Transport properties of a standard compact - cassette tape system are measured and software techniques devised to configure a low - cost,direct digital recording system. Tape - velocity variation is typically ± 10% of standard speed over tape lengths of 5 µm.with occasional variations of ±40%. Static tape - skew can result due to axial movement of the tape reel when it spools.Dynamic tape skew occurs and is primarily caused by tape - edge curvature with a constant contribution due to the transport mechanism.Spectral skew components range from 0.32 Hz to 8 Hz with magnitude normally within one 10 kbit/ sec- bit cell.The pinch roller works against the friction of the tape guides to cause tape deformation.Average values of tape deformation are 0.67 µm,0.85 µm and 1.08 µm for C60,C90 and C120 tape respectively. Parallel,software encoding / decoding algorithms have been developed for several channel codes.Adaptive software methods permit track data rates up to 3.33 k bits/sec in a rnultitrack system using a simple microcomputer.For a 4 - track system,raw error rates vary from 10ˉ⁷ at 500 bits/sec/track to 10ˉ⁵ at 3.33 kbits/sec/track.Adaptive software reduces skew - induced errors by 50%.A skew - correction technique has been developed and implemented on an 8 - track system at a track data rate of 10 k bits/sec. Real - time error correction gives a theoretical corrected error rate of 10ˉ¹¹for a raw error rate of 10ˉ⁷. Multiple track errors can cause mis - correction and interleaving is advised. Software algorithms have been devised for Reed - Solomon code. With a more powerful microprocessor this code m ay be combined with the above techniques in a layered error-correction scheme. The software techniques developed may be applied to N tracks with an N - bit computer.Recording density may be increased by using thin - film,multitrack heads and a faster computer.

International Telemetering Conference Proceedings / October 26-29, 1992 / Town and Country Hotel and Convention Center, San Diego, California / A Digital Output Recorder (DOR) system was developed by JAYCOR under contract to Defense Nuclear Agency (DNA) for the recording of high-speed digital data from test hardware exposed to radiation during an Underground Nuclear Test conducted at the Nevada Test Site (NTS) in 1991. Electronics hardware for the system is based on the well-supported Versa Module Europe (VME) bus which has become an industry standard for digital process and control systems. The system collects, identifies, and telemeters the data from several interfaces using the VME bus to a common data collection point above ground. The system was designed with built-in flexibility and expandability to meet digital data recording requirements on future underground tests (UGTs).

Shingled Magnetic Recording (SMR) has been recognised as one of the alternative technologies to achieve an areal density beyond the limit of the perpendicular recording technique, 1 Tb/in2, which has an advantage of extending the use of the conventional method media and read/write head. This work presents SMR system subject to both Inter Symbol Interference (ISI) and Inter Track Interference (ITI) and investigates different equalisation/detection techniques in order to reduce the complexity of this system. To investigate the ITI in shingled systems, one-track one-head system model has been extended into two-track one-head system model to have two interfering tracks. Consequently, six novel decoding techniques have been applied to the new system in order to find the Maximum Likelihood (ML) sequence. The decoding complexity of the six techniques has been investigated and then measured. The results show that the complexity is reduced by more than three times with 0.5 dB loss in performance. To measure this complexity practically, perpendicular recording system has been implemented in hardware. Hardware architectures are designed for that system with successful Quartus II fitter which are: Perpendicular Magnetic Recording (PMR) channel, digital filter equaliser with and without Additive White Gaussian Noise (AWGN) and ideal channel architectures. Two different hardware designs are implemented for Viterbi Algorithm (VA), however, Quartus II fitter for both of them was unsuccessful. It is found that, Simulink/Digital Signal Processing (DSP) Builder based designs are not efficient for complex algorithms and the eligible solution for such designs is writing Hardware Description Language (HDL) codes for those algorithms.

Ontario cage culture operations produce the majority of farmed rainbow trout in Canada, using a diverse range of management practices that are expected to result in substantial variation in trout performance across the industry. A preliminary survey of performance data was undertaken, resulting in data from 5 commercial sites between 2008 and 2012. Commercial performance was somewhat poorer than expected, particularly for mortality rates, thermal-unit growth coefficients, and economic feed conversion ratios (average weighted values of 12%, 0.165, and 1.36, respectively). Substantial variability in all performance parameters within and across operations suggests that continued production monitoring and benchmarking could be highly valuable for improving the economic sustainability of the sector. For future benchmarking efforts to be effective, improvement and standardization of data collection methods is needed. As such, a number of recommendations are provided to the industry for the refinement and standardization of performance recording protocols used by Ontario producers.

No description available.

No description available.

Made available in DSpace on 2014-10-09T12:34:19Z (GMT). No. of bitstreams: 0 / Made available in DSpace on 2014-10-09T14:10:09Z (GMT). No. of bitstreams: 0 / Dissertação (Mestrado) / IPEN/D / Instituto de Pesquisas Energeticas e Nucleares - IPEN-CNEN/SP

Made available in DSpace on 2014-10-09T12:34:19Z (GMT). No. of bitstreams: 0 / Made available in DSpace on 2014-10-09T14:10:09Z (GMT). No. of bitstreams: 0 / No início dos anos 90, os primeiros indícios do tráfico ilícito de materiais nucleares e radioativos foram observados principalmente na região européia. Uma década marcada por inúmeros casos de apreensão desse tipo de material. Como resultado, esses atos passaram a ser alvo de investigações criminais forenses, desenvolvendo-se a partir daí, a ciência forense nuclear. No Brasil não há registros oficiais do tráfico ilícito de material nuclear, entretanto, é amplamente conhecida a extração e o transporte ilegal de materiais geológicos radioativos, assim como a apreensão de fragmentos de materiais utilizados como blindagem de fontes radioativas. Uma das principais ferramentas utilizadas na ciência forense nuclear consiste no estabelecimento de bancos de dados de materiais nucleares. Esses documentos devem conter o maior número possível de informações sobre as características físicas, químicas e nucleares do material apreendido, permitindo a identificação de sua origem, processo de fabricação ou mesmo a idade (age). Assim, se estabelecem padrões de composição característicos de cada material, denominados assinaturas químicas (chemical finger print). Nesse trabalho foi adotado o protocolo forense nuclear seguindo as três etapas de avaliação sugeridas pela Agência Internacional de Energia Atômica (AIEA) na identificação da origem de Siliceto de urânio (U3Si2). Realizaram-se ensaios de caracterização física, química e isotópica dos materiais em estudo e compararam-se os dados com aqueles obtidos para outros compostos de urânio (Tetrafluoreto de urânio, UF4; óxidos de urânio, UO2 e U3O8; tricarbonato de amônio e uranila, TCAU) estabelecendo-se uma assinatura característica para cada um. A partir dos resultados foi possível classificar os compostos por grupos de origem, uma vez que são provenientes de diferentes processos de fabricação e/ ou origem. Demonstrou-se também a importância da criação e manutenção de um banco de dados nuclear na investigação de um evento forense nuclear. / Dissertação (Mestrado) / IPEN/D / Instituto de Pesquisas Energeticas e Nucleares - IPEN-CNEN/SP