Yes / IET Editorial: In the future communications will be pervasive in nature, allowing users access at the “touch of button” to attain any service, at any time, on any device. The future device design process requires both a reconfigurable RF front end and back end with high tuning speed, energy efficiency, excellent linearity and intelligence to maximise the “greenness” of the network. But energy efficiency and excellent linearity are the main topics that are driving the designs of future transceivers, including their efforts to minimise network contributions to climate changes such as the effect of CO2 emissions: the minimisation of these is a requirement for information and communication technology (ICT) as much as for other technologies. Recently, information and communication technologies were shown to account for 3% of global power consumption and 2% of global CO2 emissions, and hence far from insignificant. The approach towards energy conservation and CO2 reduction in future communications will require a gret deal of effort which should be targeted both at the design of energy efficient, low-complexity physical, MAC and network layers, while maintaining the required Quality of Service (QoS). There is also a need, in infrastructures, networks and user terminals, to take a more holistic approach to improving or achieving green communications, from radio operation, through functionality, up to implementation. The increasing demand for data and voice services is not the only cause for concern since energy management and conservation are now at the forefront of the political agenda. The vision of Europe 2020 is to become a smart, sustainable and inclusive economy, and as part of these priorities the EU have set forth the 20:20:20 targets, whereby greenhouse gas emissions and energy consumption should be reduced by 20% while energy from renewables should be increased by 20%.

No description available.

As wireless devices and radar systems become more ubiquitous, there is a growing need for wideband multi-standard RF-SOCs. To enable the advantages of multi-standard systems, reconfigurable RF front ends are needed. Because of the large number of RF signals in wideband systems, tunability and linearity become important parameters. Prior work has shown tunable LC filters to be advantageous in the microwave regime. A balanced-to-unbalanced (balun) transformation circuit is required to support the differential nature of a tunable LC filter. An active balun that also performs as a transconductor to drive the LC tank would relax the design requirement for the LNA and remove a passive balun that would have to precede the LNA. This thesis discusses the linearization of active baluns and presents a comparison between two 4 to 7 GHz tunable BPF designs with active baluns implemented in 0.18 μm SiGe BiCMOS technology. Fourth order filtering is achieved by subtracting two 2nd order LC-tanks. This approach allows 3-dB bandwidth to be tunable from 10% to 20%. In each design, a linearized input active balun is employed to drive the LC-tanks from a single-ended input while preserving noise figure and IIP3 performance. Two different linearization techniques are applied for the balun designs. Simulated NF ranges from 7.5 to 13 dB and IIP3 averages about 5 dBm with the peak value of 21 dBm. / Master of Science / As wireless devices and radar systems become more ubiquitous, there is a growing need for Radio Frequency (RF) integrated circuits that can support multiple frequency bands and standards. Because of the large number of RF signals, robust tunability and power handling of the electronics become important parameters. Power handling is important because the amplifier and the filter can generate distortions if the power going through them becomes too high. Prior work has shown integrated tunable inductor-capacitor (LC) resonance based filters to be advantageous in the microwave frequency regime compared to integrated switched capacitor based filters. A balancedto-unbalanced (balun) conversion of the RF signals is needed to support the differential nature of the LC resonators. This thesis discusses transistor-based balun designs that can be integrated into front-end LC filter chips. The goal is to reduce distortion in the filter under the present of large number of RF signals and to keep noise of the circuit in reasonable range. The designs are implemented in 0.18 μm SiGe BiCMOS integrated circuit technology and simulated in commercial computer aided design software; predicted performance is competitive with the state of the art. The fabricated chips will be characterized in future work.

No description available.