Land filling provides a major, safe, and economical disposal route for biosolids and sludges. With an expanding world, the demand for larger and higher capacity landfills is rapidly increasing. Proper analysis and design on such fills have pushed the boundaries of geotechnical engineering practice, in terms of proper identification and assessment of strength and deformation characteristics of waste materials. The engineering properties of Municipal Solid Waste (MSW) with co-disposal of biosolids and sludges with regards to moisture characteristics and geotechnical stability are of utmost importance. Significant changes in the composition and characteristics of landfill may take place with the addition of sludges and biosolids. In particular, the stability of waste slopes needs to be investigated, which involves the evaluation of the strength properties of the mixture of the waste and biosolids. This thesis deals with impact of the addition of biosolids on the geotechnical properties of class I landfill as determined from field investigations. The geotechnical properties are evaluated using an in-situ deep exploration test, called the Cone Penetration Test (CPT). CPT provides a continuous log of subsurface material properties using two measuring mechanisms, namely, tip resistance and side friction. The areas receiving biosolids are compared with areas without, to evaluate the effect of landfilling of biosolids. The required geotechnical shear strength parameters (angle of internal friction and cohesion) of MSW and biosolids mixture are determined by correlation with CPT results similar to the procedure followed in evaluating soil properties. The shear strength parameters obtained from the CPT data are then used to study the stability of different slope configurations of the landfill. The slope stability analysis is conducted on the various landfill models using the computer software SLOPE/W. This software was designed for soils but was found to be suitable for modeling landfills, as the waste is assumed to act similar to a cohesionless soil. Based on the field investigations, the angle of internal friction was found to be about 29° and the determination of any cohesion was not possible. It was concluded that the most suitable practical solution to adding biosolids into the landfill was in the form of trenches. From the slope stability study, it was found that the factor of safety reduces significantly with the introduction of biosolids due to a reduction in shear strength and increase in the overall moisture content. From a parametric study, the stability of a 1:2 side slope with an angle of friction lower than about 20° was found to be less than the safe limit of 1.5. In addition, the factors of safety for landfills with trenches extending close to the edges of the slopes were also found to be unsafe and this situation needs to be avoided in practice.

Yes / The test results on eight two-span deep beams made of self-compacting concrete (SCC) are presented and discussed in this paper. The main parameters investigated were the shear span-to-depth ratio, and the amount and configuration of steel reinforcement. All beams failed due to a major diagonal crack formed between the applied mid-span load and the intermediate support separating the beam into two blocks: the first one rotated around the end support leaving the other block resting on the other two supports. Both concrete compressive strength and web reinforcement had a major effect in controlling the shear capacity of the beams tested. For the shear span-to-depth ratio considered, the vertical web reinforcement had more influence on the shear capacity of the specimens than the horizontal web reinforcement. The shear provisions of the ACI 318M-11 are unconservative for most of the beams tested. Comparisons of test results with the strut-and-tie model (STM) suggested by ACI 318M-11, EC2 and CSA23.4-04 showed that the predictions are reasonable for continuous deep beams made with low and medium compressive strength. Although the equation suggested by ACI 318M-11 is very simple, its prediction is more accurate than the STM suggested by different design codes. / This research investigation was funded by the Higher Education Ministry in The Libyan Government.

yes / This paper reports the testing of fifteen reinforced concrete deep beams with openings. All beams tested had the same overall geometrical dimensions. The main variables considered were the opening size and amount of inclined reinforcement. An effective inclined reinforcement factor combining the influence of the amount of inclined reinforcement and opening size on the structural behaviour of the beams tested is proposed. It was observed that the diagonal crack width and shear strength of beams tested were significantly dependent on the effective inclined reinforcement factor that ranged from 0 to 0.318 for the test specimens. As this factor increased, the diagonal crack width and its development rate decreased, and the shear strength of beams tested improved. Beams having effective inclined reinforcement factor more than 0.15 had higher shear strength than that of the corresponding solid beams. A numerical procedure based on the upper bound analysis of the plasticity theory was proposed to estimate the shear strength and load transfer capacity of reinforcement in deep beams with openings. Predictions obtained from the proposed formulas have a consistent agreement with test results.

yes / Carpet waste fibres have a higher volume to weight ratios and once discarded into landfills, these fibres occupy a larger volume than other materials of similar weight. This research evaluates the efficiency of two types of carpet waste fibre as sustainable soil reinforcing materials to improve the shear strength of clay. A series of consolidated undrained (CU) triaxial compression tests were carried out to study the shear strength of reinforced clays with 1%, to 5% carpet waste fibres. The results indicated that carpet waste fibres improve the effective shear stress ratio and deviator stress of the host soil significantly. Addition of 1%, 3% and 5% carpet fibres could improve the effective stress ratio of the unreinforced soil by 17.6%, 53.5% and 70.6%, respectively at an initial effective consolidation stress of 200 kPa. In this study, a nonlinear regression model was developed based on a modified form of the hyperbolic model to predict the relationship between effective shear stress ratio, deviator stress and axial strain of fibre-reinforced soil samples with various fibre contents when subjected to various initial effective consolidation stresses. The proposed model was validated using the published experimental data, with predictions using this model found to be in excellent agreement.

Yes / Experimental study of five full scale masonry wall panels subjected to prescibed pre-compressive vertical loading and increasing in-plane lateral loading is discussed. All five walls were constructed using interlocking mortarless load bearing hollow concrete blocks. The behaviour of wall in term of deflections along the wall height, shear strength, mortarless joint behaviour and local and overall failures under increasing in-plane lateral loading and pre-compressive vertical loading are reported and analysed. Simple strut-and-tie models are also developed to estimate the ultimate in-plane lateral capacity of the panel walls tested. The results indicate that, as the pre-compressive load increases, the in-plane lateral load capacity of walls increases. All walls tested failed due to diagonal shear and/or moderate toe crushing depending on the level of the pre-compressive load. The proposed strut-and-tie models were able to give reasonable predictions of the walls tested.

To acquire deeper understanding and insights into the mechanical behaviour of fibre reinforced saturated/unsaturated cohesive soils, a programme of work was designed and included. 1) Conducting standard Consolidation Undrained (CU) tests to investigate mechanical behaviour of non-reinforced fully saturated soil. 2) Studying the strength of fibre reinforced clay though unconfined compression tests. 3) Testing the behaviour of unsaturated reinforced soil in unsaturated triaxial tests. 4) Determining the soil-water characteristic curves (SWCC) on soil sample with different fibre content. The investigation was undertaken on a clay of low plasticity index. Samples tested with addition of 1, 3 and 5 % fibre content and different values of matric suction of 50, 100 and 200 kPa, one of the challenges that were encountered in this research are how to prepare homogenous samples. A method for prepared compacted fibre reinforced soils with improved fibre distribution and density profile has been proposed and examined. The test results indicated that waste carpet fibres increase the shear strength of unsaturated clay soils. It was also found that relative increase in strength is also a function of applied suction. An increase in waste carpet fibres was found to reduce the hysteresis of soil. A data analysis conducted on the results of unsaturated tests as a function of fibre content and matric suction. The behaviour modelled was shown to be a perfect fit with the experimental data.

The shear stress in an unsaturated soil increases rapidly with limited shear strain to a peak value and then drops gradually with a further increase in the shear strain until a residual value is reached. In other words, there is a significant strain-softening behavior under large shear deformation. A variety of geotechnical structures (e.g., slopes, foundations, retaining walls and piles) associated with unsaturated soils typically undergo a large progressive deformation prior to reaching failure conditions due to the influence of environmental factors (e.g., rainfall infiltration and wetting-drying cycles). As a result, the shear strength of soils in sliding zones typically reduces from a peak to a residual value with the progressive development of large shear deformation, while the shear strength of soils in other zones are still at the peak level. In other words, in many scenarios the strain-softening behavior of unsaturated soils can significantly influence the mechanical behavior of geo-structures. Therefore, a thorough understanding of the shear strength behavior of unsaturated soils during strain-softening is required to reliably interpret the mechanical behavior of geo-structures that undergo large shear deformation. Significant advances have been made during the last thirty years to understand and model the strain-softening behavior of unsaturated soils. Most of these studies however focus on the strain-softening behavior within a relatively small shear deformation due to the limitations of the experimental apparatuses. Only limited experimental studies under large shear deformation were reported based on the modified suction-controlled ring shear apparatus. Therefore, more investigations are still required to provide a comprehensive understanding of the shear strength behavior of unsaturated soils during strain-softening under large shear deformation. Studies presented in this thesis are directed towards investigating the shear strength behavior of unsaturated soils during strain-softening and its application in geotechnical engineering practice. The following studies have been conducted: (i) A state-of-the-art review of the strain-softening behavior of unsaturated soils published in the literature during the past three decades is summarized. The physical mechanisms and modelling methods of the strain-softening behavior and the peak, critical and residual shear strength of unsaturated soils are investigated. (ii) A disturbed state concept model is proposed to predict the variation of shear stress in unsaturated soils during strain-softening process under drained condition. Five sets of experimental data gathered from the literature on unsaturated soils varying from coarse- to fine-grained soils are used to verify the proposed model. The proposed model can provide reasonable predictions for the strain-softening stress-strain relationships of various types of unsaturated soils. The model is simple in concept and all the required parameters can be obtained from conventional saturated and unsaturated shearing tests and pressure plate tests. (iii) Two sets of suction-controlled multistage ring shear tests are conducted on unsaturated SP-SM soil and Indian Head till (IHT), respectively. The variation of the shear stress, void ratio, and water content of specimens during shearing (the shear displacement reaches 100 mm) under multi levels of net normal stress and matric suction are described and discussed. The influence of matric suction and net normal stress on the residual shear strength envelops of unsaturated soils are critically discussed. (iv) A model for predicting the residual shear strength for a wide range of unsaturated soils comprising coarse- to fine-grained soils is developed in terms of two stress state variables (i.e., the net normal stress and matric suction) by using the soil water characteristic curve as a tool. The model is formulated and validated based on experimental data in a series of suction-controlled ring shear tests using the axis-translation technique, including the two sets of tests (SP-SM and IHT) conducted in this research and another three sets of tests (SM, SC-SM and CH) gathered from the literature. The fitting parameters are related to the plasticity index (Iₚ); thus, only four basic parameters (i.e., cᵣ', φᵣ', Sᵣ and Iₚ) are included in this approach. (v) A series of slope stability analyses of a landslide in unsaturated condition are conducted using Geoslope software based on the peak and residual shear strength parameters. The analyses results highlight the role of residual shear strength in the slope stability of unsaturated soils. In summary, the mechanical behavior of unsaturated soils under large shear deformation is comprehensively investigated in this thesis. The experimental results of the suction-controlled ring shear tests reported in this research contribute towards understanding the fundamental shear strength behavior of unsaturated soils during strain-softening under large shear deformation. The models proposed in this research provide simple tools to predict the shear strength of unsaturated soils under different levels of shear deformation.

The flexural behavior of a light-weight wood-based composite system was studied through destructive experiments. The composite panel system consisted of profiled dimensional lumber, which makes up the surface layers, and 1"-thick boards running across the surface layers. Considering the changes in cross-sections along the panel due to the presence of the embedded boards, classical theories such as the Euler-Bernoulli beam and Kirchhoff-Love plate could not be implemented. Instead, the deflections and maximum failure loads of the composite system under full- and short-span bending tests were measured during their destructive bending testing, and were compared against the mechanical properties of the conventional three-ply CLT panel with the same thickness as the panel with embedded cross-laminations. According to maximum failure loads and deflections, it was concluded that full-span panels with embedded cross-laminations exhibited higher strength and stiffness, whereas short-span panels exhibited higher strength and lower stiffness properties compared to conventional CLT panels.

No description available.

No description available.