No description available.

Energy harvesting is an interesting topic for today since we face running out of energy source, a serious problem in the world. Thermoelectric devices are a good candidate. They can convert heat (i.e. temperature gradient) to electricity. This result leads us to use them to harvest waste heat from engines or in power plants to generate electricity. Moreover, thermoelectric devices also perform cooling by applied voltage to device. This process is clean, which means that no greenhouse gases are emitted during the process. However, the converting efficiency of thermoelectrics are very low compare to a home refrigerator. The thermoelectric figure of merit (ZTm) is a number which defines the converting efficiency of thermoelectric materials and devices. ZTm is defined by Seebeck coefficient, electrical conductivity and thermal conductivity. To improve the converting efficiency, nanolaminated materials are good candidate.   This thesis studies TiN/ScN artificial nanolaminates, or superlattices were grown by reactive dc magnetron sputtering from Ti and Sc targets. For TiN/ScN superlattice, X-ray diffraction (XRD) and reciprocal space map (RSM) show that we can obtain single crystal TiN/ScN superlattice. X-ray reflectivity (XRR) shows the superlattice films have a rough surface, supported by transmission electron microscopy (TEM). Also, TiN/ScN superlattices grew by TiN as starting layer has better crystalline quality than ScN as starting layer. The electrical measurement shows that our superlattice films are conductive films.   Ca-Co-O system for inherently nanolaminated materials were grown by reactive rf magnetron sputtering from Ca/Co alloy target. The XRD shows we maybe get the [Ca2CoO3]xCoO2 phase, so far. The energy dispersive X-ray spectroscopy (EDX) reported that our films have Al conmination. We also discovered unexpected behavior when the film grown at high temperature showed larger thickness instead of thinner, which would have been expected due to possible Ca evaporation. The Ca-Co-O system requires further studies.

Global warming and developments of alternative energy technologies have become important issues nowadays. Subsequently, the concept of energy harvesting is rising because of its ability of transferring waste energy into usable energy. Thermoelectric devices play a role in this field since there is tremendous waste heat existing in our lives, such as heat from engines, generators, stoves, computers, etc. Thermoelectric devices can extract the waste heat and turn them into electricity. Moreover, the reverse thermoelectric phenomenon has the function of cooling which can be applied to refrigerator or heat dissipation for electronic devices. However, the energy conversion efficiency is still low comparing to other energy technologies. The efficiency is judged by thermoelectric figure of merit (ZT), defined by Seebeck coefficient, electrical conductivity and thermal conductivity. In order to improve ZT, thin film materials are good candidates because of their structural effects on altering ZT.    Ca3Co4O9 thin films grown by reactive radio frequency magnetron sputtering followed by post-annealing process is studied in this thesis. Structural properties of the films with the evolution of elemental ratio (Ca/Co) of calcium and cobalt have been investigated. For the investigations, three samples having elemental ratio 0.82, 0.72, and 0.66 for sample CCO1, CCO2 and COO3, respectively, have been prepared. Structural properties of the films have been investigated by X-ray diffraction (XRD) θ-2θ and pole figure analyses. Surface morphology of the films has been investigated by scanning electron microscopic (SEM) analyses. The highly oriented and phase pure epitaxial Ca3Co4O9 thin films were obtained in the end.   Mixing of ScN and CrN to obtain ScxCr1-xN solid solution thin films by DC magnetron sputtering is the other task in this thesis. Growth of ScN and CrN thin films were studied first in order to get the best mixed growth conditions. The phase shifts between ScN (111) and CrN (111) peaks were observed in mixed growth films by XRD θ-2θ measurements, indicating the formation of ScxCr1-xN. Surface morphology of the films were investigated by SEM. The (111)-oriented ScxCr1-xN thin films with decent surface smoothness grown by DC magnetron sputtering at 600 °C in pure nitrogen with bias were developed.

The electrical and thermal conductance and the Seebeck coefficient are calculated for one-dimensional systems, and their behavior as a function of temperature and chemical potential is investigated. It is shown that the conductances are proportional to an average of the transmission probability around the Fermi level with the average taken for the thermal conductance being over a wider range. This has the effect of creating less well-defined plateaus for thermal-conductance quantization experiments. For weak non-linearities, the charge and entropy currents across a quantum point contact are expanded as a series in powers of the applied bias voltage and the temperature difference. After that, the expansions of the Seebeck voltage in temperature difference and the Peltier heat in current are obtained. Also, it is shown that the linear thermal conductance of a quantum point contact displays a half-plateau structure, almost flat regions appearing around half-integer multiples of the conductance quantum. This structure is investigated for the saddle-potential model.

京都大学 / 新制・課程博士 / 博士(工学) / 甲第23512号 / 工博第4924号 / 新制||工||1769(附属図書館) / 京都大学大学院工学研究科電子工学専攻 / (主査)教授 白石 誠司, 教授 山田 啓文, 教授 引原 隆士 / 学位規則第4条第1項該当 / Doctor of Philosophy (Engineering) / Kyoto University / DGAM

No description available.

Os materiais cerâmicos termoelétricos preparados a partir de ligas de SiGe, são utilizados em Geradores de Potência a Radioisótopos (GTR), na conversão de energia por efeitos termoelétricos. Neste trabalho de pesquisa foram estudadas as condições de preparação destas cerâmicas a partir de ligas de Silício-Germânio. Visou-se, portanto obter a melhor eficiência, pela otimização da \"Fator de Mérito\" (ou Número de loffe) , através dos processos de preparação e tratamentos térmicos da liga, e também na dopagem das cerâmicas. As ligas de silício-germânio (Si80Ge20) foram obtidas pela técnica de crescimento Czochralski, com campo elétrico aplicado (ECZ) e também por outras técnicas de fusão e solidificação, para comparação. Amostras com homogeneidade satisfatória foram quebradas e moídas para processamento cerâmico. E em seguida o pó da liga foi então dopado, misturando-se este com pó de boro amorfo e depois prensado, a fim de se obter elementos cerâmicos semicondutores tipo-p, com propriedades termoelétricas para altas temperaturas (&#8776 1000&#176C). A sinterização foi feita por três técnicas diferentes: pela técnica dos Pós Discretos ou PIES (Pulverized and Intermixed Elements of Sintering), pelo procedimento cerâmico convencional, e pela Prensagem a Quente (HotPressing), sendo esta última usada como padrão de comparação. As amostras obtidas foram analisadas e caracterizadas por técnicas convencionais de caracterização cerâmica tais como: medidas da densidade, dos tamanhos dos grãos, porosidade, área superficial, etc. e também por medidas de alguns dos parâmetros físicos que influenciam diretamente na eficiência termoelétrica tais como: coeficiente Seebeck, calor específico e parâmetro de rede, para ligas de composição nominal Si80Ge20 sem e com dopantes para semicondutores tipo-p. Uma amostra preparada pela General Electric usando a técnica de Prensagem a Quente (Hot-Pressing), foi usada como padrão de comparação. A liga obtida pela técnica ECZ apresentou boa homogeneidade. Foi encontrado que a qualidade microestrutural das cerâmicas tais como: densidade, a regularidade e a composição química dos grãos das cerâmicas depende muito da técnica de processamento. Estes elementos cerâmicos termoelétricos poderão ser usados como fonte de energia em Geradores de Potência Termoelétrica a Radioisótopos (GTR) mais especificamente na alimentação de satélites brasileiros fabricados pelo Centro Técnico Aeroespacial (CTA) junto com o Instituto de Estudos Avançados (IEAv) através da Divisão de Energia Nuclear (IEAvENU) deste Instituto, ou entre outras aplicações para fins militares e civil / Doped ceramics elements, prepared from Si-Ge alloy are used in Radioisotopic Thermoelectric Generators (GTR) for energy conversion by thermoelectrical effects. In this research the experimentais conditions to prepare thermoeletric ceramics from Silicon-Germanium alloys have been determined. The purpose was to get the best efficiency, by optimization of the \"Merit Figure\" (or \"loffe Number\'), using different preparation methods and thermal treatments of alloys, as well as the doping of these ceramics. Silicon-Gemanium alloys (Si80Ge20) have been grown by the Czochralski technique under applied eletric field (ECZ) , as well as by others fusion techniques for comparison. Afier the fusion of the alloy, samples with satisfactory homogeneity have been smashed and milled for ceramic processing. Powder of Si-Ge alloy was then heavely doped by mixing with amorphous boron powder and pressed to get type-P semiconductor thermoelectrical ceramics elements, at high temperatures (&#8776 1000 &#176C). The sintering was made by three differents techniques: PIES method (Pulverized and Intermixed Elements of Sintering), convencional ceramic processing, and Hot-Pressing sintering, for comparison. The samples have been analyzed and characterized by conventional ceramics technique such as: determination of density, grain size, porosity, surface area, etc. and measuring toa some physical parameters that affect directly the thermoelectrical efficiency such as: Seebeck coefficient, specific heat and lattice parameter to Silicon-Germanium alloys with nominal composition Si80Ge20 with or without dopings to type-P semiconductors. A sample prepared by General Electric Company using the Hot-Pressing technique was used as standard. The alloy grown by ECZ technique showed a good homogeneity. It was found that the microstructural quality of the ceramics such as: density, grains regularity and chemical composition of the ceramics depend of the ceramic processing technique. These thermoelectrical elements can be used as power supply for the Brazilian satellites made by the Centro Técnico Aeroespacial (CTA) together with the Instituto de Estudos Avançados (IEAv) through the Divisão de Engenharia Nuclear (ENU) , and among other applications for military and civil purposes

No description available.

Submitted by Daniella Sodre (daniella.sodre@ufpe.br) on 2015-04-08T12:40:55Z No. of bitstreams: 2 DISSERTAÇÃO Gabriel Fonseca.pdf: 3837074 bytes, checksum: e2c9b20882785e374170658d648ee389 (MD5) license_rdf: 1232 bytes, checksum: 66e71c371cc565284e70f40736c94386 (MD5) / Made available in DSpace on 2015-04-08T12:40:55Z (GMT). No. of bitstreams: 2 DISSERTAÇÃO Gabriel Fonseca.pdf: 3837074 bytes, checksum: e2c9b20882785e374170658d648ee389 (MD5) license_rdf: 1232 bytes, checksum: 66e71c371cc565284e70f40736c94386 (MD5) Previous issue date: 2014-03-10 / Conselho Nacional de Desenvolvimento Científi co e Tecnol ógico; Coordenação de Aperfeiçoamento de Pessoal de Ní vel Superior; Financiadora de Estudos e Projetos; Fundação de Amparo a Ciência e Tecnologia do Estado de Pernambuco. / In this master thesis we study experimentally the longitudinal spin Seebeck effect (LSSE) in bilayers made of a ferromagnetic insulator (FMI) and a metallic layer (M). We also present a theoretical model based on the spin current density ⃗ Js carried by a non-equilibrium magnon distribution, generated by a thermal gradient ∇T across the thickness of the FMI. When ⃗ Js reach the FMI/M interface it is pumped towards the M layer due to conservation of the angular momentum, so, the M layer is essential for the LSSE existence. Here the FMI consists of a Yttrium Iron Garnet (YIG) lm, grown over a Gadolinium Gallium Garnet (GGG) substrate. Different metallic materials were used as the M layer i.e. Pt and Ta that have normal behavior and Py that is a ferromagnetic metal (FMM). The experimental procedure consists of systematic measurements of the electric voltage VISHE, produced by ⃗ Js through the Inverse Spin Hall Effect (ISHE) in the normal metal or (FMM) layer. In YIG/Pt measurements were done in the temperature range from 20 to 300 K. The experimental data are tted to the proposed model for the LSSE and good agreement is obtained. The results shows that the Py and Ta can be used to detect the LSSE with the ISHE. The results of this master thesis have strong interest in the area of spin caloritronics helping to the development of the eld and to raise possibilities of new spintronic devices. ----- Nesta diserta ção e estudado experimentalmente o Efeito Seebeck de Spin Longi- tudinal (LSSE), em bicamadas formadas por um isolante ferromagn etico (FMI) e um lme metalico (M). Tamb em foi desenvolvido um modelo te orico baseado na den- sidade de corrente de spin ⃗ Js que existe quando uma distribui c~ao de m agnons fora do equil brio e gerada por um gradiente t ermico ∇T aplicado na sec ção transversal do FMI. Quando ⃗ Js chega na interface FMI/M e bombeada para a camada M satis- fazendo a conserva ção do momentum angular, assim que a camada NM e essencial para ter um LSSE. Como camada FMI foi utilizada a granada de trio e ferro (YIG) crescida num substrato de (GGG). Diferentes materiais metalicos foram utilizados como camada M, sendo Pt e Ta paramagn eticos e o Py ferromagnetico. O proced- imento experimental consiste na medi c~ao sistem atica da voltagem el etrica VISHE, que e produzida por ⃗ Js por meio do efeito Hall de spin inverso (ISHE) que ocorre na camada M. As medidas em YIG/Pt foram feitas numa faixa ampla de temperatura de 20 a 300 K. Os dados experimentais são fi tados com a teoria proposta para o LSSE encontrando-se boa concordância. Nossos resultados mostram que o Py e o Ta s~ao bons candidatos para detec ção do LSSE. Esta disserta ção e de grande interesse na area da caloritrônica de spin, ajudando no desenvolvimento deste campo e na concep ção de novos dispositivos tecnol ogicos baseados na spintrônica.

Os materiais cerâmicos termoelétricos preparados a partir de ligas de SiGe, são utilizados em Geradores de Potência a Radioisótopos (GTR), na conversão de energia por efeitos termoelétricos. Neste trabalho de pesquisa foram estudadas as condições de preparação destas cerâmicas a partir de ligas de Silício-Germânio. Visou-se, portanto obter a melhor eficiência, pela otimização da \"Fator de Mérito\" (ou Número de loffe) , através dos processos de preparação e tratamentos térmicos da liga, e também na dopagem das cerâmicas. As ligas de silício-germânio (Si80Ge20) foram obtidas pela técnica de crescimento Czochralski, com campo elétrico aplicado (ECZ) e também por outras técnicas de fusão e solidificação, para comparação. Amostras com homogeneidade satisfatória foram quebradas e moídas para processamento cerâmico. E em seguida o pó da liga foi então dopado, misturando-se este com pó de boro amorfo e depois prensado, a fim de se obter elementos cerâmicos semicondutores tipo-p, com propriedades termoelétricas para altas temperaturas (&#8776 1000&#176C). A sinterização foi feita por três técnicas diferentes: pela técnica dos Pós Discretos ou PIES (Pulverized and Intermixed Elements of Sintering), pelo procedimento cerâmico convencional, e pela Prensagem a Quente (HotPressing), sendo esta última usada como padrão de comparação. As amostras obtidas foram analisadas e caracterizadas por técnicas convencionais de caracterização cerâmica tais como: medidas da densidade, dos tamanhos dos grãos, porosidade, área superficial, etc. e também por medidas de alguns dos parâmetros físicos que influenciam diretamente na eficiência termoelétrica tais como: coeficiente Seebeck, calor específico e parâmetro de rede, para ligas de composição nominal Si80Ge20 sem e com dopantes para semicondutores tipo-p. Uma amostra preparada pela General Electric usando a técnica de Prensagem a Quente (Hot-Pressing), foi usada como padrão de comparação. A liga obtida pela técnica ECZ apresentou boa homogeneidade. Foi encontrado que a qualidade microestrutural das cerâmicas tais como: densidade, a regularidade e a composição química dos grãos das cerâmicas depende muito da técnica de processamento. Estes elementos cerâmicos termoelétricos poderão ser usados como fonte de energia em Geradores de Potência Termoelétrica a Radioisótopos (GTR) mais especificamente na alimentação de satélites brasileiros fabricados pelo Centro Técnico Aeroespacial (CTA) junto com o Instituto de Estudos Avançados (IEAv) através da Divisão de Energia Nuclear (IEAvENU) deste Instituto, ou entre outras aplicações para fins militares e civil / Doped ceramics elements, prepared from Si-Ge alloy are used in Radioisotopic Thermoelectric Generators (GTR) for energy conversion by thermoelectrical effects. In this research the experimentais conditions to prepare thermoeletric ceramics from Silicon-Germanium alloys have been determined. The purpose was to get the best efficiency, by optimization of the \"Merit Figure\" (or \"loffe Number\'), using different preparation methods and thermal treatments of alloys, as well as the doping of these ceramics. Silicon-Gemanium alloys (Si80Ge20) have been grown by the Czochralski technique under applied eletric field (ECZ) , as well as by others fusion techniques for comparison. Afier the fusion of the alloy, samples with satisfactory homogeneity have been smashed and milled for ceramic processing. Powder of Si-Ge alloy was then heavely doped by mixing with amorphous boron powder and pressed to get type-P semiconductor thermoelectrical ceramics elements, at high temperatures (&#8776 1000 &#176C). The sintering was made by three differents techniques: PIES method (Pulverized and Intermixed Elements of Sintering), convencional ceramic processing, and Hot-Pressing sintering, for comparison. The samples have been analyzed and characterized by conventional ceramics technique such as: determination of density, grain size, porosity, surface area, etc. and measuring toa some physical parameters that affect directly the thermoelectrical efficiency such as: Seebeck coefficient, specific heat and lattice parameter to Silicon-Germanium alloys with nominal composition Si80Ge20 with or without dopings to type-P semiconductors. A sample prepared by General Electric Company using the Hot-Pressing technique was used as standard. The alloy grown by ECZ technique showed a good homogeneity. It was found that the microstructural quality of the ceramics such as: density, grains regularity and chemical composition of the ceramics depend of the ceramic processing technique. These thermoelectrical elements can be used as power supply for the Brazilian satellites made by the Centro Técnico Aeroespacial (CTA) together with the Instituto de Estudos Avançados (IEAv) through the Divisão de Engenharia Nuclear (ENU) , and among other applications for military and civil purposes