Raman biosensors are appealing for many biomedical applications, due to their accuracy and speed. In addition, Raman microscopy is a non-labeled imaging technique that offers chemical contrast based on Raman vibrational frequencies. However, the weak Raman signal represents a significant obstacle to using Raman in biological applications. The objective of my PhD research, presented in this thesis, is to enhance the Raman signal, thereby enabling it to be used in a wide variety of biomedical applications. More specifically, the research focuses on two different Raman signal enhancement techniques. The first is to improve the Raman signal using hollow-core photonic crystal fibers; this enhanced the Raman signal of ethanol 40 times. The second approach is by generating a coherent anti-Stokes Raman scattering (CARS) signal. We demonstrated CARS microscopy of myelin (lipid-rich) structures using a single femtosecond Ti:sapphire laser, and a photonic crystal fiber (PCF) with two closely lying zero dispersion wavelengths (ZDWs). Generating low noise supercontinuum (Stokes beam) out of two closely lying ZDW PCFs, enabled us to perform fast data acquisition (84 μs per pixel) CARS imaging using a homebuilt microscope. However, the application of this fiber is often limited to CARS imaging of molecular species with vibrations at wavenumbers ≥ 2000 cm−1 Raman shift. In addition, as it is not a polarization maintaining fiber, it cannot be used for polarization CARS microscopy. A polarization-maintaining PCF with two far-lying zero dispersion wavelengths offers important advantages for polarization CARS microscopy, and for CARS imaging in the fingerprint region. This PCF, though commercially available, has had limited use for CARS microscopy in the C-H bond region. The main problem is that the supercontinuum from this fiber is typically noisier than that from a standard PCF with two closely-lying zero dispersion wavelengths. To overcome this, we determined the optimum operating conditions for generating a low-noise supercontinuum out of a PCF with two far-lying zero dispersion wavelengths, in terms of the input parameters of the excitation pulse. We measured the relative intensity noise (RIN) of the Stokes and the corresponding CARS signal, as a function of the input laser parameters in this fiber. We demonstrated that the results of CARS imaging using this alternate fiber are comparable to those achieved using the standard fiber for input laser pulse conditions of low average power, narrow pulse width with a slightly positive chirp, and polarization direction parallel to the slow axis of the selected fiber. Finally, we demonstrated a novel fiber-delivered, portable, multimodal CARS exoscope, for minimally invasive in-vivo imaging of tissues. The device was based on a micro-electromechanical system-scanning mirror and miniaturized optics, and light delivery by photonic crystal fibre. A single Ti:sapphire femtosecond laser approach is used to produce CARS and two photon excitation fluorescent and second harmonic generation images of different samples using the new setup. The high resolution and distortion-free images achieved with various samples, particularly in the reverse direction (epi), successfully demonstrate proof of concept, and paves the way to minimally or non-invasive in vivo imaging. Moreover, combining this novel endoscope with a portable femtosecond fiber laser will accelerate delivering multimodal nonlinear imaging endoscopy/microscopy to clinical bed-side applications.

This work deals with the transmission of optical radiation modulated by a radio frequency signal through an optical fiber. Furthermore, it describes the principles of communication and area coverage. It points out the practical use of components located in the communication chain of this system. Explains the functionality of the properties and the division of individual components. It introduces the benefits and limitations of this system. It further describes the creation of a topology suitable for laboratory measurement of RoF technology. Provides experimental measurement of C-band parameters. Indicates the possible use of RoF technology using a wireless optical link. A part of the work is also a sample laboratory protocol.

L’objectif de ce travail de thèse est d’étudier des lasers semi-conducteur issus de la plateforme d’intégration III-V sur Si et présentant un faible bruit d’intensité relatif (RIN) pour le transport de signaux RADAR par voie optique. Nous cherchons à obtenir des lasers de comportement dynamique dit de «Classe A», i.e. avec une réponse dynamique sans oscillations de relaxation. Dans ce cas, il a été précédemment montré qu’un tel comportement dynamique présente un RIN limité au bruit de grenaille sur une large bande de fréquences et est obtenu quand la durée de vie des photons dans la cavité est grande devant la durée de vie des porteurs dans la zone active. La plateforme photonique sur silicium est alors intéressante car elle permet de réaliser des cavités longues grâce aux guides optiques offrant de faibles pertes de propagation, i.e. de l’ordre du dB/cm. En première approche, nous avons étudié des lasers dont la cavité de longueur centimétrique est composée d’une partie active fournissant le gain optique et d’une partie passive composée de guide en silicium à faibles pertes de propagation. Nous avons proposé différentes optimisations des pertes optiques intra-cavité ainsi que différentes solutions de filtrage spectral à grande finesse nécessaire à une oscillation laser monomode. La seconde approcheétudiée repose sur le filtrage du RIN d’un laser hybride de longueur millimétrique en exploitant les effets de saturation du gain optique dans un amplificateur optique à SC (SOA). Nous avons présenté un modèle décrivant les différents mécanismes altérant le bruit du laser amplifié par un SOA. Une étudeexpérimentale a permis de mettre en évidence la réduction du RIN d’un laser hybride III-V sur silicium, allant jusqu’à 15 dB pour des fréquences allant jusqu’à quelques GHz. La dernière approche explorée dans cette thèse repose sur la conception de lasers DFB hybride III-V sur silicium à très haut facteur de qualité. L’utilisation d’un réseau de Bragg à pas variable permet de réduire les pertes radiatives, usuellement importantes dans les lasers DFB, et d’obtenir une cavité de facteur de qualité de l’ordre de quelques millions. Un premier composant réalisé présente un facteur de qualité de 65 000. / The objective of the present thesis is to investigate new laser architectures with low Relative Intensity Noise (RIN) using the Silicon Photonics integration platform. We intend to reach “class-A” dynamics, in which relaxation oscillations are eliminated. In this conditions, lasers with class-A dynamics exhibit shot-noise limited RIN over a wide frequency bandwidth, typically from 100 MHz to 20 GHz. Such behaviour can be obtained with high-Q laser cavities, i.e with long cavities or with ultra-low losses cavities. The silicon photonics platform is a good candidate for the desired dynamical behaviour as it makes possible the implementation of long cavities (ten’s of cm) based on low losses silicon waveguides (dB/cm). Three different approaches have been considered in the present work. In the first approach, we have developed centimetre long lasers, consisting of an active section providing the optical gain coupled to a passive section made with low losses silicon waveguides. We proposed different approaches to optimize the intra-cavity optical losses, and different architectures of high finesse optical filters allowing simultaneously single-mode operation and high side mode suppression. The second approach consists on filtering the laser RIN by taking advantage of the coherent population oscillations effects in a SC Optical Amplifier (SOA). We proposed a model for describing the different mechanisms altering the RIN of the amplified laser. We demonstrated 15 dB RIN reduction for frequencies up to a few GHz, using a hybrid III-V on Si laser and a “classical” SOA. The last approach explored in the present thesis is based on the use of hybrid III-V on silicon DFB lasers with a high quality factor. Using Silicon Bragg grating with a variable pitch can reduce the radiative losses, usually important in DFB lasers. In this case, we can obtain optical cavities with few millions quality factor, leading to few ns photon lifetime. We realize a first design of Si Bragg grating with a Q factor of 65 000.