No description available.

No description available.

No description available.

Yes / A compact dielectric resonator antenna (DRA) for wideband applications is proposed. Two cylindrical dielectric resonators which are asymmetrically located with respect to the center of a rectangular coupling aperture are fed through this aperture. By optimizing the design parameters, an impedance bandwidth of about 29%, covering the frequency range from 9.62 GHz to 12.9 GHz, and a gain of 8 dBi are obtained. Design details of the proposed antenna and the results of both simulation and experiment are presented and discussed.

A new passive treatment to reduce sound transmission into payload fairing at low frequency is investigated. This new solution is composed of optimally damped vibration absorbers (DVA) and optimally damped Helmholtz resonators (HR). A fully coupled structural-acoustic model of a composite cylinder excited by an external plane wave is developed as a first approximation of the system. A modal expansion method is used to describe the behavior of the cylindrical shell and the acoustic cavity; the noise reduction devices are modeled as surface impedances. All the elements are then fully coupled using an impedance matching method. This model is then refined using the digitized mode shapes and natural frequencies obtained from a fairing finite element model. For both models, the noise transmission mechanisms are highlighted and the noise reduction mechanisms are explained. Procedures to design the structural and acoustic absorbers based on single degree of freedom system are modified for the multi-mode framework. The optimization of the overall treatment parameters namely location, tuning frequency, and damping of each device is also investigated using genetic algorithm. Noise reduction of up to 9dB from 50Hz to 160Hz using 4% of the cylinder mass for the DVA and 5% of the cavity volume for the HR can be achieved. The robustness of the treatment performance to changes in the excitation, system and devices characteristics is also addressed. The model is validated by experiments done outdoors on a 10-foot long, 8-foot diameter composite cylinder. The excitation level reached 136dB at the cylinder surface comparable to real launch acoustic environment. With HRs representing 2% of the cylinder volume, the noise transmission from 50Hz to160Hz is reduced by 3dB and the addition of DVAs representing 6.5% of the cylinder mass enhances this performance to 4.3dB. Using the fairing model, a HR+DVA treatment is designed under flight constraints and is implemented in a real Boeing fairing. The treatment is composed of 220 HRs and 60 DVAs representing 1.1% and 2.5% of the fairing volume and mass respectively. Noise reduction of 3.2dB from 30Hz to 90Hz is obtained experimentally. As a natural extension, a new type of adaptive Helmholtz resonator is developed. A tuning law commonly used to track single frequency disturbance is newly applied to track modes driven by broadband excitation. This tuning law only requires information local to the resonator simplifying greatly its implementation in a fairing where it can adapt to shifts in acoustic natural frequencies caused by varying payload fills. A time domain model of adaptive resonators coupled to a cylinder is developed. Simulations demonstrate that multiple adaptive HRs lead to broadband noise reductions similar to the ones obtained with genetic optimization. Experiments conducted on the cylinder confirmed the ability of adaptive HRs to converge to a near optimal solution in a frequency band including multiple resonances. / Ph. D.

To support the large growth in wireless devices, such as personal data assistants (PDAs), wireless local area network (WLAN) enabled laptop computers, and intelligent transportation systems (ITS), the FCC allocated three high-frequency bands for unlicensed operation. Of particular interest is the 5-6 GHz Unlicensed National Information Infrastructure (UNII) band intended to support high-speed WLAN applications. The UNII band is further split into three smaller 100 MHz sub-bands: 5.15 - 5.25 GHz; 5.25-5.35 GHz; and 5.725-5.825 GHz. VCOs that can be switched between each of the three UNII sub-bands offer flexibility and optimum phase-locked loop (PLL) design versus non-switchable VCOs. This work presents switched-tank voltage controlled oscillators (VCOs) designed in Motorolaà ­s 0.18 à µm HIP6WRF BiCMOS process that could be used in multiband receivers covering the three UNII sub-bands. The first VCO was optimized for low power consumption. The VCO draws a total of 6.75 mA from a 1.8 V supply including buffer amplifiers. The VCO is designed with a switched-capacitor LC tank circuit that can switch to two center frequencies, 5.25 GHz and 5.775 GHz, with 200 MHz of varactor-supplied tuning range. The simulated output voltage swing is 2.0 V peak-to-peak and is kept constant between sub-bands by an active PMOS load integrated into the biasing circuitry. The second VCO was optimized for a high output voltage swing by replacing the current biasing circuit with a degenerating inductor. This design targeted three center frequencies, 5.2 GHz, 5.3 GHz, and 5.775 GHz, with 100 MHz of tuning range. This design has an output peak-to-peak voltage swing of 5.2 V but consumes an average of 16.5 mA from a 1.8 V supply. The two fabricated circuits exhibit tuning ranges similar to the simulated results; however, the center frequencies of each decrease due to interconnect parasitics there were unaccounted for in the designs. The measured center frequencies are 4.4 GHz and 5.37 GHz for the first design, and 4.4 GHz and 4.7 GHz for the second design (with one state inoperative due to a faulty switch). The phase noise of the fabricated VCO designs was limited primarily by the low quality factor (Q-factor) of the on-chip LC tank circuits. Oscillators referenced with high-Q off-chip components such as quartz crystal references and surface acoustic wave (SAW) resonators in a PLL can exhibit much improved performance; however, these off-chip components add packaging/assembly cost and higher bill of materials, impedance matching issues, and parasitics that can significantly affect performance for RF applications. Thus, there is tremendous incentive for integrating high-Q components on-chip with the eventual goal of consolidating all of the RF/analog/digital components onto a single wireless-enabled chip, commonly called RF system-on-a-chip (SoC). Microelectromechanical (MEM) resonators have received significant attention based on their ability to provide high on-chip Q-factors at RF frequencies using fabrication techniques that are compatible with modern IC processes. MEM resonators transduce electrical signals into extremely low-loss mechanical vibration and vice versa. Consequently, this thesis also describes the modeling, simulation, and fabrication of contour-mode disk-shaped MEM resonators. This resonator geometry is capable of providing high-Q oscillation at frequencies exceeding 1 GHz at sizes easily within the limits of modern photolithography techniques. Finite element analysis is used to predict the frequency response of disk resonators under various operating conditions and to determine variables that are most critical to the resonator design. A silicon-on-insulator (SOI) fabrication process for constructing the disk is also discussed. Finally, the possible future integration of MEM resonators with multiband VCOs in a common IC process is proposed. / Master of Science

The explosive growth in wireless communications has led to an increased demand for wireless products that are cheaper, smaller, and lower power. Recently there has been an increased interest in using CMOS, a traditional digital and low frequency analog IC technology, to implement RF components such as mixers, voltage controlled oscillators (VCOs), and low noise amplifiers (LNAs). Future mass-market RF links, such as BlueTooth, will require the potentially low-cost single-chip solutions that CMOS can provide. In order for such single-chip solutions to be realized, RF circuits must be designed that can operate in the presence of noisy digital circuitry. The voltage controlled oscillator (VCO), an important building block for RF systems, is particularly sensitive when exposed to an electrically noisy environment. In addition, CMOS implementations of VCOs have been hampered by the lack of high-quality integrated inductors. This thesis focuses on the design of a fully integrated 2.5 GHz LC CMOS VCO. The circuit is intended as a vehicle for future mixed RF/digital noise characterization. The circuit was implemented in a 0.35 μm single poly, 4 metal, 3.3 V, CMOS process available through MOSIS. The oscillator uses a complementary negative transconductance topology. This oscillator circuit is analyzed as a negative-resistance oscillator. Monolithic inductors are designed using full-wave electromagnetic field solver software. The design of an "inversion-mode" MOS (I-MOS) tuning varactor is presented, along with a discussion of the effects of varactor nonlinearity on VCO performance. I-MOS varactors are shown to have substantially improved tuning range (and tuning curve linearity) over conventional MOS varactors. Practical issues pertaining to CMOS VCO circuit design, layout, and testing are also discussed. The characterization of the VCO and the integrated passives is presented. The VCO achieves a best-case phase noise of -106.7 dBc/Hz at 100 kHz offset from a center frequency of 2.73 GHz. The tuning range is 425 MHz (17%). The circuit consumes 9 mA from a 3.3 V supply. This represents excellent performance for CMOS oscillator designs reported at this frequency. Finally, several recommendations for improvements in oscillator performance and characterization are discussed. / Master of Science

No / A small dielectric resonator antenna has been designed for ultra wideband (UWB) communication system applications. The antenna element is a rectangular low permittivity ceramic block, with a dielectric constant of 9.4, and the modified T-shaped feed network includes a 50 ohm microstrip line to achieve strong coupling, and some bandwidth enhancement. The antenna performance is simulated and measured over a frequency band extending from 3100 MHz to 5500 MHz; the impedance bandwidth over this interval is 55.8% with VSWR <; 2, making the antenna suitable for UWB applications.

Yes / Potential demodulating ability in biological tissue exposed to Radio Frequency (RF) signals intrinsically requires an unsymmetrical diode-like nonlinear response in tissue samples. This may be investigated by observing possible generation of the second harmonic in a cavity resonator designed to have fundamental and second harmonic resonant frequencies with collocated antinodes. Such a response would be of interest as being a mechanism that could enable demodulation of information-carrying waveforms having modulating frequencies in ranges that could interfere with cellular processes. Previous work has developed an experimental system to test for such responses: the present work reports an electric circuit model devised to facilitate calibration of any putative nonlinear RF energy conversion occurring within a nonlinear test-piece inside the cavity. The method is validated computationally and experimentally using a well-characterised nonlinear device. The variations of the reflection coefficients of the fundamental and second harmonic responses of the cavity due to adding nonlinear and lossy material are also discussed. The proposed model demonstrates that the sensitivity of the measurement equipment plays a vital role in deciding the required input power to detect any second harmonic signal, which is expected to be very weak. The model developed here enables the establishment of a lookup table giving the level of the second harmonic signal in the detector as a function of the specific input power applied in a measurement. Experimental results are in good agreement with the simulated results. / Engineering and Physical Science Research Council through Grant EP/E022936A

Yes / Millimetre-wave frequencies are promising for sensitive detection of glucose levels in the blood, where the temperature effect is insignificant. All these features provide the feasibility of continuous, portable, and accurate monitoring of glucose levels. This paper presents a metamaterial-inspired resonator comprising five split-rings to detect glucose levels at 24.9 GHz. The plexiglass case containing blood is modelled on the sensor's surface and the structure is simulated for the glucose levels in blood from 50 mg/dl to 120 mg/dl. The novelty of the sensor is demonstrated by the capability to sense the normal glucose levels at millimetre-wave frequencies. The dielectric characteristics of the blood are modelled by using the Debye parameters. The proposed design can detect small changes in the dielectric properties of blood caused by varying glucose levels. The variation in the transmission coefficient for each glucose level tested in this study is determined by the quality factor and resonant frequency. The sensor presented can detect the change in the quality factor of transmission response up to 2.71/mg/dl. The sensor's performance has also been tested to detect diabetic hyperosmolar syndrome. The sensor showed a linear shift in resonant frequency with the change in glucose levels, and an R2 of 0.9976 was obtained by applying regression analysis. Thus, the sensor can be used to monitor glucose in a normal range as well as at extreme levels. / This study is funded by Ministry of Higher Education (MoHE) Malaysia under Fundamental Research Grant Scheme Vot No. FRGS/1/2019/TK04/UTHM/02/13, and it is partially sponsored by Universiti Tun Hussein Onn Malaysia (UTHM).