This research addresses refractory forms of nitrogen that, even with advanced biological nitrification-denitrification systems are not removed completely from domestic wastewater. TKN (Total Kjeldahl Nitrogen), ammonia plus organic nitrogen, is one of the forms to measure the levels of nitrogen present in effluent wastewaters. Ferrate, a strong oxidant, was used for the treatment of these nitrogen forms with the objective of producing nitrogen compounds that can be removed by subsequent biological processes. Bench-scale experiments were performed on effluent samples taken prior to chlorination from an Orlando, FL wastewater treatment facility, using a biological nutrient removal process. The samples were treated with doses of ferrate ranging from 1 to 50 mg/L as FeO4–2 under unbuffered conditions. TKN removal as high as 70% and COD removal greater than 55% was observed. The TSS production after ferrate treatment was in a range of 12 to 200 mg/L for doses between 10 and 50 mg/L FeO4-2. After an optimum dose of ferrate was determined, three bench-scale reactors were operated under anoxic conditions for 10 to 12 days, two as duplicates containing the treated effluent and one as a control with untreated sample. Two different doses of ferrate were used as optimum dose for these experiments, 10 and 25 mg/L as FeO4-2. The purpose of these reactors was to determine the potential for biological removal of remaining nitrogen after ferrate oxidation of refractory nitrogen. Treated and raw samples were analyzed for Total Kjeldahl Nitrogen (TKN) (filtered and unfiltered), chemical oxygen demand (COD) (filtered and unfiltered), total suspended solids (TSS), nitrate (NO3-N), nitrite (NO2-N), and heterotrophic plate count (HPC). As a result, more than 70% of the soluble TKN was removed by chemical and biological oxidation for a sample treated with a dose of 25 mg/L FeO4-2, and less than 50% when treated with 10 mg/L FeO4-2. For the control samples run parallel to the ferrate treated samples, a maximum of 48% of soluble TKN and a minimum of 12% was removed. A three-log increase was observed in heterotrophic bacteria numbers for both doses during the operation of the reactors. Sodium ferrate was found to be an effective oxidant that can enhance the biodegradability of recalcitrant TKN present in municipal wastewaters. As mentioned before this research was develop using batch reactor units at bench-scale, therefore it is recommended to follow the investigation of the biodegradability of recalcitrant TKN of a ferrate treated sample under continuous flow conditions so that results can be extrapolated to a full-scale treatment facility.

Heavy metal contamination in water is a serious environmental and human health issue. Lead (Pb2+) and cadmium (Cd2+) are strictly regulated in wastewater effluent due to their high toxicity at low concentrations. Heavy metals are difficult to remove in conventional biological wastewater treatment because they are water soluble and non-biodegradable. Advanced treatment, such as tight membrane filtration and ion exchange, can be applied but they often require a high electrical energy input and a large amount of chemicals for pre- or post-treatment. Microbial electrolysis cells (MECs) can be used to treat wastewater while simultaneously recovering energy in the form of hydrogen gas. Additionally, MECs were proven to be effective for heavy metal removal. The commonly investigated removal mechanism for heavy metals in MECs is reduction at the cathode where heavy metal ions are reduced to metallic solids. The research presented in this thesis examined the effectiveness of cathodic reduction and other heavy metal removal mechanisms in MECs over a wide range of metal concentrations (10 μg/L-12 mg/L). Lab-scale MEC operation demonstrated successful removal of both Pb2+ and Cd2+ under different electric conditions, operation times, and initial metal concentrations. In addition to cathodic reduction, heavy metal removal in MECs was demonstrated through chemical precipitation at the cathode and electrochemical reduction and biosorption at the bioanode. The results of this research also confirmed the importance of microbial activity at the bioanode to efficiently drive the removal mechanisms in MECs. / Thesis / Master of Applied Science (MASc)

No description available.

No description available.

Intensification refers to utilizing wastewater treatment processes that decrease chemical and energy demands, increase energy recovery, and reduce the process footprint (or increased capacity in an existing footprint) all while providing the same level of nutrient removal as traditional methods. Shortcut nitrogen removal processes; including nitrite shunt, partial nitritation/anammox, and partial denitrification/anammox, as well as low-carbon biological phosphorus removal, were critically-evaluated in this study with an overall objective of intensification of existing infrastructure. At the beginning of this study, granular sidestream deammonification was becoming well-established in Europe, but there was virtually no experience with startup or operation of these processes in North America. The experience gained from optimization of the sidestream deammonification moving bed biofilm reactor (MBBR) in this study, including the novel pH-based aeration control strategy, has influenced the startup procedure and operation of subsequent full-scale installations in the United States and around the world. Long startup time remains a barrier to the implementation of sidestream deammonification processes, but this study was the first to show the benefits of utilizing media with an existing nitrifying biofilm to speed up anammox bacteria colonization. Utilizing media with an established biofilm from a mature integrated fixed film activated sludge (IFAS) process resulted in at least five times greater anammox activity rates in one month than virgin media without a preliminary biofilm. This concept has not been testing yet in a full-scale startup, but has the potential to drastically reduce startup time. False dissolved oxygen readings were observed in batch scale denitrification tests, and it was determined that nitric oxide was interfering with optical DO sensors, a problem of which the sensor manufacturers were not aware. This led to at least one sensor manufacturer reevaluating their sensor design and several laboratories and full-scale process installations were able to understand their observed false DO readings. There is an industry-wide trend to utilize influent carbon more efficiently and realize the benefits of mainstream shortcut nitrogen removal. The A/B pilot at the HRSD Chesapeake Elizabeth Treatment provides a unique chance to study these strategies in a continuous flow system with real wastewater. For the first time, it was demonstrated that the presence of influent particulate COD can lead to higher competition for nitrite by heterotrophic denitrifying bacteria, resulting in nitrite oxidizing bacteria (NOB) out-selection. TIN removal was affected by both the type and amount of influent COD, with particulate COD (pCOD) having a stronger influence than soluble COD (sCOD). Based on these findings, an innovative approach to achieving energy efficient biological nitrogen removal was suggested, in which influent carbon fractions are tailored to control specific ammonia and nitrite oxidation rates and thereby achieve energy efficiency in the nitrogen removal goals downstream. Intermittent and continuous aeration strategies were explored for more conventional BNR processes. The effect of influent carbon fractionation on TIN removal was again considered, this time in the context of simultaneous nitrification/denitrification during continuous aeration. It was concluded that intermittent aeration was able to achieve equal or higher TIN removal than continuous aeration at shorter SRTs, whether or not the goal is nitrite shunt. It is sometimes assumed that converting to continuous aeration ammonia-based aeration control (ABAC) or ammonia vs. NOx (AvN) control will result in an additional nitrogen removal simply by reducing the DO setpoint resulting in simultaneous nitrification/denitrification (SND). This work demonstrated that lower DO did not always improve TIN removal and most importantly that aeration control alone cannot guarantee SND. It was concluded that although lower DO is necessary to achieve SND, there also needs to be sufficient carbon available for denitrification. While the implementation of full-scale sidestream anammox happened rather quickly, the implementation of anammox in the mainstream has not followed, without any known full-scale implementations. This is almost certainly because maintaining reliable mainstream NOB out-selection seems to be an insurmountable obstacle to full-scale implementation. Partial denitrification/anammox was proven to be easier to maintain than partial nitritation/anammox and still provides significant aeration and carbon savings compared to traditional nitrification/denitrification. There is a long-standing interest in combining shortcut nitrogen removal with biological phosphorus removal, without much success. In this study, biological phosphorus removal was achieved in an A/B process with A-stage WAS fermentation and shortcut nitrogen removal in B-stage via partial denitrification. / Doctor of Philosophy / When the activated sludge process was first implemented at the beginning of the 20th century, the goal was mainly oxygen demand reduction. In the past few decades, treatment goals have expanded to include nutrient (nitrogen and phosphorus) removal, in response to regulations protecting receiving bodies of water. The only practical way to remove nitrogen in municipal wastewater is via biological treatment, utilizing bacteria, and sometimes archaea, to convert the influent ammonium to dinitrogen gas. Orthophosphate on the other hand can either be removed via chemical precipitation using metal salts or by conversion to and storage of polyphosphate by polyphosphate accumulating organisms (PAO) and then removed in the waste sludge. Nitrification/denitrification and chemical phosphorus removal are well-established practices but utilize more resources than processes without nutrient removal in the form of chemical addition (alkalinity for nitrification, external carbon for denitrification, and metal salts for chemical phosphorus removal), increased reactor volume, and increased aeration energy. Intensification refers to utilizing wastewater treatment processes that decrease chemical and energy demands, increase energy recovery, and reduce the process footprint (or increased capacity in an existing footprint) all while providing the same level of nutrient removal as traditional methods. Shortcut nitrogen removal processes; including nitrite shunt, partial nitritation/anammox, and partial denitrification/anammox, as well as low-carbon biological phosphorus removal, were critically-evaluated in this study with an overall objective of intensification of existing infrastructure. Partial nitritation/anammox is a relatively new technology that has been implemented in many full-scale sidestream processes with high ammonia concentrations, but that has proven difficult in more dilute mainstream conditions due to the difficulty in suppressing nitrite oxidizing bacteria (NOB). Even more challenging is integrating biological phosphorus removal with shortcut nitrogen removal, because biological phosphorus removal requires the readily biodegradable carbon that is diverted. Partial denitrification/anammox provides a viable alternation to partial nitritation/anammox, which may be better suited for integration with biological phosphorus removal.

The study of nitrate utilization as the final electron acceptor in biological phosphorus removal systems was investigated. The objectives of the study were (1) to determine whether polyphosphate (polyP) microorganisms can use nitrate as the final electron acceptor, and (2) to evaluate and compare polyP accumulation in the biomass of the system using nitrate as the terminal electron acceptor to the system using oxygen as the terminal electron acceptor. Two lab-scale biological phosphorus removal systems were operated as the A/O Process under the same conditions except for the terminal electron acceptor involved. The first system, System I, was operated as an Anaerobic/Anoxic process and the other, System II, was operated as an Anaerobic/Anoxic process. Both systems were operated at a 5-day sludge age and the same nominal hydraulic retention time of 9.1 hours (2.9 hours anaerobic, 6.2 hours anoxic or aerobic). The sludge recycle flow rate was equal to the influent flow rate. The two systems were fed with the same domestic wastewater spiked with sodium acetate and potassium phosphate to give the wastewater a COD concentration of 300-400 mg/L and a phosphorus concentration of 13-14 mg/L as P. Nitrate was fed to the second reactor of System I, while the second reactor of System II was aerated. The results showed that polyP microorganisms can use nitrate as the final electron acceptor. In this research, the Anaerobic/Anoxic system removed more phosphorus (74 mg P/day) from solution than the Anaerobic/Aerobic system (64 mg P/day). The phosphorus content of the sludge in the Anaerobic/Anoxic system was greater than that of the Anaerobic/Aerobic system, i.e. 6.5% as compared to 5.6%. The above evidence strongly confirms that polyP microorganisms can use nitrate as the final electron acceptor and that excess biological phosphorus uptake occurs under anoxic condition. The implication is that COD stored in the anaerobic reactor can be used to simultaneously remove nitrogen and phosphorus, which can substantially reduce the amount of COD required for combined nutrient removal. / Master of Science

Bioelectrochemical systems (BES) is a platform technology that is able to realize versatile engineering functions and recover valuable resources in an energy-efficient manner. One of the potential applications of BES is to remove and recover nutrients simultaneously from nutrient-rich wastewater, such as digested manure from livestock. A four-chamber BES was developed and used in this study to explore the potential to remove and recover hexavalent Chromium from synthetic wastewater, and ammonia and phosphate from digested manure. The BES was able to achieve 99.6% removal of Chromium by membrane adsorption in 5 days but failed to recover in the concentration chamber. Nutrients were removed from the waste stream and recovered in the recirculated catholyte by the electrical field generated from the waste. The BES was demonstrated to achieve substantial COD removal, nutrients removal and recovery. On average, the removal efficiencies were about 50% for COD, 85% for NH4-N and 40% for PO4-P, and the concentration of NH4-N recovered in the catholyte was 670 mg/L after 5 cycles under an applied voltage of 0.8 V. PO4-P was not recovered in solution, probably because it has precipitated under the alkaline condition together with Mg2+ and Ca2+ concentrated in the catholyte. It was also demonstrated that nutrients removal and recovery depended on the current generation and were mostly completed at high current. To sum up, the BES was proven to be an effective and sustainable approach to remove and recover nutrients from digested manure. / Master of Science

Thesis advisor: Christopher S. Lee / Background: Genital hair removal is a popular practice in Westernized cultures and has been associated with the belief that removal is necessary for hygiene. A body of literature exists that has found that genital hair removal is associated with adverse health outcomes, including sexually transmitted infections (STIs). This dissertation aims to detail the history of the practice, why the hygiene belief exists, and to systematically review the existing literature that assesses genital hair removal and STIs. Methods: Historical, socio-cultural analysis from the feminist perspective was performed on the literature to outline why genital hair removal was adopted at a population level. The STI/genital hair removal literature was systematically reviewed and analyzed utilizing PRISMA guidelines. The data generated did not support meta-analysis. Results: Genital hygiene removal has been normalized in Westernized culture as a compulsory component of genital hygiene, particularly for women. Genital hair removal decreases pubic lice infestations. Genital hair removal increases the incidence of gonorrhea and chlamydia infections in women. The data does not support that genital hair removal is necessary for genital hygiene and may be harmful to genital health. Conclusions: Healthcare providers should ask about genital hair and genital hygiene practices when taking a sexual health or preventative care history. Health care providers can educate patients that genital hair removal is not necessary for genital health. New research inquiries on this topic must account for the normalization of the genital hygiene belief. / Thesis (PhD) — Boston College, 2024. / Submitted to: Boston College. Connell School of Nursing. / Discipline: Nursing.

The main objective of the research was to investigate the effect of influent organic compounds on the performance of biological nutrient removal system. To carry out the investigation, a pilot plant system was designed and constructed. The system was operated as a UCT process at an influent flow rate of 0.15 liters/minute and a sludge age of 13 days. The influent wastewater was domestic sewage. Excess biological phosphorus removal and steady-state conditions were established before making experimental measurements, or adding supplemental substrate. The effects of separate addition of formic, acetic, propionic, butyric, isobutyric, valeric, and isovaleric acid, plus glucose, addition on phosphorus release under anaerobic conditions, and phosphorus uptake under aerobic conditions, were studied. The effects of the organic acid additions on the removal of nitrogen and COD, and changes in SOUR, MLVSS, and metals such as iron, magnesium, calcium and potassium, were also studied. In all experiments, the specific substrate was added continuously to the first anaerobic reactor for three days at an influent concentration of 100 mg COD/liter. Samples were collected from each reactor at the end of the addition period and analyzed for orthophosphate, nitrate, nitrite, sulfate, volatile fatty acids, COD, MLVSS, pH and metals. All added substrates, except formic acid and dextrose, caused significant increases in phosphorus release in the anaerobic stage, and phosphorus uptake, in the aerobic stage, and consequently, an increase in phosphorus removal efficiency. The molar ratios of phosphorus release to volatile fatty acid added obtained for propionic acid, acetic acid, butyric acid, and valeric acid were 0.44, 0.77, 0.78, and 1.72 respectively. However, on a COD basis, the greatest ratios of mg phosphorus released to mg COD utilized was produced by the addition of acetic acid (0.37) and valeric acid (0.19). It was also found that the branched organic acids, isobutyric and isovaleric, caused more phosphorus release in the anaerobic stage and better phosphorus removal efficiencies as compared with the nonbranching forms of the same organic acids. The molar ratios of phosphorus release for these two acids were 0.8 and 2.3, respectively, and on a COD basis were 0.16 and 0.25. For engineering applications, it is suggested by this research that at least 20 mg COD equivalent of acetic acid is needed for the removal of I mg phosphorus. The results obtained by this investigation were consistent with the hypothesis proposed by Marais et al., 1983. The most recent biochemical models, proposed by Comeau et al., 1986 and Wentzel et al., 1986, were also tested using the data collected in the present investigation. Both models, in most cases, overestimated the ratios of phosphorus release to volatile fatty acid utilized. A speculative model for anaerobic metabolism by poly-p bacteria of volatile fatty acids which contain both odd and even numbers of carbon atoms was proposed. All added substrates produced no effect on both COD and TKN removals. Metal releases were found to correlate with the amount of phosphorus release. / Ph. D.

No description available.