Dans le contexte actuel d’une demande énergétique croissante associée à un appauvrissement des ressources fossiles, il devient urgent de trouver des sources d’énergies alternatives, écologiquement et économiquement viables. La photocatalyse est une voie prometteuse et innovante pour produire de l’hydrogène (H2) à partir d’énergies renouvelables. Le but est de développer des matériaux stables et efficaces pour amener le procédé à un niveau de maturité suffisant pour de possibles développements à moyen terme.Cette thèse est axée sur l’élaboration et l’optimisation de nouveaux systèmes composites nanostructurés, Au / gC3N4 / TiO2, pour la production d’hydrogène par procédé photocatalytique à partir de l’eau et de l’énergie solaire. L’aspect innovant étant d’optimiser chaque composant de manière à tirer profit des avantages de chacun, puis à surmonter leurs limitations individuelles en les associant de manière intime dans des structure hiérarchisées afin d’obtenir des taux de production d’H2 compétitifs à température ambiante sous illumination solaire et visible. Une étude comparative a également été entreprise sur le photocatalyseur commercial TiO2 P25 « Evonik ® » et met en avant l’efficacité de ces nouveaux matériaux. Pour finir, les activités photocatalytiques de ces composites ont ensuite été corrélées avec leurs propriétés physico-chimiques. / Nowadays, energy demand is constantly increasing while fossil ressources are dwindling and has become imperative to find new alternative energy sources. Photocatalysis is a promising and innovative way to produce hydrogen (H2) from renewable energies. The ai mis to develop stable and efficient materials in order to bring the process towards sufficient efficiency for possible mid-term developments. This thesis focuses on the development and optimization of new nanostructured composite systems, Au / gC3N4 / TiO2, for hydrogen produciton by water-splitting. The innovative aspect is to optimize every components in order to take advantages of each and then to intimately associate them in hierarchical structure for obtaining competitive rates of hydrogen production at room temperature under solar and visible illumination. A comparative study was also undertaken on commercial photocatalyst TiO2 P25 « Evonik ® » to highlight the efficiency of these new materials. Finally, photocatalytic activities of these composites were correlated with their physico-chemical properties.

La double fonction absorption-photodégradation des composites CA-TiO2 vis-à-vis des polluants biorécalcitrants est une alternative prometteuse pour le traitement de l’eau par voie solaire. Dans ce travail, des composites CA-TiO2 sont élaborés suivants trois méthodes simples basées sur l’utilisation des biomasses trouvées dans la sous région ensoleillée de l’Afrique subsaharienne. Les charbons actifs (CA) obtenus après pyrolyse des biomasses développent une structure poreuse qui se modifie ensuite en fonction de la voie de fixation des nanoparticules TiO2 (NPs-TiO2) pour l’obtention des composites. Parmi les trois vois de fixation du TiO2, l’imprégnation du CA avec le sol de NPs-TiO2 préformées conduit à des matériaux (CAT.SX) avec du TiO2 déposé de façon homogène à la « surface externe » du CA. Cette microtexture permet un meilleur couplage des propriétés adsorption-photodégradation, favorables aux performances de dépollution évaluées à l’échelle de laboratoire sur des solutions de phénol à 100 mg.L-1. Le réseau pores/surface spécifique est moins développé sur les composites obtenus par fixation in situ des NPs-TiO2 sur du CA imprégné de gel de TiO2 (CAT.GX), ou par pyrolyse directe de biomasse pré-imprégnée de NPs-TiO2 (CAT.SBX) ; ce qui explique les performances de dépollution moins élevées enregistrées pour ces deux dernières familles de catalyseurs. Les cinétiques d’élimination du polluant obtenues après plusieurs cycles successifs d’utilisation des catalyseurs CAT.SX ont été correctement simulées avec un modèle dont le formalisme tient compte de la double fonctionnalité des catalyseurs. Ce modèle permet d’envisager le dimensionnement d’installations solaires en condition réelle d’utilisation de ces nouveaux catalyseurs en zones fortement ensoleillée / Adsorption/photodegradation dual property of AC-TiO2 composites materials towards biorefractory pollutants is a promising issue for solar water treatment. In this work, AC-TiO2 hybrid materials have been synthesized through 03 novel routes based on the conversion of typical biomasses, abundantly found in the subsaharian African sunny areas. Biomasses pyrolysis derived activated carbon (AC) developed a porous structure which is modified differently according to the method used to fix TiO2 nanoparticules (TiO2-NPs). AC impregnated with a sol containing TiO2-NPs suspension provides the derived composite material (CAT.SX) with TiO2-NPs regularly deposited at the “external surface”, leading to a good coupling of adsorption/photodegradation activities towards phenol elimination in 100 mg.L-1 polluted water, carried out on lab scale experiments. Pore/surface area network is less developed on composites obtained after in situ fixation of TiO2-NPs on TiO2 gel impregnated AC (CAT.GX), or obtained after direct pyrolysis of TiO2-NPs impregnated biomass (CAT.SBX) – which infers lesser decontamination performances for these two latter families of catalysts. Pollutant elimination kinetics curves depicted after recycling of CAT.SX over several running water treatment was simulated with a suitable mathematical model which takes into consideration the dual functionalities of the elaborated material. The established model is a promising attempt for future dimensioning of real solar water treatment plants, operating in sunny areas with the new composite catalysts.

The present thesis is focused on the synthesis and environmental applications of polyaniline and its nanocomposites. It is organized in six chapters and brief discussions of the contents of the individual chapters are given below. Chapter 1 reviews two important water purification methods: adsorption and photocatalysis, which are widely discussed in literature. A general introduction to conducting polymers has been given and their photocatalytic activity has been described. Chapter 2 reports the application of polyaniline emeraldine salt for the removal of anionic dyes from aqueous solutions by adsorption. A possible mechanism for the anionic dye adsorption by PANI emeraldine salt has been proposed. The electrostatic interaction between the positively charged PANI backbone and dye anions is responsible for significant dye adsorption. The kinetic parameters for the adsorption of anionic dyes on PANI have also been determined. In Chapter 3, we investigate the adsorption and desorption of anionic dyes from aqueous solution by PANI doped with different protonic acids. PANI with three dopants, namely p-toluene sulfonic acid (PTSA), camphor sulfonic acid (CSA) and dodecyl benzene sulfonic acid (DBSA) were used to adsorb various dyes. The adsorbed dyes were desorbed from the polymer by using a basic aqueous solution. It was found that the adsorption of dye is dependent on the size and nature of the dopant acids. The influence of different dopants on the adsorption and desorption kinetic parameters was also examined. In chapter 4, the inherent property of PANI to adsorb dyes has been explored for the detection of dyes by electrochemical method. The changes in the CV of PANI film coated on Pt electrodes on addition of dye have been employed for detection of dye in aqueous solution. Furthermore, PANI coated stainless steel (SS) electrodes show a change in current intensity of Fe2+/Fe3+ redox peaks due to addition of dye in the electrolyte solution. Chapter 5 describes the synthesis and characterization of polyaniline-grafted-chitosan (CPANI) with different grafting ratios. The mechanical properties and the crystallinity of CPANI were investigated by means of nanoindentation and X-ray diffraction experiments, respectively. CPANI has been further self-assembled into multilayer thin film via versatile and simple layer-by-layer (LbL) approach. Negatively charged hyaluronic acid (HUA) was used as complementary polyelectrolyte for the self-assembly. LbL growth of the multilayer thin films has been monitored with UV-vis spectral analysis as well as by AFM. The formation of thin film has been further characterized by SEM. The pH responsive behavior of CPANI/HUA multilayer thin film has been investigated. Reusability of this thin film has been investigated by repeating the pH responsive experiments for 10 cycles. Chapter 6 is focused on the preparation of nanocomposite thin films of CPANI/PSS/TiO2 via LbL approach. LbL growth of this self-assembly was monitored by UV-vis spectral analysis and porous nature was observed from SEM images. Poly (styrene sulfonate) (PSS) was used as bridging layer between TiO2 nanoparticles and CPANI for the multilayer self-assembly. Incorporation of CPANI within this LbL self-assembly enhanced the dye degradation ability of the thin film by increasing the availability of dye molecules around the TiO2 nanoparticles. Furthermore, CPANI may act as a sensitizer to enhance the photocatalytic activity of TiO2. The effects of surface area of the multilayer thin film and amount of catalysts (TiO2 nanoparticles) incorporated in the self-assembly were described based on the kinetics of the dye degradation reactions. The same multilayer thin film can be efficiently used for dye degradation several times. The work presented in this thesis utilizes unique dye adsorption properties of PANI and its copolymers. The change in conductivity of PANI after dye adsorption and the electrochemical dye detection in aqueous medium promise the potential of PANI as a dye sensing material in waste water at very low concentration. The nanocomposites of CPANI/PSS/TiO2 present a novel material for photocatalysis.