International Telemetering Conference Proceedings / October 27-30, 1997 / Riviera Hotel and Convention Center, Las Vegas, Nevada / Caterpillar Inc. has been testing construction and mining equipment using Computerized Analysis Vans for two decades. During our latest van upgrade, we chose to move to PCM/FM from FM/FM mainly to increase the channel count. We also replaced our old signal conditioning that used span and balance potentiometers with computer programmable signal conditioning. This new signal conditioning requires that the gain and balance point be calculated for every channel on each test. The formulas for these calculations depend on the sensor, the signal conditioning card used, and the test requirements. Due to the number and variety of machines tested at the Caterpillar Proving Grounds, these calculations needed to be automated. Using a few initial parameters and the information from our sensor calibration database, each channel’s balance point, gain, and expected slope are calculated. This system has increased productivity, accuracy, and consistency over manually calculating these parameters. This paper covers the sensor database, the calculated parameters and an overview of the way the system works.

Thesis (Ph. D.)--Virginia Polytechnic Institute and State University, 1993. / Vita. Abstract. Includes bibliographical references (leaves 229-237). Also available via the Internet.

Thesis (M.A.)--University of North Carolina at Wilmington, 2006. / Includes bibliographical references (leaf: [41])

ITC/USA 2005 Conference Proceedings / The Forty-First Annual International Telemetering Conference and Technical Exhibition / October 24-27, 2005 / Riviera Hotel & Convention Center, Las Vegas, Nevada / Pulse Code Modulation (PCM) Encoders used in Telemetry Instrumentation systems have traditionally been implemented using sequencer or state-machine based micro-architectures with distributed control and signal acquisition components. This architecture requires the use of many discrete electronic components and custom micro-code programming or state machine development for the control of the systems. The advent of relatively high-speed microcontrollers with embedded signal acquisition subsystems has brought about the ability to implement highly integrated PCM Encoder systems using fewer components and standardized programming methods. This paper will discuss sequencer based PCM encoders for background and then introduce the concept of Microcontroller Based PCM Encoders for Telemetry Instrumentation. Specific design examples will be introduced. Advantages and disadvantages of the two techniques will be discussed.

International Telemetering Conference Proceedings / October 30-November 02, 1989 / Town & Country Hotel & Convention Center, San Diego, California / Aydin Vector Division has developed and manufactured an airborne, high shock, wideband FM/FM telemetry system for Saab Missiles AB in Sweden. This system was presented in the ITC Proceedings of 1988, Volume XXIV, pp 71-84 (Ref [1]). Three such systems were supplied. Saab Missiles AB also awarded Aydin Vector Division with an additional order for a larger number of high shock, computer based, specially designed, miniature PCM/FM airborne telemetry systems. These systems were developed, manufactured and supplied to Saab Missiles AB, and have been extensively and successfully used in the Swedish program. The PCM/FM telemetry package described in this paper was used for the system testing and the firing trials program of a mortar projectile, where the measurement requirements included micro processor interfaces, as well as a high amount of analog and bi-level data channels. The paper covers the specifications of the PCM/FM system mentioned above, the concept that was used to meet these specifications, the system’s mechanical and electrical design, the packaging technique and some of the test results.

International Telemetering Conference Proceedings / October 29-November 02, 1990 / Riviera Hotel and Convention Center, Las Vegas, Nevada / The new generation of advanced tactical aircraft and missiles places unique demands on the electronic and mechanical designs for flight test instrumentation, high bit rates, operating temperature range and system interconnect wiring requirements. This paper describes a microminiature PCM distributed data acquisition system with integral signal conditioning (MMSC) which has been used in advanced aircraft and missile flight testing. The MMSC system is constructed from microminiature, stackable modules which allow the user to reconfigure the system as the requirements change. A second system is also described which uses the same circuitry in hermetic hybrid packages on plug-in circuit boards.

International Telemetering Conference Proceedings / October 28-31, 1996 / Town and Country Hotel and Convention Center, San Diego, California / This paper describes some of the signal conditioning and processing circuits that were developed to reconstruct the doppler video signal from a radar receiver under test. The reconstructed doppler video signal is then digitized and put into a telemetry frame for transmission to a ground receiving station.

Thesis (Ph. D.)--Florida State University, 2003. / Advisor: Dr. Frank Gross, Florida State University, FAMU-FSU College of Engineering, Dept. of Electrical and Computer Engineering. Title and description from dissertation home page (viewed Oct. 3, 2003). Includes bibliographical references.

No description available.

This research report reviews the basics of pulse code modulation (PCM) techniques and includes a special encoder design for a system which uses a laser diode output for the transmitted pulse. The text discusses PCM and its features, PCM formats, synchronization, and various accepted PCM codes. The encode circuit design is complete with a description of the circuit, circuit components, and operation. Included are the necessary diagrams, figures, specifications, and parts list. The transmitted output of the design circuit has a repetition rate of one megabit per second.