Thesis (Ph. D.)--Tulane University, 1977. / Vita: leaf 263. Includes bibliographical references (leaves 251-262). Includes discography (leaves 247-250).

This study was designed to evaluate the ability of vertical drains to prevent liquefaction and limit associated settlement. Drain performance was investigated using full-scale tests with vertical drains in liquefiable sand using a laminar shear box with acceleration time histories applied at the base. Performance of the sand box with drains in these tests was compared with performance of the sane box without drains in previous tests. The test data was also used to create case histories which can be used for further research and calibration of computer models. Although some investigations regarding vertical drains have been performed with centrifuge tests, no full-scale drain installation had been tested previously. Two drain geometries were investigated, first with drains spaced at 4 feet and second with drains spaced at 3 feet, to determine the effect of spacing on drain effectiveness.Sand was hydraulically placed at a relative density of about 40%. Sensors to monitor pore water pressure, settlement, lateral displacement, and acceleration were placed in the laminar shear box. Three rounds of testing were performed with each drain configuration. Each round consisted of three tests, with peak sinusoidal acceleration levels of 0.05g, 0.1g, and 0.2g respectively, with 15 sinusoidal cycles in each case. A cone penetration test sounding was performed between each round as well as before and after testing to characterize the soil properties for each round.Prefabricated drains were effective at reducing excess pore pressure generation during shaking and increasing the rate of dissipation immediately following the shaking. Liquefaction induced settlement was typically reduced by about 50% relative to tests without drains. These results are in good agreement with results from previous centrifuge testing. Drains spaced closer together reduced the excess pore pressure that generated during shaking and increased the rate of pore pressure dissipation relative to tests with drains spaced further apart, but post-liquefaction settlements were similar. As the soil became denser, settlement decreased significantly, as did the time for pore pressures to dissipate.

Pile foundations for bridges must often resist lateral loads produced by earthquakes and thermal expansion and contraction of the superstructure. Right-of-way constraints near bridge abutments are leading to an increased use of mechanically stabilized earth (MSE) walls below the abutment. Previous research has shown that lateral pile resistance can be greatly reduced when piles are placed close to MSE walls but design codes do not address this issue. A full-scale MSE wall was constructed and 24 lateral load tests were conducted on pipe, square and H piles spaced at distances of about 2 to 5 pile diameters from the back face of the wall. The MSE wall was constructed using welded-wire grid and ribbed strip inextensible reinforcements. This paper focuses on four lateral load tests conducted on steel pipe piles located behind a 20-ft section of MSE wall reinforced with welded-wire grids. Results showed that measured lateral resistance decreases significantly when pipe piles are located closer than about 4 pile diameters from the wall. LPILE software was used to back-calculate P-multipliers that account for the reduced lateral resistance of the pile as a function of normalized spacing from the wall. P-multipliers for this study were 0.95, 0.68, and 0.3 for piles spaced 4.3, 3.4 and 1.8 pile diameters from the wall, respectively. Based on results from this study and previous data, lateral pile resistance is relatively unaffected (p-multiplier = 1.0) for piles spaced more than approximately 3.9 pile diameters (3.9D) from the MSE wall. For piles spaced closer than 3.9D, the p-multiplier decreased linearly as distance to the wall decreased. P-multipliers were not affected by differences in reinforcement length to height (L/H) ratio or reinforcing type. Lateral pile loads induce tensile forces in the soil reinforcement such that, as pile load increases the maximum induced tensile force increases. Results also indicate that maximum tensile forces typically occurred in the soil reinforcement near the pile location. Past research results were combined with data from this study and a statistical regression analysis was performed using all data associated with welded-wire grid reinforcements. A regression equations was developed to predict the peak induced tensile force in welded-wire grids based on independent variables including lateral pile load, normalized pile distance (S/D), transverse distance (T/D), L/H ratio, and vertical stress. The equation has an R2 value of 0.79, meaning it accounts for approximately 79% of variation for all welded-wire grid reinforcements tested to date.

Thesis (M.A.)--East Tennessee State University, 2004. / Includes bibliographical references (leaves 105-113). Also available via Internet at the UMI web site.

Finite element modeling of laminar shear box testing that consisted of loose sand treated with large diameter prefabricated vertical drains (PVDs), was performed. The objective of the modeling was to evaluate the reliability of the computer program FEQDrain for predicting excess pore pressure ratios (Ru) at sites treated with prefabricated drains. FEQDrain was found to be capable of successfully modeling measured excess pore pressure ratio time histories from the laminar shear box experiment, as long as an appropriate combination of €˜number of equivalent cycles and €˜shaking duration was chosen, and sensitive parameters were in the range of measured values. Hydraulic conductivity, soil compressibility, and cycles to liquefaction are sensitive parameters and govern the computed Ru values.Modeling shows that the loading rate in the laminar shear box (15 cycles at 2 Hz) likely induced higher Ru values than would be expected in a typical earthquake event with a longer duration. The longer duration allows the drains to dissipate pore pressures and prevent liquefaction. The number of equivalent cycles and duration of shaking combinations recommended for various moment magnitudes in the FEQDrain user manual predict lower, but similar Ru versus time curves. Thus, suggesting that PVDs would be equally effective for any size earthquake. However, drains are most effective at preventing liquefaction when earthquake ground motions are long and uniform, rather than short and intense.Results from models in this study compare favorably with those from computer modeling performed by Howell et al. (2014). The individual hydraulic conductivity and compressibility values were different they were somewhat compensating. Similar Ru values can be modeled with different combinations of these parameters.Based on computer analyses, wick drains and 2€ diameter PVDs were found to be relatively ineffective for preventing liquefaction. However, 3€ diameter PVDs are fairly effective but can be overwhelmed during intense shaking. In contrast, 4€ diameter and larger PVDs are significantly more effective.

Finite element modeling of laminar shear box testing that consisted of loose sand treated with large diameter prefabricated vertical drains (PVDs), was performed. The objective of the modeling was to evaluate the reliability of the computer program FEQDrain for predicting excess pore pressure ratios (Ru) at sites treated with prefabricated drains. FEQDrain was found to be capable of successfully modeling measured excess pore pressure ratio time histories from the laminar shear box experiment, as long as an appropriate combination of ˜number of equivalent cycles and ˜shaking duration was chosen, and sensitive parameters were in the range of measured values. Hydraulic conductivity, soil compressibility, and cycles to liquefaction are sensitive parameters and govern the computed Ru values.Modeling shows that the loading rate in the laminar shear box (15 cycles at 2 Hz) likely induced higher Ru values than would be expected in a typical earthquake event with a longer duration. The longer duration allows the drains to dissipate pore pressures and prevent liquefaction. The number of equivalent cycles and duration of shaking combinations recommended for various moment magnitudes in the FEQDrain user manual predict lower, but similar Ru versus time curves. Thus, suggesting that PVDs would be equally effective for any size earthquake. However, drains are most effective at preventing liquefaction when earthquake ground motions are long and uniform, rather than short and intense.Results from models in this study compare favorably with those from computer modeling performed by Howell et al. (2014). The individual hydraulic conductivity and compressibility values were different they were somewhat compensating. Similar Ru values can be modeled with different combinations of these parameters.Based on computer analyses, wick drains and 2 diameter PVDs were found to be relatively ineffective for preventing liquefaction. However, 3 diameter PVDs are fairly effective but can be overwhelmed during intense shaking. In contrast, 4 diameter and larger PVDs are significantly more effective.

Liquefaction is a costly phenomenon where soil shear modulus degrades as the generation of excess pore pressures begins. One of the methods to mitigate liquefaction, is the use of prefabricated vertical drains. Prefabricated vertical drains provide a drainage path to effectively mitigate the generation of pore pressures and aid in shear modulus recovery. The aims of this study were to define shear modulus degradation vs. shear strain as a function of excess pore pressure ratio; define the effects of prefabricated vertical drains on the behavior of pore pressure generation vs. shear strain; and to define volumetric strain as a function of shear strain and excess pore pressure ratios. A large-scale laminar shear box test was conducted and measured on clean sands with prefabricated vertical drains spaced at 3-feet and 4-feet. The resulting test data was analyzed and compared to data without vertical drains. The results show the effect of increasing excess pore pressure ratios on shear modulus and curves where developed to encompass these effects in design with computer programing like SHAKE or DEEPSOIL. The data also suggests that prefabricated vertical drains effectively mitigate excess pore pressure build-up, thus increased the shear strain resistance before pore pressures were generated. Regarding volumetric strain, the results suggests that the primary factor governing the measured settlement is the excess pore pressure ratio. This indicates that if the drains can reduce the excess pore pressure ratio, then the resulting settlement can successfully be reduced during a shaking event. The curves for shear modulus vs. cyclic shear strain as function of pore pressure ratio were developed using data with high strain and small strain which leaves a gap of data in the cyclic shear strain range of 0.0001 to 0.01. Further large-scale testing with appropriate sensitivity is needed to observe the effect excess pore pressure generation on intermediate levels of cyclic shear strain.

Studies of seismic and impact loading on foundation piles is an important and a focused interest in the engineering world today. Because of seismic and other natural events are unpredictable, uncontrollable and potentially unsafe it is a vital study to understand the behavior and relationship structures in motion have on there foundation. Statnamic Loading has become a popular method of studying this relationship in a controlled environment. Two groups of 9 and 15 driven hollow pipe piles were tested in saturated clay at the Salt Lake City Airport in July of 2002. The 9-pile group (3x3 configuration) was separated at 5.65 pile diameters and the 15-pile group (3x5 configuration) was separated at 3.92 pile diameters. The testing consisted of five target deflections. Each target deflection consisted of 15 cyclic lateral static loadings and a 16th lateral statnamic load. This study focuses on the statnamic loading. Damping ratios ranged from 23 to 50 percent for the 15-pile group and 29 to 49 percent for the 9-pile group. Both pile groups increased in damping as the deflections increased. The optimized mass in motion for the entire system was found to be roughly 21,000kg for the 15-pile group and 14,000 kg for the 9-pile group. Stiffness for the 15-pile group started at 50kN/mm and ended at 21kN/mm. The 9-pile group ranged from 28kN/mm to 12kN/mm.

Numerical Analysis of Passive Force on Skewed BridgeAbutments with Reinforced Concrete WingwallsScott Karl SnowDepartment of Civil and Environmental Engineering, BYU Master of Science Historically bridges with skewed abutments have proven more likely to fail during earthquake loadings (Toro et al, 2013) when compared to non-skewed bridges (Apirakvorapinit et al. 2012; Elnashai et al. 2010). Previous studies including small-scale laboratory tests by Jessee (2012), large-scale field tests by Smith (2014), and numerical modeling by Shamsabadi et al. (2006) have shown that 45° skewed bridge abutments experience a reduction in peak passive force by about 65%. With numerous skewed bridges in the United States, this study has great importance to the nation's infrastructure.The finite element models produced in this study model the large-scale field-testing performed by Smith (2014), which was performed to study the significant reduction in peak passive resistance for abutments with longitudinal reinforced concrete wingwalls. The finite element models largely confirm the findings of Smith (2014). Two models were created and designed to match the large-scale field tests and were used to calibrate the soil parameters for this study. Two additional models were then created by increasing the abutment widths from 11 feet to 38 feet to simulate a two-lane bridge. The 45° skewed 11-foot abutment experienced a 38% reduction in peak passive resistance compared to the non-skewed abutment. In contrast, the 45° skewed 38-foot abutment experienced a 65% reduction in peak passive resistance compared to the non-skewed abutment. When the wingwalls are extended 10 feet into the backfill the reduction decreased to 59% due to the change in effective skew angle.The finite element models generally confirmed the findings of Smith (2014). The results of the 11- and 38-foot abutment finite element models confirmed that the wingwall on the obtuse side of the 45° skewed abutments experienced approximately 4 to 5 times the amount of horizontal soil pressure and 5 times the amount of bending moment compared to the non-skewed abutment. Increases in the pressures and bending moments are likely caused by soil confined between the obtuse side of the abutment and the wingwall.A comparison of the 11- and 38-foot 45° skewed abutment models showed a decrease in the influence of the wingwalls as the abutment widened. The wingwall on the acute side of the 38-foot abutment developed approximately 50% of the horizontal soil pressure compared to the 11-foot abutment. The heave distribution of the 11-foot abutment showed approximately 1- to 2-inches of vertical displacement over a majority of the abutment backwall versus more than half of the 38-foot abutment producing ½ an inch or less.

In Rhythm Changes: Jazz Rhythm in the African American Novel, I demonstrate how novelists from the Harlem Renaissance to the Black Arts Movement adapted jazz rhythm into literary form. In the prologue to Invisible Man, Ralph Ellison famously defines invisibility as a state of being “never quite on the beat.” Ellison frames the novel as a kind of translation of the “invisible” rhythm the narrator hears in Louis Armstrong, a syncopated rhythm rooted in Black aesthetic and cultural forms. “Could this compulsion to put invisibility down in black and white be thus an urge to make music of invisibility?” Ellison was not alone in this project. The writers I study all exemplify what Duke Ellington calls a “tone parallel”—the concept that literary form could reproduce or “parallel” the particularities of musical form. However, these writers find literary strategies to transcend parallelism, such that the lines between medium begin to touch. Considering devices that cut across music and literature—anaphora, antiphonal dialogue, polysyndeton, parataxis—I argue that novelists, not just poets, respond formally to the rhythmic concepts they hear on the bandstand, synthesizing these innovations with a broader literary tradition. Rudolph Fisher’s novel The Conjure-Man Dies brings the complex rhythmic sensibility of Louis Armstrong to detective fiction; Ann Petry’s The Street channels the rhythmic phrasing of Ethel Waters in a “novel of social criticism”; Ellison’s epic unfinished second novel follows the paratactic rhythm of the preacher and jazz trombonist; and Amiri Baraka’s The System of Dante’s Hell projects the rhythm of Sonny Rollins and Cecil Taylor onto Charles Olson’s “Projective Verse.” By finding the literary in the musical and vice versa, these novelist-experimenters move beyond Pater’s credo that all art aspires to the condition of music.