In several practical applications, hot-finished steel pipe that exhibits Lüders bands is bent to strains of 2-3%. Lüders banding is a material instability that leads to inhomogeneous plastic deformation in the range of 1-4%. This work investigates the influence of Lüders banding on the inelastic response and stability of tubes under rotation controlled pure bending. It starts with the results of an experimental study involving tubes of several diameter-to-thickness ratios in the range of 33.2 to 14.7 and Lüders strains of 1.8% to 2.7%. In all cases, the initial elastic regime terminates at a local moment maximum and the local nucleation of narrow angled Lüders bands of higher strain on the tension and compression sides of the tube. As the rotation continues, the bands multiply and spread axially causing the affected zone to bend to a higher curvature while the rest of the tube is still at the curvature corresponding to the initial moment maximum. With further rotation of the ends, the higher curvature zone(s) gradually spreads while the moment remains essentially unchanged. For relatively low D/t tubes and/or short Lüders strains, the whole tube eventually is deformed to the higher curvature entering the usual hardening regime. Subsequently it continues to deform uniformly until the usual limit moment instability is reached. For high D/t tubes and/or materials with longer Lüders strains, the propagation of the larger curvature is interrupted by collapse when a critical length is Lüders deformed leaving behind part of the structure essentially undeformed. The higher the D/t and/or the longer the Lüders strain is, the shorter the critical length. This class of problems is analyzed using 3D finite elements while the material is modeled as an elastic-plastic solid with an “up-down-up” response over the extent of the Lüders strain, followed by hardening. The analysis reproduces the main features of the mechanical behavior provided the unstable part of the response is suitably calibrated. The uniform curvature elastic regime terminates with the nucleation of localized banded deformation. The bands appear in pockets on the most deformed sites of the tube and propagate into the hitherto intact part of the structure while the moment remains essentially unchanged. The Lüders-deformed section has a higher curvature, ovalizes more than the rest of the tube, and develops wrinkles with a characteristic wavelength. For every tube D/t there exists a threshold of Lüders strain separating the two types of behavior. This bounding value of Lüders strain was studied parametrically. / text

Previous experimental observations have shown that the pseudoelastic response of NiTi shape memory alloys (SMA) is localized in nature and proceeds through nucleation and propagation of localized deformation bands. It has also been observed that the mechanical response of SMAs is strongly affected by loading rate and cyclic degradation. These behaviors significantly limit the accurate modeling of SMA elements used in various devices and applications. The aim of this work is to provide engineers with a constitutive model that can accurately describe the dynamic, unstable pseudoelastic response of SMAs, including their cyclic response, and facilitate the reliable design of SMA elements. A 1-D phenomenological model is developed to simulate the localized phase transformations in NiTi wires during both loading and unloading. In this model, it is assumed that the untransformed particles located close to the transformed regions are less stable than those further away from the transformed regions. By consideration of the thermomechanical coupling among the stress, temperature, and latent heat of transformation, the analysis can account for strain-rate effects. Inspired by the deformation theory of plasticity, the 1-D model is extended to a 3-D macromechanical model of localized unstable pseudoelasticity. An important feature of this model is the reorientation of the transformation strain tensor with changes in stress tensor. Unlike previous modeling efforts, the present model can also capture the propagation of localized deformation during unloading. The constitutive model is implemented within a 2-D finite element framework to allow numerical investigation of the effect of strain rate and boundary conditions on the overall mechanical response and evolution of localized transformation bands in NiTi strips. The model successfully captures the features of the transformation front morphology, and pseudoelastic response of NiTi strip samples observed in previous experiments. The 1-D and 3-D constitutive models are further extended to include the plastic deformation and degradation of material properties as a result of cyclic loading.

Previous experimental observations have shown that the pseudoelastic response of NiTi shape memory alloys (SMA) is localized in nature and proceeds through nucleation and propagation of localized deformation bands. It has also been observed that the mechanical response of SMAs is strongly affected by loading rate and cyclic degradation. These behaviors significantly limit the accurate modeling of SMA elements used in various devices and applications. The aim of this work is to provide engineers with a constitutive model that can accurately describe the dynamic, unstable pseudoelastic response of SMAs, including their cyclic response, and facilitate the reliable design of SMA elements. A 1-D phenomenological model is developed to simulate the localized phase transformations in NiTi wires during both loading and unloading. In this model, it is assumed that the untransformed particles located close to the transformed regions are less stable than those further away from the transformed regions. By consideration of the thermomechanical coupling among the stress, temperature, and latent heat of transformation, the analysis can account for strain-rate effects. Inspired by the deformation theory of plasticity, the 1-D model is extended to a 3-D macromechanical model of localized unstable pseudoelasticity. An important feature of this model is the reorientation of the transformation strain tensor with changes in stress tensor. Unlike previous modeling efforts, the present model can also capture the propagation of localized deformation during unloading. The constitutive model is implemented within a 2-D finite element framework to allow numerical investigation of the effect of strain rate and boundary conditions on the overall mechanical response and evolution of localized transformation bands in NiTi strips. The model successfully captures the features of the transformation front morphology, and pseudoelastic response of NiTi strip samples observed in previous experiments. The 1-D and 3-D constitutive models are further extended to include the plastic deformation and degradation of material properties as a result of cyclic loading.

Previous experimental observations have shown that the pseudoelastic response of NiTi shape memory alloys (SMA) is localized in nature and proceeds through nucleation and propagation of localized deformation bands. It has also been observed that the mechanical response of SMAs is strongly affected by loading rate and cyclic degradation. These behaviors significantly limit the accurate modeling of SMA elements used in various devices and applications. The aim of this work is to provide engineers with a constitutive model that can accurately describe the dynamic, unstable pseudoelastic response of SMAs, including their cyclic response, and facilitate the reliable design of SMA elements. A 1-D phenomenological model is developed to simulate the localized phase transformations in NiTi wires during both loading and unloading. In this model, it is assumed that the untransformed particles located close to the transformed regions are less stable than those further away from the transformed regions. By consideration of the thermomechanical coupling among the stress, temperature, and latent heat of transformation, the analysis can account for strain-rate effects. Inspired by the deformation theory of plasticity, the 1-D model is extended to a 3-D macromechanical model of localized unstable pseudoelasticity. An important feature of this model is the reorientation of the transformation strain tensor with changes in stress tensor. Unlike previous modeling efforts, the present model can also capture the propagation of localized deformation during unloading. The constitutive model is implemented within a 2-D finite element framework to allow numerical investigation of the effect of strain rate and boundary conditions on the overall mechanical response and evolution of localized transformation bands in NiTi strips. The model successfully captures the features of the transformation front morphology, and pseudoelastic response of NiTi strip samples observed in previous experiments. The 1-D and 3-D constitutive models are further extended to include the plastic deformation and degradation of material properties as a result of cyclic loading. / Applied Science, Faculty of / Mechanical Engineering, Department of / Graduate