This study investigated a new approach to achieving high energy density supercapacitors (SCs) by using high surface area self-activated carbon from waste coffee grounds (WCGs) and modifying 3D printed electrodes' porous structure by varying infill density. The derived activated carbons' surface area, pore size, and pore volume were controlled by thermally treating the WCGs at different temperatures (1000˚C, 1100˚C, and 1200˚C) and post-treating with HCL to remove water-soluble ashes and contaminants that block activated carbon pores. Surface area characterization revealed that the carbon activated at 1000˚C had the highest surface of 1173.48 m2 g-1, and with the addition of HCL, the surface area increased to 1209.35 m2 g-1. This activated carbon was used for fabricating the electrodes based on the surface area and having both micropores and macropores, which are beneficial for charge storage. Direct ink writing (DIW) method was utilized for 3D printing SC electrodes and changing the electrode structure by increasing the infill densities at 30%, 50%, and 100%. Upon increasing the infill densities, the electrodes' mass increased linearly, porosity decreased, and the total surface area increased for the 30% and 50% infill electrodes but decreased for the 100% infill electrode. Cyclic voltammetry (CV) test on the assembled SC showed the highest specific capacitance and energy density of 5.81 F g-1 and 806.93 mWh kg-1 at 10 mV s-1, respectively, for the electrode printed at 50% infill density.

As part of the programme BA Forest Engineering at Hochschule WeihenstephanTriesdorf, University of Applied Sciences (HSWT), Department of Forestry we introduced a Forest Training Trail (FTT) to complement our curriculum with a strong focus on applied training in the field. The core of the FTT is (i) the trail itself with several sites with different focus and (ii) a questionnaire. Every semester a new trail at a new site within the training forest is set up. Usually, the trail encompasses four to six stations, each station representing a thematic focus of the training in the BA 'Forest Engineering', e.g. vegetation, silviculture, hunting, environmental protection, soil or other aspects. The students form teams of three and walk the FTT with a questionnaire and a map of the trail. After the deadline for handing in the questionnaires a master solution of the FTT is published on the faculty homepage in order to give students an opportunity for a self-feedback. The results of the regular evaluation show a high acceptance by the students. Our conclusion after four years of experience with the FTT is that the design as competition and game including a trophy resulted in a very high acceptance and participation with joy.

Self-activation is a process that takes advantage of the gases emitted from the pyrolysis process of biomass to activate the converted carbon. The pyrolytic gases from the biomass contain CO2 and H2O, which can be used as activating agents. As two common methods, both of physical activation using CO2 and chemical activation using ZnCl2 introduce additional gas (CO2) or chemical (ZnCl2), in which the CO2 emission from the activation process or the zinc compound removal by acid from the follow-up process will cause environmental concerns. In comparison with these conventional activation processes, the self-activation process could avoid the cost of activating agents and is more environmentally friendly, since the exhaust gases (CO and H2) can be used as fuel or feedstock for the further synthesis in methanol production. In this research, many types of biomass were successfully converted into activated carbon through the self-activation process. An activation model was developed to describe the changes of specific surface area and pore volume during the activation. The relationships between the activating temperature, dwelling time, yield, specific surface area, and specific pore volume were detailed investigated. The highest specific surface area and pore volume of the biomass-derived activated carbon through the self-activation process were up to 2738 m2 g-1 and 2.209 cm3 g-1, respectively. Moreover, the applications of the activated carbons from the self-activation process have been studied, including lithium-ion battery (LIB) manufacturing, water cleaning, oil absorption, and electromagnetic interference (EMI) shielding.