Future Navy Capabilities indicate the need for a supersonic cruise missile. Thus the need exists for a low cost, light-weight, and efficient means of supersonic propulsion. NPS has been developing the Pulse Detonation Engine, which in theory has a thermodynamic efficiency greater than 50% as compared to 35% for state of the art constant-pressure cycles currently in use in gas turbines/ramjets/scramjets. Nonetheless, there are two major problems in the development of this engine. These are the increase of the propulsive efficiency by removing the oxygen-assisted initiator currently in use, and the reduction of internal total pressure losses caused by the highly constrictive internal flow-path geometry currently required to promote the deflagration to detonation transition (DDT). The aforementioned problems have been addressed and a viable design proposed through the implementation of a novel Transient Plasma Ignition system and a split-flow path engine geometry as described in this work. Future work will concentrate on the development of a performance measurement test rig to experimentally assess the designs presented herein. / US Navy (USN) author.

No description available.

No description available.

No description available.

Approved for public release, distribution unlimited / An existing freejet facility was upgraded and its range of operation extended into the high subsonic regime for operation as a test rig for the development of a combined-cycle, turbo-ramjet engine. A combustor was designed, developed, and tested as the afterburner for the turbo-ramjet engine. At subsonic speeds with the afterburner running, an increase in thrust of 40% was measured over the baseline turbojet running at 80% spool speed. A Computational Fluid Dynamics model of the flow through the shrouded turbojet engine was developed and successfully used to assist in predicting the bypass ratio of the engine at different Mach numbers. Numerous recommendations were made to improve the operation of the test rig, to improve the performance of the turbo-ramjet engine, and refine the numerical models. These recommended improvements will extend the present capabilities to design and analyze small combined cycle engines which have an application in unmanned aerial vehicles and missiles. / Lieutenant, United States Navy

To provide quality benchmark data (that can be used in numerical simulation comparisons) and to examine the effects of combustion on a typical ramjet engine flowfield, a water-cooled, stainless steel dump combustor model was developed. A two-component Laser Doppler Anemometer (LOA) was used to measure the mean and turbulent velocities in the axial and tangential directions and provide a comparison between combusting and isothermal flows. However, before any LOA measurements could be taken, the combustor had to be configured to run in a suitably stable mode. Stability was identified by the pressure spectra obtained under various running conditions using piezoelectric pressure transducers wired to a spectrum analyzer. Operational parameters such as fuel composition, fuel injection location, acoustic configuration, and equivalence ratio were varied until instabilities were minimized. The optimal configuration ran with upstream fuel injection (premixed mode) at the duct center line and an orifice plate installed immediately upstream of the fuel injectors, with propane as the fuel. Once stability was achieved, LOA data was taken. The results showed some significant differences between the reacting and nonreacting flows. The most significant effect was the difference between the inherent recirculation regions for each case. Combustion decreased the length of the region by approximately 50 percent, while increasing the maximum negative velocities. This made for a more compact, but stronger, recirculation region. Since the recirculation region acts as the main flame holder and is a major source of turbulence, the changes in this region significantly altered the dump combustor flowfield. / Master of Science

Jet-in-crossflow is an interaction between a fuel jet and air crossflow commonly found in jet engines. The crossflow is used to break up or atomize the fuel jet for downstream combustion. This interaction between fluids while at low speeds, is predictable, varies greatly at higher speeds. This investigation seeks to (1) create a mechanism for jet-in-crossflow, using mechanical pintles, that is independent of velocity to help increase the predictability and reliability of jet engines and (2) identify key design parameters that will lead to flow independence. Parameters investigated in this experiment include pintle height, angle, and percent of pintle coverage into the jet orifice. Pintles that covered 100 percent of the jet showed a strong deviation from the traditional interaction with no pintle. Relationships were also found between the angle, height, and penetration depth although none as ubiquitous as the jet coverage.

Cold flow inside a Solid Fueled Ramjet (SFRJ) is simulated using large eddy simulations (LES). A finite element method using a Discontinuous Galerkin bases has been implemented in the open-sourced multi-physics software SU2. Novel LES formulations of the fuel-gas boundary conditions and the heat release due to mixing are obtained using integration by parts over the discontinuous Galerkin bases. The Smagorisnki and wall-adapted subgrid stress model for the scalar variance have been implemented and investigated in twodimensions. Spectral Proper Orthogonal Decomposition is used to analyze CFD results to determine acoustic modes in the ramjet. Peak acoustic frequencies are compared between between numerical and experimental results. Comparisons are made between simulations performed with a 2D axisymmetric domain and full 3D domain. Cold-flow LES simulations show that there are two dominant acoustic modes (St ≡ f/f0 = {3, 18}) in the ramjet and their frequency appears to be invariant to the cavity configuration. The first peak corresponds to a longitudinal mode associated to the chamber fundamental oscillations (with length scale Lc). The second is characterized with radial fluctuations in the mixing chamber and features the maximum chamber radius of the ramjet as its scaling length. Mixed (radial and axial) modes in the intermediate frequency range reveal the effect of a slanted aft wall on the acoustics. Three-dimensional cold flow simulations predicted weak non-symmetric (azimuthal) modes. Hot-flow simulations show a substantial increase in the mean chamber pressure with the addition of the cavity, indicating that it enhances flame-holding in solid-fuel ramjets, in agreement with the experiments. The analysis of the ramjet acoustic modes shows the emergence of low frequency modes in the cavity cases, in agreement with the experiments. Using SPOD, these modes were associated with low frequency breathing of the recirculation region at the nozzle throat. Perturbations are localized in the throat region because of the Mach number pressure scaling. These modes do not seem to affect the pressure fluctuation and thus combustion in the chamber. Together with the emergence of low frequency vortical modes, the cavity supports a decrease in the high-wave number harmonics of the ramjet chamber acoustic mode. These fluctuations are supported by non-linear amplification of the fundamental mode, which is enhanced by the thermo-acoustic coupling. / Master of Science / Novel propulsion designs, such as solid fuel ramjets, present the opportunity of optimizing cavity shapes using additive manufacturing and three-dimensional printing to improve fuelair mixing and lowering the thermo-acoustic feedback. In this work a computational model for solid fuel ramjets is developed and applied to laboratory firing tests performed by Prof Young's group at the advanced propulsion laboratory at Virginia Tech. In order to capture the fine mixing scales a novel discretization of the reactive Navier-Stokes using discontinuous Galerkin bases is implemented in an open source CFD code popular with aerospace graduate students and researchers. Subgrid modelling is implemented to determine the effect of small scales on the PMMA combustion mechanism developed at Virginia Tech. Numerical methods are used to simulate the turbulent flow of air through an axisymmetric cavity.

Supersonic inlet starting by mass spillage is studied theoretically and numerically in the present thesis. A quasi-one-dimensional, quasi-steady theory is developed for the analysis of flow inside a perforated inlet. The theory results in closed-form relations applicable to flow starting by the mass spillage technique in supersonic and hypersonic inlets. / The theory involves three parameters to incorporate the multi-dimensional nature of mass spillage through a wall perforation. Mass spillage through an individual slot is studied to determine these parameters; analytical expressions for these parameters are derived for both subsonic and supersonic flow conditions. In the case of mass spillage from supersonic flows, the relations are exact. However, due to the complexity of flow field, the theory is an approximation for subsonic flows. Therefore, a correction factor is introduced which is determined from an empirical relation obtained from numerical simulations. / A methodology is also proposed to determine perforation size and distribution to achieve flow starting for a given inlet at a desired free-stream Mach number. The problem of shock stability inside a perforated inlet designed with the proposed method is also discussed. / The method is demonstrated for some test cases. Time-realistic CFD simulations and experimental results in the literature confirm the accuracy of the theory and the reliability of the proposed design methodology.

No description available.