The major cause of cracking in bridge decks, concrete pavements, as well as slabs on grade, is restrained shrinkage of the concrete. The resulting steel corrosion problem causes tremendous increase of maintenance and replacement cost. Shrinkage-compensating concrete (SHCC) and fiber-reinforced polymer (FRP) are explored to develop a hybrid slab system as one possible method of delaying the cracking and eliminating corrosion. To achieve the objective, a hybrid FRP reinforced SHCC structural system was developmed, and short-term and long-term behavior of this hybrid FRP-SHCC beams were investigated in this dissertation. In the first-stage development, a series of “coffee can” tests were carried out to measure and compare the expansion of SHCC from two candidate materials which were ettringite-system SHCC and lime-system SHCC. The selected SHCC candidate mix was then optimized to get the maximum expansion as well as a reasonable concrete strength. The optimized SHCC mix was used to make FRP-SHCC beams. The expansion of the concrete was measured through strain gauges on the FRP composite sheets during curing. Both glass FRP (GFRP) composite sheets and carbon FRP (CFRP) composite sheets were used for comparison. A series of third-point loading experiments were conducted to study the behavior of the proposed hybrid FRP-SHCC beams. In the second-stage development, long term prestress loss and static structural test of the proposed beams are investigated. Test results were evaluated based on maximum expansion strain, cracking load, crack width, load-deflection and ultimate load.The results indicate that the proposed system is promising in terms of its ability to develop a residual pre-stressing effect. Tests also show that the pre-stressing effect from the expansion of SHCC increases as the axial stiffness of the FRP reinforcement increases. A lime-system SHCC structural system shows higher prestress strain and less prestress loss than an ettringite-system SHCC system over the long term.

O objetivo desta tese foi o estudo da influência do aditivo redutor de retração (SRA) e o aditivo compensador de retração (SCA) em argamassas e pastas de cimento de escória ativada com silicato de sódio. A metodologia foi centrada na análise da retração por secagem e autógena, com o estudo de outras características que influenciam no fenômeno da retração, como as propriedades mecânicas. Para o avanço no conhecimento do efeito dos aditivos no comportamento do cimento de escória, foi caracterizada a microestrutura com a determinação da análise por termogravimetria, porosimetria e difração de raios X. Neste estudo foram empregados os seguintes teores de aditivo, porcentagem relativa à massa de aglomerante: 0,5%, 1%, 1,5% e 2% do aditivo SRA e 5%, 10% e 15% do aditivo SCA. Para a análise da influência da relação a/agl foram empregadas três teores: 0,40, 0,48 e 0,56. No estudo das amostras de referência, sem a utilização de aditivo, observou-se que o aumento da relação a/agl causa o aumento da retração por secagem e da retração autógena do cimento de escória ativada. A diminuição da resistência mecânica com o aumento da relação a/agl, o que torna o esqueleto sólido mais susceptível à deformações, e o aumento das tensões capilares, em razão do aumento da quantidade de água livre para ser evaporada, são os principais fatores para o aumento da retração por secagem. No caso da retração autógena, seu aumento é atribuído ao aumento da auto-secagem com o aumento do volume de poros com diâmetro na faixa de mesoporos, além da diminuição da resistência mecânica. O aditivo redutor de retração (SRA) conseguiu reduzir a retração por secagem em percentuais de 40% até 74% aos 28 dias, no entanto, este tipo de aditivo não obteve êxito no combate a retração autógena. Com relação à resistência mecânica, o aditivo SRA causou a redução de até 40%, efeito atribuído à diminuição do grau de hidratação e retardo do refinamento da porosidade. O aditivo compensador de retração (SCA) amenizou a retração por secagem e a retração autógena, reduzindo em até 64% e 70%, respectivamente, porém reduziu em até 60% a resistência mecânica do cimento de escória ativada. Com relação à microestrutura, o aditivo SCA diminuiu o grau de hidratação e aumentou a porosidade total, com o aumento da proporção do volume de macroporos. / The aim of this research was the study of the influence of shrinkage reducing admixture (SRA) and shrinkage compensating admixture (SCA) in mortars and pastes of blast furnace slag activated with sodium silicate. The method was centered in the analysis of free drying and autogenous shrinkage, with other characteristics that affect the shrinkage, as the mechanical properties. The microstructure behavior was accomplished with thermogravimetry (TG), mercury intrusion porosimetry (MIP) and X-ray diffraction (XRD). The samples were prepared with 0,5%, 1%, 1,5% and 2% of SRA admixture and 5%, 10% and 15% of SCA admixture, by binder mass. The effect of water/binder ratio was accomplished in three contents: 0,40, 0,48 and 0,56. In the reference mixtures, without admixtures, it was observed that an increase of water/binder ratio incurs in an increase of drying and autogenous shrinkage of alkali activated slag. The explanations for drying shrinkage behavior are the decrease of mechanical strength as consequence of water/binder increase, that turns the porous structure more susceptible to deformations, and the increase of the capillary tensions, attributed to the increase of free water to be evaporated. The increase of autogenous shrinkage with water/binder ratio is attributed to the increase of pore volume with diameter in the mesopores range, besides the decrease of the mechanical strength. The shrinkage reducing admixture (SRA) diminish drying shrinkage of 40% up to 74% at 28 days, however, this type of admixture was not capable to combat the autogenous shrinkage. About mechanical strength, the SRA admixture incurs in a decrease up to 40% of compression strength that it was attributed to the decrease of the hydration degree and retard of pore size refinement. The shrinkage compensating admixture (SCA) softened drying and autogenous shrinkage, reducing in up to 64% and 70%, respectively. However, the SCA admixture decreases in up to 60% mechanical strength of alkali activated slag. About microstructure, SCA admixture reduced the hydration degree and it increased the total porosity, with the increase of macropores volume.

O objetivo desta tese foi o estudo da influência do aditivo redutor de retração (SRA) e o aditivo compensador de retração (SCA) em argamassas e pastas de cimento de escória ativada com silicato de sódio. A metodologia foi centrada na análise da retração por secagem e autógena, com o estudo de outras características que influenciam no fenômeno da retração, como as propriedades mecânicas. Para o avanço no conhecimento do efeito dos aditivos no comportamento do cimento de escória, foi caracterizada a microestrutura com a determinação da análise por termogravimetria, porosimetria e difração de raios X. Neste estudo foram empregados os seguintes teores de aditivo, porcentagem relativa à massa de aglomerante: 0,5%, 1%, 1,5% e 2% do aditivo SRA e 5%, 10% e 15% do aditivo SCA. Para a análise da influência da relação a/agl foram empregadas três teores: 0,40, 0,48 e 0,56. No estudo das amostras de referência, sem a utilização de aditivo, observou-se que o aumento da relação a/agl causa o aumento da retração por secagem e da retração autógena do cimento de escória ativada. A diminuição da resistência mecânica com o aumento da relação a/agl, o que torna o esqueleto sólido mais susceptível à deformações, e o aumento das tensões capilares, em razão do aumento da quantidade de água livre para ser evaporada, são os principais fatores para o aumento da retração por secagem. No caso da retração autógena, seu aumento é atribuído ao aumento da auto-secagem com o aumento do volume de poros com diâmetro na faixa de mesoporos, além da diminuição da resistência mecânica. O aditivo redutor de retração (SRA) conseguiu reduzir a retração por secagem em percentuais de 40% até 74% aos 28 dias, no entanto, este tipo de aditivo não obteve êxito no combate a retração autógena. Com relação à resistência mecânica, o aditivo SRA causou a redução de até 40%, efeito atribuído à diminuição do grau de hidratação e retardo do refinamento da porosidade. O aditivo compensador de retração (SCA) amenizou a retração por secagem e a retração autógena, reduzindo em até 64% e 70%, respectivamente, porém reduziu em até 60% a resistência mecânica do cimento de escória ativada. Com relação à microestrutura, o aditivo SCA diminuiu o grau de hidratação e aumentou a porosidade total, com o aumento da proporção do volume de macroporos. / The aim of this research was the study of the influence of shrinkage reducing admixture (SRA) and shrinkage compensating admixture (SCA) in mortars and pastes of blast furnace slag activated with sodium silicate. The method was centered in the analysis of free drying and autogenous shrinkage, with other characteristics that affect the shrinkage, as the mechanical properties. The microstructure behavior was accomplished with thermogravimetry (TG), mercury intrusion porosimetry (MIP) and X-ray diffraction (XRD). The samples were prepared with 0,5%, 1%, 1,5% and 2% of SRA admixture and 5%, 10% and 15% of SCA admixture, by binder mass. The effect of water/binder ratio was accomplished in three contents: 0,40, 0,48 and 0,56. In the reference mixtures, without admixtures, it was observed that an increase of water/binder ratio incurs in an increase of drying and autogenous shrinkage of alkali activated slag. The explanations for drying shrinkage behavior are the decrease of mechanical strength as consequence of water/binder increase, that turns the porous structure more susceptible to deformations, and the increase of the capillary tensions, attributed to the increase of free water to be evaporated. The increase of autogenous shrinkage with water/binder ratio is attributed to the increase of pore volume with diameter in the mesopores range, besides the decrease of the mechanical strength. The shrinkage reducing admixture (SRA) diminish drying shrinkage of 40% up to 74% at 28 days, however, this type of admixture was not capable to combat the autogenous shrinkage. About mechanical strength, the SRA admixture incurs in a decrease up to 40% of compression strength that it was attributed to the decrease of the hydration degree and retard of pore size refinement. The shrinkage compensating admixture (SCA) softened drying and autogenous shrinkage, reducing in up to 64% and 70%, respectively. However, the SCA admixture decreases in up to 60% mechanical strength of alkali activated slag. About microstructure, SCA admixture reduced the hydration degree and it increased the total porosity, with the increase of macropores volume.

Abstract : Wastepaper sludge ash (WSA) is generated by a cogeneration station by burning wastepaper sludge. It mainly consists of amorphous aluminosilicate phase, anhydrite, gehlenite, calcite, lime, C2S, C3A, quartz, anorthite, traces of mayenite. Because of its free lime content (~10%), WSA suspension has a high pH (13). Previous researchers have found that the WSA composition has poor robustness and the variations lead to some unsoundness for Portland cement (PC) blended WSA concrete. This thesis focused on the use of WSA in different types of concrete mixes to avoid the deleterious effect of the expansion due to the WSA hydration. As a result, WSA were used in making alkali-activated materials (AAMs) as a precursor source and as a potential activator in consideration of its amorphous content and the high alkaline nature. Moreover, the autogenous shrinkage behavior of PC concrete at low w/b ratio was used in order to compensate the expansion effect due to WSA. The concrete properties as well as the volume change were investigated for the modified WSA blended concrete. The reaction mechanism and microstructure of newly formed binder were evaluated by X-ray diffraction (XRD), calorimetry, thermogravimetric analysis (TGA), scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDX). When WSA was used as precursor, the results showed incompatible reaction between WSA and alkaline solution. The mixtures were not workable and provided very low compressive strength no matter what kinds of chemical activators were used. This was due to the metallic aluminum in WSA, which releases abundant hydrogen gas when WSA reacts with strong alkaline solution. Besides, the results of this thesis showed that WSA can activate the glassy phase contained in slag, glass powder (GP) and class F fly ash (FFA) with an optimum blended ratio of 50:50. The WSA/slag (mass ratio of 50:50) mortar (w/b of 0.47) attained 46 MPa at 28 days without heat curing assistance. A significant fast setting was noticed for the WSA-activated binder due to the C3A phase, free lime and metallic aluminum contained in the WSA. Adding 5% of gypsum can delay the fast setting, but this greatly increased the potential risk of intern sulfate attack. The XRD, TGA and calorimetry analyses demonstrated the formation of ettringite, C-S-H, portlandite, hydrogarnet and calcium carboaluminate in the hydrated binder. The mechanical performance of different binder was closely related to the microstructure of corresponding binder which was proved by the SEM observation. The hydrated WSA/slag and WSA/FFA binder formed a C-A-S-H type of gel with lower Ca/Si ratio (0.47~1.6). A hybrid gel (i.e. C-N-A-S-H) was observed for the WSA/GP binder with a very low Ca/Si ratio (0.26) and Na/Si ratio (0.03). The SEM/EDX analyses displayed the formation of expansive gel (ettringite and thaumasite) in the gypsum added WSA/slag concrete. The gradual emission of hydrogen gas due to the reaction of WSA with alkaline environment significantly increased the porosity and degraded the microstructure of hydrated matrix after the setting. In the last phase of this research WSA-PC blended binder was tailored to form a high autogenous shrinkage concrete in order to compensate the initial expansion. Different binders were proportioned with PC, WSA, silica fume or slag. The microstructure and mechanical properties of concrete can be improved by decreasing w/b ratios and by incorporating silica fume or slag. The 28-day compressive strength of WSA-blended concrete was above 22 MPa and reached 45 MPa when silica fume was added. The PC concrete incorporating silica fume or slag tended to develop higher autogenous shrinkage at low w/b ratios, and thus the ternary binder with the addition of WSA inhibited the long term shrinkage due to the initial expansion property to WSA. In the restrained shrinkage test, the concrete ring incorporating the ternary binder (PC/WSA/slag) revealed negligible potential to cracking up to 96 days as a result of the offset effect by WSA expansion. The WSA blended regular concrete could be produced for potential applications with reduced expansion, good mechanical property and lower permeability. / Résumé : Les cendres de boues de désencrage (CBD) sont générées par une centrale de cogénération par combustion boues de désencrage. Ils se composent principalement de phase amorphe d'aluminosilicate, anhydrite, gehlenite, calcite, chaux, C2S, C3A, quartz, anorthite, des traces de mayénite. En raison de leur teneur en chaux libre (~ 10%), CBD ont un pH élevé (13). Les chercheurs précédents ont montré que la composition des CDB a une mauvaise robustesse et les variations conduisent à une certaine inconsistance pour le béton avec un mélange de ciment Portland (CP) et des CBD. Cette thèse a porté sur l'utilisation des CBD dans différents types de mélanges de béton pour éviter l'effet délétère de l'expansion due à l'hydratation des CBD. Par conséquent, les CBD ont été utilisées dans la fabrication des matériaux à activation alcaline (MAA), en tant que source précurseur et comme activateur potentiel en tenant compte de sa teneur en matière amorphe et la nature très alcaline des CBD. De plus, le retrait endogène du béton avec CP à faible rapport E/L a été utilisé afin de compenser l'effet d'expansion en raison des CBD. Les propriétés du béton ainsi que le changement de volume ont été étudiés pour le béton mélangé avec des CBD modifiés. Le mécanisme réactionnel et la microstructure du liant nouvellement formé a été évaluée par la diffraction aux rayons X diffraction (DRX), calorimétrie, l'analyse thermogravimétrique (ATG), microscopie électronique à balayage (MEB) et spectroscopie à dispersion d'énergie aux rayons X (DEX). Quand les CBD ont été utilisés comme précurseur, les résultats ont montré des réactions incompatibles entre CBD et une solution alcaline. Les mélanges ne sont pas maniables et donnent de très faibles résistances en compression, peu importe le type d'activateurs chimiques utilisés. Cela est dû à l'aluminium métallique dans les CBD, qui permet de libérer de l'hydrogène gazeux en abondance quand les CBD réagissent avec une solution alcaline forte. D'ailleurs, les résultats de ces recherches ont montré que les CBD peuvent activer la phase amorphe contenue dans le laitier, poudre de verre (PV) et les cendres volantes de classe F (CVF) avec un rapport de mélange optimal de 50:50. Un mortier avec un rapport massique 50:50 de CBD et de laitier (E/L de 0,47) atteint 46 MPa à 28 jours sans l’aide d’un murissement à chaud. Une prise rapide significative a été notée pour le liant CBD activé en raison de la phase C3A, chaux libre et l’aluminium métallique impliqué dans les CBD. L’ajout de 5% de gypse peut retarder la prise rapide, mais augmente grandement le risque potentiel de l’attaque au sulfate interne. Le DRX, ATG et l’analyse calorimétrique ont démontré la formation d'ettringite, C-S-H, la portlandite, hydrogrenat et carboaluminate de calcium dans le liant hydraté. Les différentes performances mécaniques du liant ont été étroitement liées à la microstructure correspondante qui a été prouvée par le MEB. Les liants hydratés CBD/laitier et CBD/CVF ont formé un type de gel C-A-S-H avec un faible rapport Ca/Si (0,47 ~ 1,6). On a observé un gel hybride (à savoir C-N-A-S-H) pour le liant CBD/PV avec un des très faibles rapports Ca/Si (0,26) et Na/Si (0,03). Les analyses MEB/DRX ont montré une formation de gel expansive (d’ettringite et de thaumasite) dans le gypse ajouté au béton avec les CBD et le laitier. L'émission progressive de l'hydrogène gazeux en raison de la réaction des CBD dans un environnement alcaline a augmenté la porosité et la dégradation de la microstructure de matrice hydratée après la prise. Dans la dernière phase de cette recherche, le liant avec un mélange de CBD et de CP a été développé pour former un retrait autogène élevé, afin de compenser l'expansion initiale. Différents liants ont été préparés avec le CP, CBD, la fumée de silice ou du laitier. La microstructure et les propriétés mécaniques du béton peuvent être améliorées en diminuant les rapports E/L et en incorporant la fumée de silice ou du laitier. La résistance en compression à 28 jours du béton aux CBD était supérieure à 22 MPa et atteint 45MPa lorsqu'on a ajouté de la fumée de silice. Le béton avec du CP incorporant de la fumée de silice ou du laitier ont tendance à développer un retrait endogène plus élevée à de faibles rapports E/L, et donc le liant ternaire avec l'ajout des CBD réduit le retrait à long terme en raison de la propriété d’expansion initiale des CBD. Dans l'essai de retrait empêché, l'anneau en béton incorporant le liant ternaire (CP/CBD/laitier) a révélé un potentiel négligeable à la fissuration jusqu'à 96 jours en raison de l'effet de décalage de l'expansion des CBD. Des liants modifiés avec des CBD peuvent être utilisés dans des mélanges de béton ordinaire pour des applications potentielles avec des expansions réduites, des bonnes propriétés mécaniques et une faible perméabilité.