This thesis is concerned with the synthesis of diazo compounds for the introduction of various functional groups on the surface of polymers by means of carbene insertion and diazonium coupling. Characterisation and investigation of their properties were conducted. A library of functionalised polystyrene beads containing pyridine rings has been established for the coordination of metal ions and metal complexes. The pyridyl system on the surface has demonstrated its capability to bind with zinc complexes of bis(thiosemicarbazones) and release the corresponding copper complexes upon transmetallation. A spiropyran derivative has been introduced onto the surface of polystyrene and polyethylene terephthalate. The chromophore on both polymers exhibited photoswitchability as determined from colour change and wettability. Polystyrenes with either pyridine or spiropyran units have been investigated for reversible immobilisation of bioactive species. Materials coated with penicillin V gave significant inhibition zones in antibacterial assays, showing efficacy in drug delivery. Finally, a range of diazo compounds with different substituents has been synthesised and their thermal stabilities have been assessed by differential scanning calorimetry technique.

Patch clamping is considered the gold standard in measuring the bioelectrical activity of a cell. It is used to detect and measure ion transport through ion channels located throughout a cell membrane. Ion movement is crucial to cell viability and cell-to-cell communication. Pharmaceutical companies increasingly target ion channels because of their significance in disease and to help design better targeted drugs. However, the traditional method of patch clamping is cumbersome and is being replaced by planar high throughput screening (HTS) systems. These systems are reaching their limits due to materials and cost of processing; cell handling methods and small varieties of applicable cell types are also issues to be addressed. In this work, the core components of a new kind of planar patch clamping device have been designed and developed, after analysis of currently available HTS systems. This design approaches patch clamping using polymers to overcome some of the limitations in current systems, specifically cell handling and positioning, by using a simple modification technique to provide distinct attractive areas for cell binding. This uniquely allows the culture of both single cells and cell networks to increase the range of cell types that can be measured and circumvents challenges from using suction to pull cells onto measurement holes. The components of the design are a 10 x 10 array of small holes drilled in a polymer then aligned modifications for precise cell placement are added and a planar electrode array for individual addressing of each cell. A study of methods to produce a leak-tight seal required between microfluidic chambers was done. Cell adhesion parameters for the modification techniques were established. The principle viability of this approach was confirmed using the modification technique to culture cells over holes and measure their resistance using a rig developed for this work.

To create functional surfaces for soft materials, such as polyurethanes, our approach is to use a semifluorinated surface modifier as minor component to the matrix material. The surface modifier, driving by reduction in surface energy, surface-concentrates to form a functionalized surface layer at the air-polymer interface. In our previous studies, linear PTMO-based polyurethanes were used as the matrix material. These systems undergo slow surface phase separation at room temperature due to the thermodynamically immiscibility of the soft blocks. In this study, chemically crosslinked matrix was developed to provides a steric hindrance to constrain the mobility of surface modifier and to form a kinetically stable surface. The physical property and morphology of base crosslinked matrix has been characterized using DSC, UTT, DMA and AFM. The surface morphology of surface modified crosslinked matrix has been characterized using AFM, DCA and XPS.

This thesis investigates the application of plasma immersion ion implantation (PIII) to polymers. PIII requires that a high negative potential be applied to the surface of the material while it is immersed in a plasma. This presents a problem for insulating materials such as polymers, since the implanting ions carry charge to the surface, resulting in a charge accumulation that effectively neutralises the applied potential. This causes the plasma sheath at the surface to collapse a short time after the potential is applied. Measurements of the sheath dynamics, including the collapsing sheath, are performed using an electric probe. The results are compared to theoretical models of the plasma sheath based on the Child-Langmuir law for high voltage sheaths. The theoretical model predicts well the sheath dynamics for conductive substrates. For insulating substrates the model can account for the experimental observations if the secondary electron coefficient is modified, justified on the basis of the poly-energetic nature of the implanting ions. If a conductive film is applied to the insulator surface the problem of charge accumulation can be avoided without compromising the effectiveness of PIII. The requirement for the film is that it be conductive, yet transparent to the incident ions. Experimental results are presented which confirm the effectiveness of the method. Theoretical estimates of the surface potential show that a film of the order of 5nm thickness can effectively circumvent the charge accumulation problem. Efforts to produce and characterise such a film form the final two chapters of this thesis. The optimal thickness is determined to be near the percolation threshold, where a marked increase in conductivity occurs. Spectroscopic ellipsometry is shown to be an excellent method to determine the film thickness and percolation threshold non-invasively. Throughout this work cathodic vacuum arcs are used to deposit thin films and as a source of metal plasmas. The design and construction of a pulsed cathodic vacuum arc forms a significant part of this thesis. Investigations of the cathode spots and power supply requirements are presented.

This thesis investigates the application of plasma immersion ion implantation (PIII) to polymers. PIII requires that a high negative potential be applied to the surface of the material while it is immersed in a plasma. This presents a problem for insulating materials such as polymers, since the implanting ions carry charge to the surface, resulting in a charge accumulation that effectively neutralises the applied potential. This causes the plasma sheath at the surface to collapse a short time after the potential is applied. Measurements of the sheath dynamics, including the collapsing sheath, are performed using an electric probe. The results are compared to theoretical models of the plasma sheath based on the Child-Langmuir law for high voltage sheaths. The theoretical model predicts well the sheath dynamics for conductive substrates. For insulating substrates the model can account for the experimental observations if the secondary electron coefficient is modified, justified on the basis of the poly-energetic nature of the implanting ions. If a conductive film is applied to the insulator surface the problem of charge accumulation can be avoided without compromising the effectiveness of PIII. The requirement for the film is that it be conductive, yet transparent to the incident ions. Experimental results are presented which confirm the effectiveness of the method. Theoretical estimates of the surface potential show that a film of the order of 5nm thickness can effectively circumvent the charge accumulation problem. Efforts to produce and characterise such a film form the final two chapters of this thesis. The optimal thickness is determined to be near the percolation threshold, where a marked increase in conductivity occurs. Spectroscopic ellipsometry is shown to be an excellent method to determine the film thickness and percolation threshold non-invasively. Throughout this work cathodic vacuum arcs are used to deposit thin films and as a source of metal plasmas. The design and construction of a pulsed cathodic vacuum arc forms a significant part of this thesis. Investigations of the cathode spots and power supply requirements are presented.

No description available.