The possibility of commercial natural gas production from gas hydrates has been tested by researchers and industry for more than ten years. Depressurisation of gas hydrates in porous and permeable sandstones has successfully produced water and natural gas. However long term sustainable production is still elusive. Catastrophic sand production into the wellbore has terminated at least three of the significant depressurisation trials including the 2013 trial at the Daini-Atsumi knoll, Nankai Trough, offshore Japan. Sand production is generally thought to be the result of mechanical and hydrodynamic instability, however it appears the failure mechanism is not the same for all reservoirs and the location of reservoir porosity and pressure on the normal compression line for sands could be a controlling factor. Sand production in reservoirs at shallow depths and low confining stresses (less than 10 MPa) are likely to be influenced by fluid flow effects like those described by the Shields (1936) diagram. The relative density of the formation may also affect the nature of the sand production in these reservoirs. The Daini-Atsumi knoll is a structural high on the outer ridge of the Kumano forearc basin, offshore Japan. Hydrate saturations of 50 to 80 % occur within three geological units of the Middle Pleistocene Ogasa group. This group is made up of deep water sediments including sediment gravity flow deposits distinguished by alternating silt and sand layers. The presence of these alternating layers could have influenced the sand production seen during the trial. This reservoir heterogeneity at the 2013 Daini-Atsumi knoll gas hydrate production trial site was characterised using the descriptions of geological units, analogues and statistical techniques. Scenarios of this heterogeneity were tested in a high pressure plane-strain sand production apparatus. The results of these tests suggest the boundary shear stress of the fluid on the grains is a significant control on sand production for the Daini-Atsumi Knoll reservoir and the layering and grainsize structure of the sediments encourages sand production. Relative density of the sediments appears to impact the nature of the sand production where denser sediments show more localised movement. These results indicate that even minor weaknesses in sand control devices will result in uncontrollable sand production rates from the Daini-Atsumi Knoll gas hydrate reservoir. Managing the fluid flow rate in the reservoir and selectively completing coarser grained zones at the base of sand layers could help limit sand production in future trials.

A basin analysis was conducted at the Conway Flat coast (Marlborough Fault Zone, South Island, New Zealand) to investigate the interaction of regional and local structure in a transpressional plate boundary and its control on basin formation. A multi-tiered approach has been employed involving: (i) detailed analysis of sedimentary deposits; (ii) geomorphic mapping of terraces, fault traces and lineaments; (iii) dating of deposits by 14C and OSL and (iv) the integration of data to form a basin-synthesis in a sequence stratigraphy framework. A complex thrust fault zone (the Hawkswood Thrust Fault Zone), originating at the hinge of the thrust-cored Hawkswood anticline, is interpreted to be a result of west-dipping thrust faults joining at depth with the Hundalee Fault and propagating eastwards. The faults uplift and dissect alluvial fans to form terraces along the Conway Flat coast that provide the necessary relief to form the fan deltas. These terrace/fan surfaces are ~9 km long and ~3 km wide, composite features, with their upper parts representing sub-aerial alluvial fans. These grade into delta plains of Quaternary Gilbert-style fan deltas. Uplift and incision have created excellent 3D views of the underlying Gilbert-style fan delta complexes from topsets to prodelta deposits. Erosive contacts between the Medina, Rafa, Ngaroma and modern Conway fan delta deposits, coupled with changes in terrace elevations allow an understanding of the development of multiple inset terraces along the Conway Flat coast. These terraces are divided into five stages of evolution based on variations in sedimentary facies and geomorphic mapping: Stage I involves the uplift of the Hawkswood Range and subsequent increased sedimentation rate such that alluvial fans prograded to the sea to form the Medina fan delta Terrace. Stage II began with a period of incision, from lowering sea level or changes in the uplift and sedimentation rate and continued with the deposition of the Dawn and Upham fan deltas. Stage III starts with the incision of the Rafa Terrace and deposition of aggradational terraces in the upper reaches. Stage IV initiated by a period of incision followed by deposition of estuarine facies at ~8ka and Stage V began with a period of incision and continues today with the infilling of the incised valley by the modern fan delta of the Conway River and its continued progradation. New dates from within the Gilbert-type fan deltas along the Conway Flat coast are presented, using OSL and 14C dating techniques. Faulting at the Conway Flat coast began ~ 94 ka, based on the development of the Medina Terrace fan delta with uplift rates ~1.38~1.42 m/ka. The interplay of tectonics and sea level fluctuations continued as the ~79 ka Rafa Terrace fan deltas were created, with uplift rates calculated at ~1.39 m/ka. Detailed 14C ages from paleoforest (~8.4-~6.4 ka) in the Ngaroma Terrace and from the mouths of smaller streams have established uplift rates during the Holocene ~1-3 m/ka, depending on sea level.