In this thesis, intelligent metamaterial was designed to reduce the peak specific absorption rate (SAR) value. Intelligent metamaterial means that when the antenna is far away from a human head, the metamaterial behaves like air and it does not affect the antenna performance; when the antenna is close to a human head, however, the metamaterial acts like a single negative (SNG) material. We designed two kinds of intelligent metamaterial structures. One makes use of impedance mismatching, and the other makes use of the frequency band shift property to reduce the peak SAR value at the operating frequency. The former structure is broadband, and it can reduce the peak SAR value by 56.7%. The latter structure has a much smaller size compared to the former one, and it is suitable for cellular phone applications. The peak SAR value can be reduced by 40% using the latter structure. The proposed two kinds of the intelligent metamaterial structures do not affect the antenna performance. Finally, the intelligent metamaterial has been applied to a cellular phone. The dimension of the intelligent metamaterial is only 40 mm ¡Ñ 20 mm ¡Ñ 0.8 mm. The intelligent metamaterial does not affect the antenna performance when the antenna is far away from a human head. When the antenna is close to a human head, the peak SAR is reduced by 41.7%.

The beginning of the 21 st century is characterised, among others, by the evolution in telecommunications. The rapid growth of mobile communications and the variety of applications proposed for the third generation (3G) systems require long operation time, low weight and cost for terminals, as well as improved link quality. For this reason a good efficiency and low profile antennas with low absorption losses by the user are desirable. The Planar Inverted-F Antenna (PIFA) is shown to result into low SAR values and high efficiency when operating in the proximity of the user. Despite these advantages, PIFA is also characterised by narrow bandwidth that limits its practical use. The first part of this work is dedicated to the measurements and evaluation of the radiation characteristics of the PIFA and other wire antennas both in the near and far fields. In addition, novel methods of PIFA tuning are presented. These include the repositioning of the shorting pin and modification of its capacitance. By using these techniques, the effective bandwidth of the PIFA can be increased to satisfy the GSM900 and DCS 1800 system bandwidth requirements. Dual-band and electronically tuned PIFA prototypes are also included. The effects of the handset size on the mass averaged Specific Absorption Rate (SAR), and antenna efficiency are investigated. The appropriate choice of handset can result in up to 30%-reduced peak SAR. The computed SAR values from PIFA are compared with those resulting from the use of a handset equipped with quarter wavelength monopole antenna. A new measure referred to as the 3dB SAR volume is proposed. This measure provides better understanding of the absorbed power distribution in the operator's head. Results obtained in the course of study show that low profile handset antennas, such as the PIFA, present in addition to dual resonance and low reflection losses, reduced SAR values, high efficiency and low 3dB SAR volume. Finally, SAR and 3dB SAR volume values from simulations on 5- and 10- years old child head models are compared with their equivalents for adult models from which appropriate conclusions are drawn.

A grande maioria da população mundial está crescentemente exposta à radiação eletromagnética proveniente de fontes que muitas vezes estão localizadas nas proximidades do corpo. A radiação eletromagnética é considerada um agente possivelmente cancerígeno para as pessoas, classificação 2B indicada pela Organização Mundial da Saúde-OMS (WHO/IARC, 2011). Devido às preocupações em relação aos riscos associados a esta exposição existem normas que recomendam os valores máximos de exposição permitidos (ICNIRP, 1998; FCC, 2001). A correta avaliação das doses de radiação é, portanto, relevante. Este trabalho tem a finalidade de avaliar o impacto dos resultados do cálculo da dose da Taxa de Absorção Específica (SAR) em usuários expostos a radiação por tablets operando na faixa de radiocomunicações Wi-fi. Os três modelos existentes de cabeça humana utilizados serão um manequim homogêneo SAM phantom e dois modelos de cabeça realistas heterogêneos: um adulto masculino e uma criança masculina. Será também utilizado nas simulações um modelo masculino de criança que foi desenvolvido através de imagens de tomografia computadorizada (TC) pelo processo de segmentação feito no software AMIRA. Será utilizado um modelo genérico de tablet. Os parâmetros dosimétricos usados para simulação da SAR serão computados pelo software SEMCAD X que é baseado no Método das Diferenças Finitas no Domínio do Tempo (FDTD). Será criado também um código do Método FDTD através do software MATLAB que servirá para a escolha dos parâmetros do SEMCAD X. A distância entre o tablet e os modelos de cabeças varia de 50 mm a 300 mm. Os resultados da SAR serão comparados com os limites de exposição recomendados pelas normas internacionais. Também serão simuladas diferentes posições da antena no tablet. Da análise dos resultados foi constatado que os valores de SAR são muito baixos e todos os resultados ficaram dentro dos limites do psSAR recomendados pela FCC de 1,6 W/kg em cada 1 g de tecido e de 2 W/kg em cada 10 g de tecido estabelecidos pela ICNIRP. Comparando os valores de SAR do modelo SAM com o modelo DUKE, o modelo SAM se mostra conservador, porém quando a comparação é feita com as crianças o SAM deixa de ser conservador. / The vast majority of the world population is increasingly exposed to electromagnetic radiation from sources which are often located near to the body. Electromagnetic radiation is considered a possible carcinogen for people, classification 2B indicated by the World Health Organization-WHO (WHO/IARC, 2011). Due to concerns regarding the risks associated with this exposition there are regulations suggesting maximum allowed exposure values (ICNIRP, 1998; FCC, 2001). The correct evaluation of radiation doses is therefore relevant. This work aims to assess the impact of the results of the calculation of Specific Absorption Rate dose (SAR) in users exposed to radiation from tablets operating in the Wi-fi band. The three existing models of human head used are a homogeneous dummy SAM phantom and two heterogeneous realistic head models: a male adult and a male child. It will also be used in the simulations a male child model which was developed from computed tomography (CT) imaging using the AMIRA software for the segmentation process. A generic model of tablet is used. Dosimetric parameters used for simulation of the SAR are computed using the SEMCAD X software which is based on the Finite Difference Method in Time Domain (FDTD). A FDTD code was developed using the MATLAB software in order to help to choose the input SEMCAD X parameters. The distances between the tablet and the head of the models varies from 50 mm to 300 mm. SAR results are compared with the exposure limits recommended by international standards. Different antenna positions on the tablet are simulated too. Examining the results it was found that the SAR values are very low and all results are within the psSAR limits recommended by FCC (1,6 W/kg averaged over 1 g of tissue) and by ICNIRP (2 W/kg in 10 g of tissue). Comparing the SAR in the SAM model with the SAR in the DUKE model, the SAM model shows to be conservative. However, when compared with the children, the SAM is not conservative.

A grande maioria da população mundial está crescentemente exposta à radiação eletromagnética proveniente de fontes que muitas vezes estão localizadas nas proximidades do corpo. A radiação eletromagnética é considerada um agente possivelmente cancerígeno para as pessoas, classificação 2B indicada pela Organização Mundial da Saúde-OMS (WHO/IARC, 2011). Devido às preocupações em relação aos riscos associados a esta exposição existem normas que recomendam os valores máximos de exposição permitidos (ICNIRP, 1998; FCC, 2001). A correta avaliação das doses de radiação é, portanto, relevante. Este trabalho tem a finalidade de avaliar o impacto dos resultados do cálculo da dose da Taxa de Absorção Específica (SAR) em usuários expostos a radiação por tablets operando na faixa de radiocomunicações Wi-fi. Os três modelos existentes de cabeça humana utilizados serão um manequim homogêneo SAM phantom e dois modelos de cabeça realistas heterogêneos: um adulto masculino e uma criança masculina. Será também utilizado nas simulações um modelo masculino de criança que foi desenvolvido através de imagens de tomografia computadorizada (TC) pelo processo de segmentação feito no software AMIRA. Será utilizado um modelo genérico de tablet. Os parâmetros dosimétricos usados para simulação da SAR serão computados pelo software SEMCAD X que é baseado no Método das Diferenças Finitas no Domínio do Tempo (FDTD). Será criado também um código do Método FDTD através do software MATLAB que servirá para a escolha dos parâmetros do SEMCAD X. A distância entre o tablet e os modelos de cabeças varia de 50 mm a 300 mm. Os resultados da SAR serão comparados com os limites de exposição recomendados pelas normas internacionais. Também serão simuladas diferentes posições da antena no tablet. Da análise dos resultados foi constatado que os valores de SAR são muito baixos e todos os resultados ficaram dentro dos limites do psSAR recomendados pela FCC de 1,6 W/kg em cada 1 g de tecido e de 2 W/kg em cada 10 g de tecido estabelecidos pela ICNIRP. Comparando os valores de SAR do modelo SAM com o modelo DUKE, o modelo SAM se mostra conservador, porém quando a comparação é feita com as crianças o SAM deixa de ser conservador. / The vast majority of the world population is increasingly exposed to electromagnetic radiation from sources which are often located near to the body. Electromagnetic radiation is considered a possible carcinogen for people, classification 2B indicated by the World Health Organization-WHO (WHO/IARC, 2011). Due to concerns regarding the risks associated with this exposition there are regulations suggesting maximum allowed exposure values (ICNIRP, 1998; FCC, 2001). The correct evaluation of radiation doses is therefore relevant. This work aims to assess the impact of the results of the calculation of Specific Absorption Rate dose (SAR) in users exposed to radiation from tablets operating in the Wi-fi band. The three existing models of human head used are a homogeneous dummy SAM phantom and two heterogeneous realistic head models: a male adult and a male child. It will also be used in the simulations a male child model which was developed from computed tomography (CT) imaging using the AMIRA software for the segmentation process. A generic model of tablet is used. Dosimetric parameters used for simulation of the SAR are computed using the SEMCAD X software which is based on the Finite Difference Method in Time Domain (FDTD). A FDTD code was developed using the MATLAB software in order to help to choose the input SEMCAD X parameters. The distances between the tablet and the head of the models varies from 50 mm to 300 mm. SAR results are compared with the exposure limits recommended by international standards. Different antenna positions on the tablet are simulated too. Examining the results it was found that the SAR values are very low and all results are within the psSAR limits recommended by FCC (1,6 W/kg averaged over 1 g of tissue) and by ICNIRP (2 W/kg in 10 g of tissue). Comparing the SAR in the SAM model with the SAR in the DUKE model, the SAM model shows to be conservative. However, when compared with the children, the SAM is not conservative.

A grande maioria da população mundial está crescentemente exposta à radiação eletromagnética proveniente de fontes que muitas vezes estão localizadas nas proximidades do corpo. A radiação eletromagnética é considerada um agente possivelmente cancerígeno para as pessoas, classificação 2B indicada pela Organização Mundial da Saúde-OMS (WHO/IARC, 2011). Devido às preocupações em relação aos riscos associados a esta exposição existem normas que recomendam os valores máximos de exposição permitidos (ICNIRP, 1998; FCC, 2001). A correta avaliação das doses de radiação é, portanto, relevante. Este trabalho tem a finalidade de avaliar o impacto dos resultados do cálculo da dose da Taxa de Absorção Específica (SAR) em usuários expostos a radiação por tablets operando na faixa de radiocomunicações Wi-fi. Os três modelos existentes de cabeça humana utilizados serão um manequim homogêneo SAM phantom e dois modelos de cabeça realistas heterogêneos: um adulto masculino e uma criança masculina. Será também utilizado nas simulações um modelo masculino de criança que foi desenvolvido através de imagens de tomografia computadorizada (TC) pelo processo de segmentação feito no software AMIRA. Será utilizado um modelo genérico de tablet. Os parâmetros dosimétricos usados para simulação da SAR serão computados pelo software SEMCAD X que é baseado no Método das Diferenças Finitas no Domínio do Tempo (FDTD). Será criado também um código do Método FDTD através do software MATLAB que servirá para a escolha dos parâmetros do SEMCAD X. A distância entre o tablet e os modelos de cabeças varia de 50 mm a 300 mm. Os resultados da SAR serão comparados com os limites de exposição recomendados pelas normas internacionais. Também serão simuladas diferentes posições da antena no tablet. Da análise dos resultados foi constatado que os valores de SAR são muito baixos e todos os resultados ficaram dentro dos limites do psSAR recomendados pela FCC de 1,6 W/kg em cada 1 g de tecido e de 2 W/kg em cada 10 g de tecido estabelecidos pela ICNIRP. Comparando os valores de SAR do modelo SAM com o modelo DUKE, o modelo SAM se mostra conservador, porém quando a comparação é feita com as crianças o SAM deixa de ser conservador. / The vast majority of the world population is increasingly exposed to electromagnetic radiation from sources which are often located near to the body. Electromagnetic radiation is considered a possible carcinogen for people, classification 2B indicated by the World Health Organization-WHO (WHO/IARC, 2011). Due to concerns regarding the risks associated with this exposition there are regulations suggesting maximum allowed exposure values (ICNIRP, 1998; FCC, 2001). The correct evaluation of radiation doses is therefore relevant. This work aims to assess the impact of the results of the calculation of Specific Absorption Rate dose (SAR) in users exposed to radiation from tablets operating in the Wi-fi band. The three existing models of human head used are a homogeneous dummy SAM phantom and two heterogeneous realistic head models: a male adult and a male child. It will also be used in the simulations a male child model which was developed from computed tomography (CT) imaging using the AMIRA software for the segmentation process. A generic model of tablet is used. Dosimetric parameters used for simulation of the SAR are computed using the SEMCAD X software which is based on the Finite Difference Method in Time Domain (FDTD). A FDTD code was developed using the MATLAB software in order to help to choose the input SEMCAD X parameters. The distances between the tablet and the head of the models varies from 50 mm to 300 mm. SAR results are compared with the exposure limits recommended by international standards. Different antenna positions on the tablet are simulated too. Examining the results it was found that the SAR values are very low and all results are within the psSAR limits recommended by FCC (1,6 W/kg averaged over 1 g of tissue) and by ICNIRP (2 W/kg in 10 g of tissue). Comparing the SAR in the SAM model with the SAR in the DUKE model, the SAM model shows to be conservative. However, when compared with the children, the SAM is not conservative.

The objectives of this research work are to investigate, design and implement circularly-polarized antennas to be used for handheld satellite mobile communication and wireless sensor networks. Several antennas such as Quadrifilar Spiral Antennas (QSAs), two arm Square Spiral and stripline or coaxially-fed microstrip patch antennas are developed and tested. These antennas are investigated and discussed to operate at L band (1.61-1.6214GHz) and ISM band (2.4835-2.5GHz) A substantial size reduction was achieved compared to conventional designs by introducing special modifications to the antenna geometries. Most of the antennas are designed to produce circularly-polarized broadside-beam except for wireless sensor network application a circularly-polarized conical-beam is considered. The polarization purity and Specific Absorption Rate (SAR) of two dual-band antennas for satellite-mobile handsets next to the human head are investigated and discussed, using a hybrid computational method. A small distance between the head and the handset is chosen to highlight the effects of the relatively high-radiated power proposed from this particular antenna. A Genetic Algorithm in cooperation with an electromagnetic simulator has been introduced to provide fast, accurate and reliable solutions for antenna design structures. Circularly-polarized quadrifilar helical antenna handset and two air-dielectric microstrip antennas were studied. The capabilities of GA are shown as an efficient optimisation tool for selecting globally optimal parameters to be used in simulations with an electromagnetic antenna design code, seeking convergence to designated specifications. The results in terms of the antenna size and radiation performance are addressed, and compared to measurements and previously published data.

The objectives of this research work are to investigate, design and implement circularly-polarized antennas to be used for handheld satellite mobile communication and wireless sensor networks. Several antennas such as Quadrifilar Spiral Antennas (QSAs), two arm Square Spiral and stripline or coaxially-fed microstrip patch antennas are developed and tested. These antennas are investigated and discussed to operate at L band (1.61-1.6214GHz) and ISM band (2.4835-2.5GHz) A substantial size reduction was achieved compared to conventional designs by introducing special modifications to the antenna geometries. Most of the antennas are designed to produce circularly-polarized broadside-beam except for wireless sensor network application a circularly-polarized conical-beam is considered. The polarization purity and Specific Absorption Rate (SAR) of two dual-band antennas for satellite-mobile handsets next to the human head are investigated and discussed, using a hybrid computational method. A small distance between the head and the handset is chosen to highlight the effects of the relatively high-radiated power proposed from this particular antenna. A Genetic Algorithm in cooperation with an electromagnetic simulator has been introduced to provide fast, accurate and reliable solutions for antenna design structures. Circularly-polarized quadrifilar helical antenna handset and two air-dielectric microstrip antennas were studied. The capabilities of GA are shown as an efficient optimisation tool for selecting globally optimal parameters to be used in simulations with an electromagnetic antenna design code, seeking convergence to designated specifications. The results in terms of the antenna size and radiation performance are addressed, and compared to measurements and previously published data.

Dans les environnements militaires, et plus particulièrement dans le domaine terrestre, de nombreux systèmes radioélectriques HF (de 3 à 30 MHz), VHF (de 30 à 300 MHz) et UHF (de 300 à 3000 MHz) sont utilisés. Ces systèmes remplissent plusieurs fonctions (communication longue et courte distance, brouillage, radar, etc ...) et peuvent parfois cohabiter sur un même porteur. Ces différentes fonctions utilisent plusieurs antennes et augmentent les risques de surexposition électromagnétique des opérateurs. Des normes civiles et militaires proposent des limites sur les champs électromagnétiques appliqués et sur des grandeurs dosimétriques (débit d'absorption spécifique DAS, densité de courant et champs électriques internes) pour limiter ces risques entre 0 et 300 GHz. Ces travaux de thèse ont deux objectifs principaux. Le premier est d'étudier les normes civiles et militaires afin de comprendre comment elles ont été développées et si elles sont réellement adaptées aux fréquences HF et VHF. Le deuxième est de proposer et valider une nouvelle méthode de validation des produits radio Thales. Pour cela, nous caractérisons numériquement le comportement électromagnétique et thermique du corps humain lors d'une exposition électromagnétique en bandes HF et VHF. L'étude des couplages entre le corps et les champs électromagnétiques externes nous permet de proposer pour la première fois des formules calculant les DAS dans le corps d'un fantôme homogène à partir, soit des courants induits le long du corps pour une exposition quelconque, soit du champ électrique appliqué pour une exposition en onde plane. / In military environments, especially land field, high frequencies (HF, 3 - 30 MHz), very high frequencies (VHF, 30 - 300 MHz) and ultra high frequencies (UHF, 300 - 3000 MHz) have been used for long range and shortrange communications, for communication interference or for detection. To have all those functions on the same carrier, they require many antennas, therefore they are increasing the operator's electromagnetic overexposure risk. Civilian and military standards were published providing limits on external electromagnetic fields and dosimetric quantities (specific absortion rate SAR, current density and internal electric field) to limit this overexposure risk between 0 and 300 GHz. The PhD thesis project has two main objectives. First, civilian and military standards are studied to understand how they were developed and if they are really suited for HF and VHF frequencies. Second, a new validation method of Thales radio product is proposed and validated. This PhD thesis project have characterized numerically the human body electromagnetic and thermal behavior during electromagnetic exposure in HF and VHF. Then, by studying couplings between external electromagnetic fields, induced current and human body, formulas to calculate both whole-body averaged SAR and local SAR 10 g in homogeneous body are proposed for the first time.

The main objectives of this research are to investigate and design low profile antennas for mobile handsets applications using the balanced concept. These antennas are considered to cover a wide range of wireless standards such as: DCS (1710¿1880 MHz), PCS (1850¿1990 MHz), UMTS (1920¿2170 MHz), WLAN (2400¿2500 MHz and 5000 ¿ 5800 MHz) and UWB frequency bands. Various antennas are implemented based on built-in planar dipole with a folded arm structure. The performance of several designed antennas in terms of input return loss, radiation patterns, radiation efficiency and power gain are presented and several remarkable results are obtained. The measurements confirm the theoretical design concept and show reasonable agreement with computations. The stability performance of the proposed antenna is also evaluated by analysing the current distribution on the mobile phone ground plane. The specific absorption rate (SAR) performance of the antenna is also studied experimentally by measuring antenna near field exposure. The measurement results are correlated with the calculated ones. A new dual-band balanced antenna using coplanar waveguide structure is also proposed, discussed and tested; this is intended to eliminate the balanced feed network. The predicted and measured results show good agreement, confirming good impedance bandwidth characteristics and excellent dual-band performance. In addition, a hybrid method to model the human body interaction with a dual band balanced antenna structure covering the 2.4 GHz and 5.2 GHz bands is presented. Results for several test cases of antenna locations on the body are presented and discussed. The near and far fields were incorporated to provide a full understanding of the impact on human tissue. The cumulative distribution function of the radiation efficiency and absorbed power are also evaluated. / UK Engineering and Physical Sciences Research Council (EPSRC)

The fifth-generation (5G) wireless network has received a lot of attention from both academia and industry with many reported efforts. Multiple-input-multiple-output (MIMO) is the most promising wireless access technology for next-generation networks to provide high spectral and energy efficiency. For handheld devices such as smartphones, 2×2 MIMO antennas are currently employed in 4G systems and it is expected to employ a larger number of elements for 5G mobile terminals. Placing multiple antennas in the limited space of a smartphone PCB poses a significant challenge. Therefore, a new design technique using dual-polarized antenna resonators for 8×8 MIMO configuration is proposed for sub 6 GHz 5G applications. The proposed MIMO configuration could improve the channel capacity, diversity function, and multiplexing gain of the smartphone antenna system which makes it suitable for 5G applications. Different types of new and compact diversity MIMO antennas with Patch, Slot, and Planar inverted F antenna (PIFA) resonators are studied for different candidate bands of sub 6 GHz spectrum such as 2.6, 3.6, and 5.8 GHz. Unlike the reported MIMO antennas, the proposed designs provide full radiation coverage and polarization diversity with sufficient gain and efficiency values supporting different sides of the mainboard. Apart from the sub 6 GHz frequencies, 5G devices are also expected to support the higher bands at the centimeter/millimeter-wave spectrums. Compact antennas can be employed at different portions of a smartphone board to form linear phased arrays. Here, we propose new linear phased arrays with compact elements such as Dipole and Quasi Yagi resonators for 5G smartphones. Compared with the recently reported designs, the proposed phased arrays exhibit satisfactory features such as compact size, wide beam steering, broad bandwidth, end-fire radiation, high gain, and efficiency characteristics. The proposed 5G antennas can provide single-band, multi-band, and broad-band characteristics with reduced mutual coupling function. The fundamental characteristics of the 5G antennas are examined using both simulations and measurements and good agreement is observed. Furthermore, due to compact size and better placement of elements, quite good characteristics are observed in the presence of the user and the smartphone components. These advantages make the proposed antennas highly suitable for use in 5G smartphone applications. / European Union Horizon 2020 Research and Innovation Programme under grant agreement H2020-MSCA-ITN-2016 SECRET-722424