<p>This thesis presents a palaeoglaciological study aimed to determine the location, geometry and temporal evolution of palaeo-ice streams of the north-easternmost Laurentide Ice Sheet. The work was accomplished through the geomorphological interpretation of satellite imagery over 3.19 x 10⁶ km² of the Canadian Arctic, using a glaciological inversion scheme. Ice streams were active in this region during most of the time between the Last Glacial Maximum and the last deglaciation. A web of ice streams and inter-ice stream areas existed. Three major ice stream networks are identified: the M'Clintock Channel, Gulf of Boothia – Lancaster Sound and Hudson Strait. The M'Clintock Channel bears the most complex landform record, comprising three generations of palaeo-ice streams. Their location was weakly controlled by the subglacial topography and their geometry was determined by frozen-bed portions of the ice sheet, thus providing evidence for pure ice streams in the Laurentide Ice Sheet. In contrast, the more pronounced relief of the Gulf of Boothia – Lancaster Sound corridor supported topographically controlled ice streams. The landform record on emerged land along Hudson Strait is insufficient to support the existence of ice streams. It is therefore proposed that ice streams were constrained within the deep parts of the strait while flanked by cold-based zones on the margins. Small transient ice streams on Baffin and Prince of Wales islands drained local remnant ice caps during the collapse of the ice sheet. Analysis of the controls on the location and flow of palaeo-ice streams suggests that the interaction between the subglacial topography and thermal state of the substrate plays a more fundamental role than the geology. It is concluded that the behaviour of ice streams cannot be explained in terms of environmental controls alone, but the complex dynamics of ice stream shear margins and onset zones must be considered.</p>

This thesis presents a palaeoglaciological study aimed to determine the location, geometry and temporal evolution of palaeo-ice streams of the north-easternmost Laurentide Ice Sheet. The work was accomplished through the geomorphological interpretation of satellite imagery over 3.19 x 106 km2 of the Canadian Arctic, using a glaciological inversion scheme. Ice streams were active in this region during most of the time between the Last Glacial Maximum and the last deglaciation. A web of ice streams and inter-ice stream areas existed. Three major ice stream networks are identified: the M'Clintock Channel, Gulf of Boothia – Lancaster Sound and Hudson Strait. The M'Clintock Channel bears the most complex landform record, comprising three generations of palaeo-ice streams. Their location was weakly controlled by the subglacial topography and their geometry was determined by frozen-bed portions of the ice sheet, thus providing evidence for pure ice streams in the Laurentide Ice Sheet. In contrast, the more pronounced relief of the Gulf of Boothia – Lancaster Sound corridor supported topographically controlled ice streams. The landform record on emerged land along Hudson Strait is insufficient to support the existence of ice streams. It is therefore proposed that ice streams were constrained within the deep parts of the strait while flanked by cold-based zones on the margins. Small transient ice streams on Baffin and Prince of Wales islands drained local remnant ice caps during the collapse of the ice sheet. Analysis of the controls on the location and flow of palaeo-ice streams suggests that the interaction between the subglacial topography and thermal state of the substrate plays a more fundamental role than the geology. It is concluded that the behaviour of ice streams cannot be explained in terms of environmental controls alone, but the complex dynamics of ice stream shear margins and onset zones must be considered.

No description available.

Contemporary observations show an increase in the melting of the Greenland Ice Sheet (GrIS) since the early 21st century. Located near the critical sites of oceanic deep convection and deep water formation, the melting of the GrIS has the potential to directly impact the Atlantic Meridional Overturning Circulation (AMOC) by freshening ocean surface waters in these regions. The majority of the Coupled Model Intercomparison Project Phase 5 (CMIP5) models project a decline in AMOC strength by 10-50% during the 21st century, in response to the increase in atmospheric greenhouse gas (GHG) concentrations. However, due to the simple treatment of polar ice sheets and the lack of a dynamical ice sheet component in these models, these projections likely underestimated the impacts of the GrIS melt, leading to uncertainty in projecting future AMOC evolution and climate change around Greenland. To better understand the impact of the GrIS melt on the AMOC, we perform a series of 21st century projection runs with a state-of-the-art Earth System Model-GFDL ESM2Mb. We consider a medium and a high Representative Concentration Pathway (RCP) scenario (RCP4.5 and RCP8.5, respectively). Unlike the CMIP5-standard RCP runs which included only radiative forcing, the new model experiments are also forced with additional and potentially more realistic meltwater discharge from the GrIS. This meltwater discharge is estimated based on a model-based relationship between the GrIS surface melt and the 500hPa atmospheric temperature anomalies over Greenland. The model simulations indicate that compared to the RCP4.5-only and RCP8.5-only projections, the additional melt water from the GrIS can further weaken the AMOC, but with a relatively small magnitude. The reason is that radiative forcing already weakens the deep convection and deep water formation in the North Atlantic, therefore limiting the magnitude of further weakening of AMOC due to the additional meltwater. The modeling results suggest that the AMOC's sensitivity to freshwater forcing due to the GrIS melt is highly dependent on the location and strength of oceanic deep convection sites in ESM2Mb as well as the pathways of the meltwater towards these regions. The additional meltwater contributes to the minimum surface warming (so-called "warming hole") south of Greenland. These simulations with ESM2Mb contribute to the Atlantic Meridional Overturning Circulation Model Intercomparison Project (AMOCMIP), a community effort between international modeling centers to investigate the impacts of the melting of the GrIS on the AMOC and quantify the associated uncertainty.

A blankholder is used to hold the edges of metal sheet while it is being formed by a matrix and a punch. An efficient way to design a stamping die is to integrate the blankholder plate into the die structure. This would eliminate the time and cost to manufacture blankholder plates. The integrated structure is called integrated blankholder. The main focus of this thesis is structural analysis and optimization of the integrated blankholder. The structural analysis of the integrated blankholder model (used for the production of doors of Volvo car model V70) is performed using Hypermesh and Abaqus. The FE-results were compared with the analytical calculations of the fatigue limit. To increase the stiffness and reduce the stress levels in the integrated blankholder, topology and shape optimization is performed with Optistruct. Thereafter, a CAD model is set up in Catia based on the results of optimization. Finally, structural analysis of this CAD model is performed and the results are compared with the original results. The results show reduction in stress levels by 70% and a more homogeneous stress distribution is obtained. The mass of the die is increased by 17 % and in overall, a stiffer die is obtained. Based on the simulations and results, discussion and conclusions are formulated.

No description available.

No description available.

No description available.

M.Ing. / To investigate the effect of plastic anisotropy in 1200H14 Aluminium sheet, simulations of the Swift Cupping Test were carried out using the finite element program ABAQUS. Anisotropy was built into all simulations based on the plastic strain ratio which was calculated from tensile tests on specimen cut in three directions in the plane of the sheet. Deep drawing tests were carried out using a punch and die sub-assembly as described by the Swift Cupping Test. Holder loads were kept constant while the punch load and displacement were recorded. Punch force-punch displacement curve and the formation of ears were compared with experimental results.

No description available.