uso de técnicas como potencial zeta, espalhamento de luz dinâmico, análise térmica e microscopia eletrônica de varredura permitiram a caracterização da mistura homogênea obtida. Medidas através do método da sonda de quatro pontas mostraram que as blendas apresentam condutividade mesmo com baixas quantidades de PANI e a técnica de espectroscopia Raman mostrou a presença da forma condutora deste polímero nos filmes das blendas. Técnicas como microscopia óptica, potencial a circuito aberto, voltametria linear e espectroscopia de impedância eletroquímica permitiram avaliar a proteção à corrosão de eletrodos metálicos de ferro, cobre e níquel recobertos com filmes das blendas de PANI em diferentes meios corrosivos. As blendas mostraram eficiência contra a corrosão e apresentam-se como um novo material não poluente para a proteção à corrosão metálica. / The development of water-based conducting blends has not yet been very much explored and it presents itself as an interesting alternative to the use of polluting compounds such as chromates in the protection of metals from corrosion. The conducting polymers present anti-corrosion properties and can be processed in aqueous medium, eliminating the use of organic solvents, which are highly toxic and threatening to the environment. This thesis is based on the study of protection from metallic corrosion using poly(aniline) (PANI) coating blends. The blends have been obtained by mixing a PANI aqueous suspension with a poly(methyl metacrylate) aqueous dispersion. Techniques such as zeta potential, dynamic light scattering, thermal analysis and scanning electronic microscopy allowed the characterization of the homogeneous mixture obtained. Measurements carried out by the four-point probe method showed that the blends present conductivity even despite low PANI quantities. In addition, the Raman spectroscopy technique showed the presence of the conducting form of this polymer on the blend films. Techniques such as optical microscopy, open-circuit potential, linear voltammetry and impedance spectroscopy allowed the evaluation of the corrosion protection of the iron, copper, and nickel metallic electrodes coated with PANI blend films in different corrosives mediums. The blends showed efficiency against corrosion and they are therefore a new environmentally friendly material for metallic corrosion protection.

Following the discovery of electronic conductivity in doped polyacetylene, various studies on conducting polymers have been investigated. These polymers are essentially characterized by the presence of conjugated bonding on polymer backbone, which facilitates formation of polarons and bipolarons as charge carriers. Poly(3,4-ethylenedioxythiophene) (PEDOT) is an interesting polymer because of high electronic conductivity, ease of synthesis and high chemical stability. Electrochemically prepared PEDOT is more interesting than the polymer prepared by chemical routes because it adheres to the electrodes surface and the PEDOT coated electrodes can directly be used for various applications such as batteries, supercapacitor, sensors, etc. A majority of the studies described in the thesis are based on PEDOT. Studies on polyanthanilic acid and reduction of hydrogen peroxide on stainless steel substrate are also included. Chapter 1 provides an introduction to conducting polymers with a focus on synthesis, electrochemical characterization and applications of PEDOT. In Chapter 2, microscopic and impedance spectroscopic characterization of PEDOT coated on stainless steel (SS) and indium tin oxide (ITO) coated glass substrates are described. Electrosynthesis of PEDOT is carried out on SS electrodes by three different techniques, namely, potentiostatic, galvanostatic and potentiodynamic techniques. The SEM images of PEDOT prepared by the galvanostatatic and potentiostatic routes indicate globular morphology. However, it is seen that porosity increases by increasing the current or the potential. In the cases of both galvanostatic and potentiostatic routes, the oxidation of EDOT to form PEDOT takes place continuously during preparation. However, in the case of potentiodynamic experiment between 0 and 0.9 V vs. SCE (saturated calomel electrode), the formation of PEDOT occurs only when the potential is greater than 0.70 V. During multicycle preparation to grow thicker films of PEDOT, formation of PEDOT takes place layer by layer, a layer of PEDOT being formed in each potential cycle. PEDOT prepared in the potential ranges 0-0.90 V and 0-1.0 V show globular morphology similar to the morphology of the galvanostatically and potentiostatically prepared polymer. If prepared in the potential ranges 0-1.1 V and 0-1.2 V, the PEDOT films have rod-like and fibrous morphology. This is attributed to larger amount of PEDOT formed in each cycle in comparison with lower potential ranges and also to partial oxidation of PEDOT at potentials ≥ 1.10 V. PEDOT is also electrochemically prepared on ITO coated glass substrate. Preparation is carried out under potentiostatic conditions in the potential range between 0.9 and 1.2 V. Atomic force microscopy (AFM) studies indicate a globular topography for PEDOT films prepared on ITO coated glass plates. The height and width of globules increase with an increase in deposition potential. The PEDOT coated SS electrodes are subjected to electrochemical impedance spectroscopy studies in 0.1 M H2SO4. The Nyquist plot of impedance consists of a depressed semicircle, which arises due to a parallel combination of the polymer resistance and double-layer capacitance (Cdl). Impedance data are analyzed. Studies on electrooxidation of methanol, formic acid, formaldehyde and ethanol on nanocluster of Pt and Pt-Ru deposited on PEDOT/C electrode are reported in Chapter 3. Studies on electrooxidation of small molecules are important in view of their promising applications in fuel cells. Films of PEDOT are electrochemically deposited on carbon paper. Nanoclusters of Pt and bimetallic Pt-Ru catalysts are potentiostatically deposited on PEDOT/C electrodes. Catalysts are also prepared on bare carbon paper for studying the effect of PEDOT. The presence of PEDOT film on carbon paper allows the formation of uniform, well dispersed nanoclusters of Pt as well as Pt-Ru catalysts. TEM studies suggest that the nanoclusters of about 50 nm consist of nanoparticles of about 5 nm in diameter. Electrooxidation of methanol, formic acid, formaldehyde and ethanol are studied on Pt-PEDOT/C and PtRu-PEDOT/C electrodes by cyclic voltammetry and chronoamperometry. The data for oxidation of these small organic molecules reveal that PEDOT imparts a greater catalytic activity for the Pt and Pt-Ru catalysts. Results of these studies are described in Chapter 3. In Chapter 4, PEDOT is coated on SS substrate to investigate phenol oxidation. Studies on electrochemical oxidation of phenol are interesting because it is important to remove phenol from contaminated water or industrial effluents. Deactivation of the anode due to the formation and adsorption of polyoxyphenylene on its surface is a common problem for a variety of electrode materials, during phenol oxidation. Investigations on suitable anode materials, which can undergo no or moderate poisoning by polyoxyphenylene, are interesting. In the present study, it is shown that the electrooxidation rate of phenol is greater on PEDOT/SS electrodes than on Pt. Deactivation of PEDOT/SS electrode is slower in relation to Pt. The oxidation of phenol on PEDOT/SS electrode occurs to form both polyoxyphenylene and benzoquinone in parallel. Cyclic voltammetry of phenol oxidation is studied by varying the concentration of phenol, sweep rate and thickness of PEDOT. Ac impedance studies indicate a gradual increase in polymer resistance due to adsorption of polyoxyphenylene during multi sweep cyclic voltammetry. This investigation reveals that PEDOT coated on a common metal or alloy such as SS is useful for studying electrooxidation of phenol, which is generally studied on a noble metal based electrodes. Electrochemically prepared PEDOT is used for supercapacitor studies and the results are presented in Chapter 5. Generally, electronically conducting polymers possess high capacitive properties due to pseudo-faradaic reactions. PEDOT/SS electrodes prepared in 0.1 M H2SO4 are found to yield higher specific capacitance (SC) than the electrodes prepared from neutral aqueous electrolyte. The effects of concentration of H2SO4, concentration of SDS, potential of deposition and nature of supporting electrolytes used for capacitor studies on SC of the PEDOT/SS electrodes are studied. Specific capacitance values as high as 250 F g-1 in 1 M oxalic acid are obtained during the initial stages of cycling. However, there is a decrease in SC on repeated charge-discharge cycling. Spectroscopic data reflect structural changes in PEDOT on extended cycling. Self-doped PANI is expected to possess superior electrochemical characteristics in relation to PANI. The self-doping is due to the presence of an acidic group on the polymer chain. However, self-doped PANI is soluble in acidic solutions against insolubility of PANI. In the present study, poly(anthranilic acid), PANA, is encapsulated in porous Nafion membrane by chemical and a novel electrochemical methods. PANA present in solid form in Nafion membrane does not undergo dissolution in acidic solutions. The methods of preparation and various electrochemical, optical and spectroscopic characterizations studies of PANA-Nafion are described in Chapter 6. Electroreduction of H2O2 is studied on sand-blasted stainless steel (SSS) electrode in an aqueous solution of NaClO4 and the details are reported in Chapter 7. The cyclic voltammetric reduction of H2O2 at low concentrations is characterized by a cathodic peak at -0.40 V versus standard calomel electrode (SCE). Cyclic voltammetry is studied by varying the concentration of H2O2 in the range from 0.2 mM to 20 mM and the sweep rate in the range from 2 to 100 mV s-1. Cyclic voltammograms at concentrations of H2O2 higher than 2 mM or at high sweep rates consist of an additional current peak, which may be due to the reduction of adsorbed species formed during the reduction of H2O2. Amperometric determination of H2O2 at -0.50 V vs. SCE provides the detection limit of 5 μM H2O2. A plot of current density versus concentration has two linear segments suggesting a change in the mechanism of H2O2 reduction at concentrations of H2O2 ≥ 2 mM. From the rotating disc electrode study, diffusion co-efficient of H2O2 and rate constant for reduction of H2O2 are evaluated. Thus, stainless steel, which is inexpensive and a common alloy, is useful for studying electrochemical reduction of H2O2 and also for analytical application. This work is initiated to study the reduction of H2O2 on PEDOT/SS electrodes. As a result of preliminary experiments, it is found that PEDOT does not exhibit any influence on the kinetics of H2O2 reduction. Therefore studies conducted using bare stainless steel are included in this chapter. Results of the above studies are described in the thesis.

The studies reported in the thesis deal with surface modification of non-platinum metals by coating with electronically conducting polymers, namely, polyanilne (PANI) and polypyrrole (PPY). The oxidation of Г/I2, hydroquinone/quinine and [Fe(CN)6]3-/ [ Fe(CN)6]4-are studied by cyclic voltammetry and chronoamperometry experiments. It has been shown tht the redox reactions, which do not occur on bare stainless steel electrode, occur through electron-transfer mediated by conducting polymers. The effect of heating of polyaniline (PANI) at 80 0C on its electrochemical activity is studies. Although the thermogravimetric analysis indicates that PANI is stable at temperatures up to about 250 0C and it undergoes decomposition at higher temperatures, its intrinsic redox electrochemical activity decreases with duration of heating at a temperature as low as 80 0C . The polymer completely loses its electrochemical activity. The decrease in lectrochemical activity of PANI is attributed to an irreversible loss of water molecules. The reaction order for degradation of PANI is found to be close to unity, and a value of 1.63 X 10-4 s-1 is obtained for the rate constant. The deactivated PANI does not recover its electrochemical activity even after a prolonged treatment in acidic electrolytes. The electrodeposition of PANI is carried out by galvanostatic, potentiostatic and potentiodynamic methods. The impedance data reflect a marked difference between the PANI deposited by static and dynamic methods. Furthermore, the impedance parameters vary with the sweep rate used in potentiodynamic method. Electrochemical impedance spectra of the electrodes are analyzed using a transmission line model consisting of two rails of finite resistances. Electrochemical deposition of polyaniline (PANI) is carried out on a porous carbon substrate for supercapacitor studies. PANI deposited at 100 mV s-1 sweep rate by potentiodynamic technique on porous carbon substrate is found to possess superior capacitance properties. Capacitance values as high as 1600 F g-1 are obtained and PANI coated carbon electrodes facilitate charge-discharge current densities as hgh as 45 mA cm-2 (19.8 A g-1 ). Electrodes are found to be fairly stable over a long cycle-life, although there is some capacitance loss during the initial stages of cycling. Electrooxidation of ascorbic acid on polyaniline is studied in a fuel-cell. Ascorbic acid (H2A) is employed as fuel and polyaniline (PANI) as the catalyst. H2A is an environmentally and biologically friendly molecule. The catalyst, namely PANI does not consist of any platinum group metal, and at 70 0C , a maximum power density of 4.3 mW cm-2 is obtained at a current density of 15 mA cm-2 . Also, studies on anodically deposited RuO2 for capacitor applications are reported. Cathodic deposition of RuO2 generally produces a mixture of Ru and RuO2 . On the other hand, the anodic depsotion on SS substrates is found to produce RUO2 which is characterized with high power supercapacitance properties. A capacitance value of 274 F g-1 is obtained at a current density of 20mA cm-2 .

The present thesis is focused on the synthesis and environmental applications of polyaniline and its nanocomposites. It is organized in six chapters and brief discussions of the contents of the individual chapters are given below. Chapter 1 reviews two important water purification methods: adsorption and photocatalysis, which are widely discussed in literature. A general introduction to conducting polymers has been given and their photocatalytic activity has been described. Chapter 2 reports the application of polyaniline emeraldine salt for the removal of anionic dyes from aqueous solutions by adsorption. A possible mechanism for the anionic dye adsorption by PANI emeraldine salt has been proposed. The electrostatic interaction between the positively charged PANI backbone and dye anions is responsible for significant dye adsorption. The kinetic parameters for the adsorption of anionic dyes on PANI have also been determined. In Chapter 3, we investigate the adsorption and desorption of anionic dyes from aqueous solution by PANI doped with different protonic acids. PANI with three dopants, namely p-toluene sulfonic acid (PTSA), camphor sulfonic acid (CSA) and dodecyl benzene sulfonic acid (DBSA) were used to adsorb various dyes. The adsorbed dyes were desorbed from the polymer by using a basic aqueous solution. It was found that the adsorption of dye is dependent on the size and nature of the dopant acids. The influence of different dopants on the adsorption and desorption kinetic parameters was also examined. In chapter 4, the inherent property of PANI to adsorb dyes has been explored for the detection of dyes by electrochemical method. The changes in the CV of PANI film coated on Pt electrodes on addition of dye have been employed for detection of dye in aqueous solution. Furthermore, PANI coated stainless steel (SS) electrodes show a change in current intensity of Fe2+/Fe3+ redox peaks due to addition of dye in the electrolyte solution. Chapter 5 describes the synthesis and characterization of polyaniline-grafted-chitosan (CPANI) with different grafting ratios. The mechanical properties and the crystallinity of CPANI were investigated by means of nanoindentation and X-ray diffraction experiments, respectively. CPANI has been further self-assembled into multilayer thin film via versatile and simple layer-by-layer (LbL) approach. Negatively charged hyaluronic acid (HUA) was used as complementary polyelectrolyte for the self-assembly. LbL growth of the multilayer thin films has been monitored with UV-vis spectral analysis as well as by AFM. The formation of thin film has been further characterized by SEM. The pH responsive behavior of CPANI/HUA multilayer thin film has been investigated. Reusability of this thin film has been investigated by repeating the pH responsive experiments for 10 cycles. Chapter 6 is focused on the preparation of nanocomposite thin films of CPANI/PSS/TiO2 via LbL approach. LbL growth of this self-assembly was monitored by UV-vis spectral analysis and porous nature was observed from SEM images. Poly (styrene sulfonate) (PSS) was used as bridging layer between TiO2 nanoparticles and CPANI for the multilayer self-assembly. Incorporation of CPANI within this LbL self-assembly enhanced the dye degradation ability of the thin film by increasing the availability of dye molecules around the TiO2 nanoparticles. Furthermore, CPANI may act as a sensitizer to enhance the photocatalytic activity of TiO2. The effects of surface area of the multilayer thin film and amount of catalysts (TiO2 nanoparticles) incorporated in the self-assembly were described based on the kinetics of the dye degradation reactions. The same multilayer thin film can be efficiently used for dye degradation several times. The work presented in this thesis utilizes unique dye adsorption properties of PANI and its copolymers. The change in conductivity of PANI after dye adsorption and the electrochemical dye detection in aqueous medium promise the potential of PANI as a dye sensing material in waste water at very low concentration. The nanocomposites of CPANI/PSS/TiO2 present a novel material for photocatalysis.

Magister Scientiae - MSc (Chemistry) / Blending polymers together offers researchers the ability to create novel materials that have a combination of desired properties of the individual polymers for a variety of functions as well as improving specific properties. The behaviour of the resulting blended polymer or blend is determined by the interactions between the two polymers. The resultant synergy from blending an intrinsically conducting polymer like polyaniline (PANI), is that it possesses the electrical, electronic, magnetic and optical properties of a metal while retaining the poor mechanical properties, solubility and processibility commonly associated with a conventional polymer. Aromatic polyamic acid has outstanding thermal, mechanical, electrical, and solvent resistance properties that can overcome the poor mechanical properties and instability of the conventional conducting polymers, such as polyaniline.

Capacitive deionization is a promising technology for purification and desalination of brackish water with great advantages over current technologies due to its low operating cost and high-water recovery ratio. Most of the system studied relies on the adsorption/desorption capacity of activated carbon electrodes due to its high surface area. However, its specific adsorption capacity is limited since the adsorption is predominantly on the surface of the electrodes. In this thesis we propose the use of polyaniline as a chloride-ion adsorption material. Polyaniline is a redox polymer able to accommodate anions in several of its three states when subjected to an external voltage. To this end, we synthesized polyaniline by electrodeposition technique and its electrochemical behavior was studied. A hybrid CDI system was assembled, using PANI as anode material and activated carbon cloth as cathode, showing outstanding adsorption of 37.26 mg/g Cl at current densities of 250 A/g. The energy consumption of this system was of 0.4979 kWh/m3. Its stability was evaluated over 50 cycles with negligible capacity loss. Along with its use in a CDI system, the aim of this thesis was to understand the mechanisms of operation of this material, by means of its physical and electrochemical characterization, as well as its efficiency and stability through the use of this material in capacitive deionization cells. / Kapacitiv avjonisering är en lovande teknik för rening och avsaltning av bräckt vatten med stora fördelar jämfört med nuvarande teknik på grund av dess låga driftskostnader och höga vattenåtervinningsgrad. De flesta av de studerade systemen bygger på adsorptions/desorptionskapaciteten hos elektroder av aktivt kol på grund av dess stora yta. Dess specifika adsorptionskapacitet är dock begränsad eftersom adsorptionen huvudsakligen sker på elektrodernas yta. I den här avhandlingen föreslår vi att polyanilin används som adsorptionsmaterial för kloridjoner. Polyanilin är en redoxpolymer som kan ta emot anjoner i flera av sina tre tillstånd när den utsätts för en extern spänning. För detta ändamål syntetiserade vi polyanilin genom elektrodepositionsteknik och dess elektrokemiska beteende studerades. Ett hybrid CDI-system monterades med PANI som anodmaterial och aktiverad kolduk som katod, vilket visade en enastående adsorption av 37,26 mg/g Cl vid en strömtäthet på 250 A/g. Energiförbrukningen för detta system var 0,4979 kWh/m3. Systemets stabilitet utvärderades över 50 cykler med försumbar kapacitetsförlust. Förutom användningen i ett CDI-system var syftet med denna avhandling att förstå detta materials funktionsmekanismer genom fysisk och elektrokemisk karakterisering samt dess effektivitet och stabilitet genom användning av detta material i kapacitiva avjoniseringsceller.