Although, the use of vinyl pyridine polymers, especially as matrices for nanoparticle synthesis, is growing considerably, the knowledge of thermal degradation behavior is still missing in the literature. In this study, thermal degradation characteristics of the homopolymers / poly(4-vinylpyridine), P4VP, and poly(2-vinylpyridine), P2VP, the diblock copolymers / polystyrene-blockpoly( 2-vinylpyridine), (PS-b-P2VP) and polystyrene-block-poly(4-vinylpyridine), (PS-b-P4VP), and the metal functional vinyl polymers / cobalt-polystyrene-blockpoly( 2-vinylpyridine) and cobalt-polystyrene-block-poly(4-vinylpyridine) were investigated by direct pyrolysis mass spectrometry. The effects of the position of the nitrogen in the pyridine ring, composition and molecular weight of diblock copolymer and coordination of the metal to the pyridine ring of the copolymer on thermal behavior were also investigated. The results showed that unlike most of the vinyl polymers that decompose via depolymerization, P2VP degrades through opposing reaction pathways / depolymerization, proton transfer to N atom in the pyridine ring yielding unsaturated linkages on the polymer backbone that decompose slightly at higher temperatures and loss of pyridine units. On the other hand the thermally less stable P4VP decomposition follows v depolymerization in accordance to general expectations. Another finding was the independent decomposition of both components of the diblock polymers, (PS-b- P2VP) and (PS-b-P4VP). Thermal degradation occurs in two main steps, the thermally less stable P2VP or P4VP chains degrade in the first step and in the second step decomposition of PS takes place. It was also concluded that upon coordination of metal, thermal stability of both P2VP and P4VP increases significantly. For metal functional diblock copolymers thermal degradation of chains coordinated to Co metal through N in the pyridine ring occurred in three steps / cleavage of pyridine coordinated to Co, coupling and H-transfer reactions yielding unsaturated and/or crosslinked structure and decomposition of these thermally more stable unsaturated and/or crosslinked blocks. TEM imaging of the metal functional block copolymers along with the results of the pyrolysis mass spectrometry pointed out that PS-b-P2VP polymer is a better and more effective matrix for nanoparticle synthesis.

The use of various biodegradable polymers for the improvement of different controlled and long-lasting drug release systems is an active research area in recent years. The application of different metal prostheses, especially titanium based ones, to the human body is also very common. A most important disadvantage of these prostheses is the risk of infection at the application areas that necessitates the removing of the prosthesis with a second surgical operation and reapplication of it after recovery. One of the best ways to solve this problem is to render metal prostheses infection free with controlled and sustainable drug (antibiotic) release systems. The long term sustained release of relevant antibiotics from the various biodegradable polymer coated metal implants is studied in this thesis. Virtual fatigue analysis and drug loading capacities of titanium and stainless steel samples with different surface pattern and modifications were studied. Various biodegradable polymer and drug combinations were examined and used for coating of metal prosthesis. The aim is to design polymer-drug coated metal implants that are capable of releasing a feasible amount of drug up to a period of at least 1 month. Various coating techniques and surface modifications were also employed to improve the adhesional properties of the drug containing polymers. Their adhesion abilities on the metal substrates were tested by Lap-shear and T-peel tests. Polymer degradation kinetics was followed by viscosity studies. Calibration lines for different drugs were obtained and drug releases on different systems were followed by using UV spectroscopy and microbial antibiotic sensitivity tests. Among the techniques applied to prevent fast release of drugs initially, the coatings of Vancomycin absorbed &amp / #946 / -TCP (&amp / #946 / -tricalcium phosphate) homogeneously distributed in poly(D,L-lactide-co-glycolide) solution in chloroform followed by an inert coating with poly(L-lactide) system proved to be feasible. By this technique, initial burst release was minimized and drug release from implants lasted nearly 2 months. Multiple coatings on polymer plus drug coating layer also gave promising results. In vivo studies on dorsal muscles of native rabbits with antibiotic loaded implants gave no negative effect on the surrounding tissues with high compatibility free of infection.

The aim of this study was to improve the mechanical and electrical properties of conductive polymer composites. For this purpose, different studies were performed in this dissertation. In order to investigate the effects of the carbon nanotube (CNT) surface treatment on the morphology, electrical and mechanical properties of the composites, poly(ethylene terephthalate) (PET) based conductive polymer composites were prepared by using as-received, purified and modified carbon nanotubes in a twin screw extruder. During the purification of carbon nanotubes, surface properties of carbon nanotubes were altered by purifying them with nitric acid (HNO3), sulfuric acid (H2SO4), ammonium hydroxide (NH4OH) and hydrogen peroxide (H2O2) mixtures. Electron Spectroscopy for Chemical Analysis (ESCA) results indicated the removal of metallic catalyst residues from the structure of carbon nanotubes and increase in the oxygen content of carbon nanotube surface as a result of purification procedure. Surface structure of the purified carbon nanotubes was also modified by treatment with sodium dodecyl sulfate (SDS), poly(ethylene glycol) (PEG) and diglycidyl ether of Bisphenol A (DGEBA). Fourier Transformed Infrared Spectroscopy (FTIR) spectra of the carbon nanotube samples indicated the existence of functional groups on the surfaces of carbon nanotubes after modification. All composites prepared with purified and modified carbon nanotubes had higher electrical resistivities, tensile and impact strength values than those of the composite based on as-received carbon nanotubes, due to the functional groups formed on the surfaces of carbon nanotubes during surface treatment. In order to investigate the effects of alternative composite preparation methods on the electrical and mechanical properties of the composites, in-situ microfiber reinforced conductive polymer composites consisting of high density polyethylene (HDPE), poly(ethylene terephthalate) and carbon nanotubes were prepared in a twin screw extruder followed by hot stretching of PET/CNT phase in HDPE matrix. Composites were produced by using as-received, purified and PEG treated carbon nanotubes. SEM micrographs of the hot stretched composites pointed out the existence of in-situ PET/CNT microfibers dispersed in HDPE matrix up to 1 wt. % carbon nanotube loadings. Electrical conductivity values of the microfibrillar composites were higher than that of the composites prepared without microfiber reinforcement due to the presence of continuous PET/CNT microfibers with high electrical conductivity in the structure. To investigate the potential application of conductive polymer composites, the effects of surfactant usage and carbon nanotube surface modification / on the damage sensing capability of the epoxy/carbon nanotube/glass fiber composite panels during mechanical loadings were studied. Surface modification of the carbon nanotubes was performed by using hexamethylene diamine (HMDA). 4-octylphenol polyethoxylate (nonionic) (Triton X-100) and cetyl pyridinium chloride (cationic) (CPC) were used as surfactants during composite preparation. Electrical resistivity measurements which were performed during the impact, tensile and fatigue tests of the composite panels showed the changes in damage sensing capabilities of the composites. Surface treatment of carbon nanotubes and the use of surfactants decreased the carbon nanotube particle size and improved the dispersion in the composites which increased the damage sensitivity of the panels.

In the latest years, many studies especially on characterization and synthesis of polyoxazolines have been made. During these studies, new polyoxazolines such as poly(2-isopropyl-2-oxazoline) (PIPOX), poly(2-(3-butenyl)-2-oxazoline) (PBOX) and modified PBOX were synthesized. However, there has been no investigation on their thermal characteristics such as thermal stability and thermal degradation products. In this study, thermal degradation characteristics, thermal degradation products and thermal stability of PIPOX, PBOX and modified PBOX polymers PBOX-Perf, PBOX-Thiop, PBOX-Sug, PBOX-SP and PBOX-TP were investigated. In this study mercaptans 1H,1H,2H,2H-perfluoro-octanethiol, 3-mercapto-1,2 propanediol, thio-&beta / -D-glucose derivative and their mixture were used in PBOX modifications. The effect of modification of PBOX with different mercaptans on thermal characteristics was also analyzed. For the PIPOX, formations of protonated monomer and oligomers from dimer to heptamer were observed. However, when the isopropyl group changes with 3-butenyl group, protonated oligomers up to trimer were observed because the crosslinking formed during the polymerization of unsaturated butenyl inhibited the production of oligomers. In addition to this, thermal degradation at lower temperatures was observed. The change in thermal stability and thermal degradation products were observed as a result of modification of PBOX with different mercaptans. Unlike PBOX-Sug thermal degradation started at very low temperatures for PBOX-Thiop and PBOX-Perf. This degradation observed at lower temperatures disappeared for PBOX-SP and PBOX-TP. For PBOX-Perf, PBOX-Sug and PBOX- Thiop, decomposition of side chains at low temperatures and decomposition of the main chain at high temperatures were observed. Although the same thermal degradation behavior for PBOX-TP and PBOX-Thiop was expected, since PBOX-TP was obtained as a result of modification of PBOX with high amounts of mercaptan used in PBOX-Thiop and small amounts of mercaptan used in the PBOX-Perf, the results show that neither PBOX-Thiop nor PBOX-Perf thermal degradation behavior are dominant. This is also valid for PBOX-SP. PBOX-SP has higher thermal stability when compared to PBOX-Sug.

Incorporation of monoacetylferrocene to the sulfonated polystyrene ionomers imparted some changes in the properties of sulfonated polystyrene. Sulfonation was carried out by acetic anhydride and concentrated sulphuric acid. The sulfonation reaction and the degree of sulfonation were determined by analytical titration and adiabatic bomb calorimeter . For this purpose, sulfonated polystyrene (SPS) samples with varying percentages of sulfonation were prepared between 0.85% and 6.51%. Monoacetyl ferrocene was used in equivalent amount of sulfonation through addition procedure. FTIR Spectroscopy was one of the major techniques used to support the successful addition of AcFe to the SPS samples. Altering the sulfonation degree did not change the characteristic peak positions, but increased the peak intensities with increasing the degrees of sulfonation. Mechanical properties of resultant polymers were investigated. As a result, elastic modulus of polymers decreased by the amount of monoacetylferrocene. Thermal characteristic were found by Differential Scanning Calorimeter (DSC). Thermal analysis revealed that sulfonated polystyrene samples after addition of monoacetylferrocene displayed lower values of Tg. Microscopic analysis were made by Scanning Electron Microscopy (SEM) and single phase for each sample was observed. Besides, energy dispersed micro analysis showed an increase in the intensity of the iron (II) peaks that is related to the amount of monoacetylferrocene added to the SPS samples. Flame retardancy for each polymer was also examined and found that addition of monoacetylferrocene to sulfonated polystyrene does not change the Limiting Oxygen Index value (LOI)(17). However, LOI value for polystyrene is 18.