Sewer and oil pipeline spillage issues have become major causes of pollution in urban and rural areas usually caused by blockages in the water storage and drainage system, and oil spillage of underground oil pipelines. An effective way of avoiding this problem will be by deploying some mechanism to monitor these installations at each point in time and reporting unusual liquid activity to the relevant authorities for prompt action to avoid a flooding or spillage occurrence. This research work presents a low cost energy efficient liquid level monitoring technique using Radio Frequency Identification Technology. Passive UHF RFID tags have been designed, modelled and optimized. A simple rectangular tag, the P-shaped tag and S-shaped tag with UHF band frequency of operation (850-950 MHz) has been designed and modelled. Detailed parametric analysis of the rectangular tag is made and the optimised design results analysed and presented in HFSS and Matlab. The optimised rectangular tag designs are then deployed as level sensors in a gully pot. Identical tags were deployed to detect 4 distinct levels in alternate positions and a few inches in seperation distance within the gully pot height (Low, Mid, High and Ultra high). The radiation characteristic of tag sensors in deployment as modelled on HFSS is observed to show consistent performance with application requirements. An in-manhole chamber antenna for an underground communication system is analysed, designed, deployed and measured. The antenna covers dual-band impedance bandwidths (i.e. 824 to 960 MHz, and 1710 to 2170 MHz). The results show that the antenna prototype exhibits sufficient impedance bandwidth, suitable radiation characteristics, and adequate gains for the required underground wireless sensor applications. Finally, a Linearly Shifted Quadrifilar Helical Antenna (LSQHA) designed using Genetic Algorithm optimisation technique for adoption as an RFID reader antenna is proposed and investigated. The new antenna confirms coverage of the RFID bandwidth 860-960 MHz with acceptable power gain of 13.1 dBi.

Sewer and oil pipeline spillage issues have become major causes of pollution in urban and rural areas usually caused by blockages in the water storage and drainage system, and oil spillage of underground oil pipelines. An effective way of avoiding this problem will be by deploying some mechanism to monitor these installations at each point in time and reporting unusual liquid activity to the relevant authorities for prompt action to avoid a flooding or spillage occurrence. This research work presents a low cost energy efficient liquid level monitoring technique using Radio Frequency Identification Technology. Passive UHF RFID tags have been designed, modelled and optimized. A simple rectangular tag, the P-shaped tag and S-shaped tag with UHF band frequency of operation (850-950 MHz) has been designed and modelled. Detailed parametric analysis of the rectangular tag is made and the optimised design results analysed and presented in HFSS and Matlab. The optimised rectangular tag designs are then deployed as level sensors in a gully pot. Identical tags were deployed to detect 4 distinct levels in alternate positions and a few inches in seperation distance within the gully pot height (Low, Mid, High and Ultra high). The radiation characteristic of tag sensors in deployment as modelled on HFSS is observed to show consistent performance with application requirements. An in-manhole chamber antenna for an underground communication system is analysed, designed, deployed and measured. The antenna covers dual-band impedance bandwidths (i.e. 824 to 960 MHz, and 1710 to 2170 MHz). The results show that the antenna prototype exhibits sufficient impedance bandwidth, suitable radiation characteristics, and adequate gains for the required underground wireless sensor applications. Finally, a Linearly Shifted Quadrifilar Helical Antenna (LSQHA) designed using Genetic Algorithm optimisation technique for adoption as an RFID reader antenna is proposed and investigated. The new antenna confirms coverage of the RFID bandwidth 860-960 MHz with acceptable power gain of 13.1 dBi. / Petroleum Technology Development Fund (PTDF) and National Space Research and Development Agency (NASRDA).

The objectives of this research work are to investigate, design and implement circularly-polarized antennas to be used for handheld satellite mobile communication and wireless sensor networks. Several antennas such as Quadrifilar Spiral Antennas (QSAs), two arm Square Spiral and stripline or coaxially-fed microstrip patch antennas are developed and tested. These antennas are investigated and discussed to operate at L band (1.61-1.6214GHz) and ISM band (2.4835-2.5GHz) A substantial size reduction was achieved compared to conventional designs by introducing special modifications to the antenna geometries. Most of the antennas are designed to produce circularly-polarized broadside-beam except for wireless sensor network application a circularly-polarized conical-beam is considered. The polarization purity and Specific Absorption Rate (SAR) of two dual-band antennas for satellite-mobile handsets next to the human head are investigated and discussed, using a hybrid computational method. A small distance between the head and the handset is chosen to highlight the effects of the relatively high-radiated power proposed from this particular antenna. A Genetic Algorithm in cooperation with an electromagnetic simulator has been introduced to provide fast, accurate and reliable solutions for antenna design structures. Circularly-polarized quadrifilar helical antenna handset and two air-dielectric microstrip antennas were studied. The capabilities of GA are shown as an efficient optimisation tool for selecting globally optimal parameters to be used in simulations with an electromagnetic antenna design code, seeking convergence to designated specifications. The results in terms of the antenna size and radiation performance are addressed, and compared to measurements and previously published data.

The objectives of this research work are to investigate, design and implement circularly-polarized antennas to be used for handheld satellite mobile communication and wireless sensor networks. Several antennas such as Quadrifilar Spiral Antennas (QSAs), two arm Square Spiral and stripline or coaxially-fed microstrip patch antennas are developed and tested. These antennas are investigated and discussed to operate at L band (1.61-1.6214GHz) and ISM band (2.4835-2.5GHz) A substantial size reduction was achieved compared to conventional designs by introducing special modifications to the antenna geometries. Most of the antennas are designed to produce circularly-polarized broadside-beam except for wireless sensor network application a circularly-polarized conical-beam is considered. The polarization purity and Specific Absorption Rate (SAR) of two dual-band antennas for satellite-mobile handsets next to the human head are investigated and discussed, using a hybrid computational method. A small distance between the head and the handset is chosen to highlight the effects of the relatively high-radiated power proposed from this particular antenna. A Genetic Algorithm in cooperation with an electromagnetic simulator has been introduced to provide fast, accurate and reliable solutions for antenna design structures. Circularly-polarized quadrifilar helical antenna handset and two air-dielectric microstrip antennas were studied. The capabilities of GA are shown as an efficient optimisation tool for selecting globally optimal parameters to be used in simulations with an electromagnetic antenna design code, seeking convergence to designated specifications. The results in terms of the antenna size and radiation performance are addressed, and compared to measurements and previously published data.