101 |
Evanescent wave fiber optic PH sensor in Biomedical ApplicationLIN, CHENG-KUO 03 September 2012 (has links)
People to feel more and more attention to health, the pursuit of high quality of life, biomedical sensing is one of the development of technology, person to understand the current state of health, currently known as blood sugar and blood pressure monitors, to track health status
of the instrument is obvious too inadequate, usually go to the hospital for examination, but it is quite time-consuming, ranging from a waste of time, so the immediate biomedical optical fiber sensor to do direction. Evanescent wave ways to do research for my use of the sensing material-specific dye, sensing agent in different situations will be absorbed to change the situation, the use of sol-gel method (Sol-Gel) to
coated with the specific dye, to make our fiber clothes (cladding), when the light in optical fibers, through the specific dye to change the energy of light in optical fibers.
|
102 |
Fabrication of Single Mode Buried Waveguides Based on Hybrid Sol-gel GlassesWu, Yu-zhi 16 June 2004 (has links)
In this paper, single mode buried optical waveguides based on hybrid sol-gel glasses and PECVD oxide were fabricated. Two different buried waveguide devices are investigated, and their optical characteristics are characterized. The first buried waveguide was obtained
by etching a shallow trench on SiON layer. Then sol-gel material used as the guiding layer was deposited onto the layer and cured in proper conditions. Finally, the waveguides were completed by coating a sol-gel top cladding layer onto the guiding layer. The propagation loss of the
waveguide is 0.59dB/cm at £f=1310nm.
The second buried waveguide was fabricated by etching a trench of 5£gm on SiON layer and then burying sol-gel material into the trench.Proximity printing was used to define the waveguide core on sol-gel films.The waveguide was packaged for measurement after coating a UV glue
on top of the core layer. The propagation losses of this waveguide device are 0.6dB/cm and 0.57dB/cm for TE and TM polarized lights. The coupling losses are 2.21dB and 2.41dB for TE and TM lights.
|
103 |
Hybrid Organic-Inorganic Optical Waveguides for Lightwave CommunicationLin, Jing-Yuan 14 June 2005 (has links)
Hybrid waveguides based on antiresonant reflecting optical waveguide (ARROW) structure on Si substrates is investigated. The core layer of the waveguide is separated from the Si substrate by interference cladding which consists of a high index first cladding layer and a low index second cladding layer. The Ta2O5 first cladding layer was grown by rf magnetron sputtering system. The SiON second cladding layer was deposited by plasma-enhanced chemical vapor deposition (PECVD) based on the reaction of SiH4/N2O mixtures. Typical propagation losses of the waveguides using this SiON material system are less than 0.15 dB/cm. The high quality cladding layers are prepared to form the Fabry-Perot cavities to ensure low loss operation of the ARROW device at antiresonant conditions.
Two methods were proposed to demonstrate the enormous applications of hybrid ARROW waveguides. First, polyimide/Ta2O5/SiON ARROWs were fabricated to achieve high extinction ratio waveguide polarizers. This is accomplished by tuning the operating point of the TM0 mode from antiresonant condition toward high-order antiresonance of the second cladding layer utilizing birefringence of the waveguide core. The measured extinction ratio and insertion loss of a 2-cm-long ARROW polarizer are 40 dB and 2.2 dB, respectively.
In addition, the temperature dependence of refractive index of organic-inorganic sol-gel glasses was measured by Mach-Zehnder interferometry using the ARROW waveguides. The Sol-gel/Ta2O5/SiO2 ARROWs were fabricated to characterize index-to-temperature coefficients (dn/dT) of the sol-gel glasses because the optical confinement factor of the ARROW is very close to 1. The measured index-to-temperature coefficients of the sol-gel glasses with different compositions are negative and are on the order of 10-4.
|
104 |
Synthesis and Characterization of Unsaturated Polyester/Silica Hybrid Composites by Sol-Gel ProcessKa, Jhih-yao 08 July 2005 (has links)
The unsaturated polyester/silica hybrids have been synthesized via sol-gel process and characterized in an effort to obtain a transparent hybrid material in this study, with emphasis on the effects of silica precursors and coupling agents. Chemical properties, thermal properties, and morphology of the hybrids were investigated by Fourier-transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA), and scanning electron microscopy (SEM).
The results showed that silica particles can be dispersed homogeneously in the UP matrix; also, physical and chemical interactions at the interface between UP and silica can be enhanced by adding coupling agents into the system. From the thermal and chemical properties measurement, the decomposition temperature of UP backbone and the heat distortion temperature (HDT) of UP/Silica hybrid were higher than pure UP.
Solvent-resistance of UP/Silica hybrid was also enhanced by adding coupling agents. A model illustrating the chemical and physical interaction at the interface due to the addition of coupling agents is proposed to explain the resulted obtained.
|
105 |
Development of inhibitors based on organic-inorganic hybrid materials via sol-gel processLi, Yi-chun 04 July 2006 (has links)
Oligomers of hard and soft segments of unsaturated polyesters (UP) were synthesized. They were blended in different ratios and cured with various amounts of styrene. Based on the criteria of tensile strength and strain, hard segment/soft segment (60/40 wt %) UPs containing 35 wt % and 45 wt % of extra amount of styrene were chosen for further studies. Inorganic-organic hybrid materials were prepared by incorporating tetraethoxysilane and poly(dimethylsiloxane) into the UP resins via the sol-gel process by changing the ratios of HCl/TEOS, H2O/TEOS, TEOS/PDMS and the reaction time. The specimens of these hybrid materials after curing were characterized using the tensile tester, rheometer, scanning electron microscope (SEM), 29Si-NMR and thermogravimeter. In the condition of HCl/TEOS molar ratio 0.07, H2O/TEOS molar ratio 4, TEOS/PDMS weight ratio 90/10 and the reaction time 3 hours, the results of 29Si-NMR, SEM and silicone mapping indicate that these silica gels with 3D network were well dispersed in the UP resins. These specimens had tensile strength of 512¡Ó16 kgf/cm2 and elongation of 11¡Ó4 % which are above the criteria of inhibitors. From the erosion testing, flame retardants was added unsaturated polyester and inorganic-organic hybrid materials that can help to resist heat flame, remain of a fire on the surface had the char forming.
|
106 |
Study of Sol-gel semiconductor material for TFTs applicationYu, Cheng-hong 18 July 2006 (has links)
ZnO (Zinc-oxide) is a wide bandgap (Eg~3.3 ev ) semiconductor material , it is transparent in the visible region of the spectra and therefore, also less light sensitive. ZnO-based TFT can increase the field mobility, improve the opening of AMLCD pixel and the problem of photo-excited leakage current. Here we demonstrate ZnO-based TFT which was fabricated by sol-gel material through spin-coating deposition method. The process of spin-costing deposition provides a more efficient way for depositing device components and low cost than vacuum techniques. In the experiment we controlled the conductive and carrier concentration by different annealing temperature and different annealing equipment for optimizing our device characteristic. The material analysis of ZnO film is discussed by FTIR, SEM, and n&k. The electrical characteristic was measured by the I-V measurement system.
|
107 |
The Properties of Sol-Gel Derived Magnesium Modified Lead Titanate Pyroelectric Thin Film DetectorsKao, Ming-Cheng 16 June 2000 (has links)
The Mg-modified lead titanate [(Pb1-xMgx)TiO3,abbreviated to PMT] thin films were deposited on Pt/SiO2/Si substrates by spin coating with sol-gel processing in this thesis. 1,3 propanediol was used as solvent to minimize the number of cycles of spin coating and drying processes to obtain the desired thickness of thin film. By changing the Mg content (0~10 mol%) and the heating temperature (500~800¢J), the effects of various processing parameters on the thin films growth are studied. The effects of various Mg contents on the response of pyroelectric IR detector devices are studied also.
Experimental results reveal that the Mg contents will influence strongly on grain size, dielectricity, ferroelectricity and pyroelectricity of PMT thin films. With the increase of Mg content, the grain size of PMT thin film decrease slightly, and the lattice structure of PMT thin film will change from tetragonal to cubic when the Mg content over 8 mole%. The relative dielectric constant of PMT thin film increases from 25 up to 91. The tan
|
108 |
Thermal, Spectroscopic, and Morphological Analysis of Sol-gel-derived PMMA/Silica Hybrid CompositesChen, Jun-Guang 06 January 2003 (has links)
A series of PMMA/silica hybrid composites were prepared by a sol-gel process in different catalytic and drying. Their thermal properties were analysized by DSC and TGA, the micro-structures by SEM, and the chemical reactions by FTIR.
The highest decomposed temperature of these hybrid composites were found for samples prepared at low pH due to the hydrogen bonding. DSC data indicated the samples cured at 25 and 140 oC existed a higher Tg due to unhydrolyzed TEOS. The heat-treated hybrid composites exhibited more compact structures. The size of SiO2 particles from SEM increases with increasing drying temperature and pH value. The hybrid composites prepared in acid condition showed more Si-O-Si bonding than Si-O-C bonding in FTIR. In addition, in FTIR spectra the shifts have been observed from a non-hydrogen-bonded C=O at 1733cm-1 to a hydrogen-bonded carbonyl at 1725cm-1.
|
109 |
The Study of LiTaO3 Pyroelectric Thin Film IR Detectors Prepared by a Sol-Gel Method and Rapid Thermal Annealing TechnologyLi, Yi-Ju 16 July 2002 (has links)
The lithium tantalite [LiTaO3,abbreviated to LT] thin films were deposited on Pt/SiO2/Si substrates by spin coating with sol-gel processing and rapid thermal processing in this thesis. 1,3 propanediol was used as solvent to minimize the number of cycles of spin coating and drying processes to obtain the desired thickness of thin film. By changing the heating rate (600~3000¢J/min) and the heating temperature (500~800¢J), the effects of various processing parameters on the thin films growth are studied. The effects of various heating rate on the response of pyroelectric IR detector devices are studied also.
Experimental results reveal that the heating rate will influence strongly on grain size, dielectricity, ferroelectricity and pyroelectricity of LT thin films. With the increase of heating rate, the grain size of LT thin film decreases slightly, and the C-axis orientation is enhanced. The relative dielectric constant of LT thin film increases from 28 up to 45.6, the tand increases from 0.033 to 0.134, Ec increases from 122 KV/cm to 183 KV/cm, Pr increases from 7.45 mC/cm2 to 12.12 mC/cm2, and g increases from 9.33´10-9 C/cm2K up to 2.66´10-8 C/cm2K, respectively, as the heating rate increases form 600 up to 3000¢J/min. In addition, the results also show that the LT thin film possesses the largest figures of merit Fv (2.19¡Ñ10-10 Ccm/J) and Fm (4.01¡Ñ10-9 Ccm/J) at the heating temperature of 700¢J and heating rate of 1800¢J/min. The voltage responsivities (Rv) measured at 80 Hz increase from 5496 to 8455 V/W and the specific detecivities (D*) measured at 300 Hz increase from 1.94¡Ñ108 to 2.38¡Ñ108 cmHz1/2/W with an increase of heating rate from 600 to 1800¢J/min. However, the voltage responsivity and the specific detecivity decrease with heating rate in excess of 1800¢J/min. The results show that LT1800 pyroelectric thin film detector exists both the maximums of voltage responsivity and specific detecivity. Therefore, LT1800 thin film exhibits the best IR characteristics for detector material.
|
110 |
Production of cerium oxide microsheres by an internal gelation sol-gel processWegener, Jeffrey J. 14 January 2010 (has links)
The experiments performed for this research were completed to produce solid
cerium oxide microspheres by an internal gelation sol-gel process. The motivation for
this work was to develop a process that would enable the fabrication of a storage or
transmutation form for the plutonium and transuranics (TRU) from the Uranium
Extraction Plus (UREX ) used fuel reprocessing process. This process is being
investigated by the Department of Energy (DOE) and the Advanced Fuel Cycles
Initiative (AFCI) through the Nuclear Energy Research Initiative.
The internal gelation production of cerium oxide involves the combination of
hexamethylenetetramine (HMTA), urea, and cerium nitrate solutions at ~100oC.
Microspheres were produced by injection of a broth solution into a flowing stream of hot
silicone oil. The captured microspheres were aged, washed, and then underwent
Thermogravimetric Analysis (TGA), Differential Scanning Calorimetry (DSC), and XRay
Diffraction (XRD) analysis. The process variables examined in this study include
the concentrations of HMTA, urea and cerium nitrate, the process temperature, the postgelation
aging time, and the product washing conditions. Over a series of 70 experiments, it was determined that a broth solution
containing a mixture of 1.45 M cerium nitrate and 1.65 M HMTA and urea (1:1 ratio)
solutions produced the best cerium oxide microspheres. The spheres were aged for 30 to
60 minutes and then washed in hexane to remove the silicone oil and a subsequent series
of ammonium hydroxide washes to remove unreacted product and to fully gel the
microspheres.
Through DSC analysis it was determined that excess wash or unreacted product
may be removed by an exothermic reaction at approximately 200oC. The XRD analysis
of unheated spheres showed the presence of cerium oxide with additional cerium-bearing
organics. Following heating, the microspheres were completely converted to cerium
oxide.
|
Page generated in 0.0287 seconds