Rutile powders in flaked form were pressed and heated at different temperatures (1000°C to 1300°C) under reducing (H₂/H₂O) atmospheres to study the rate of weight loss, the grain growth and the densification. The weight loss measurements for reduction of rutile to two non-stoichiometric compositions of TiO₁.₉₂ and TiO₁.₉₈ yielded an activation energy for weight loss of 82 ± 2 kcal/mole. No attempt was made to identify the rate-determining step. Previous weight loss measurements carried out in equilibrium conditions produced an enthalpy of 83 ± 10 kcal/mole for the formation of an oxygen ion vacancy. This could suggest that the rate-determining step might be the formation of an oxygen ion vacancy. The grain growth study revealed that the non-stoichiometric composition of TiO₁.₉₂ did not obey the theoretical relation of Burke. The results can be expressed by the following D² - D₀² = Kt°·⁶exp (- 78,000/RT) This activation energy for grain growth is equal to the activation energy for oxygen ion diffusion in TiO₂. This suggests that the oxygen ion diffusion may be the rate-controlling step for grain growth. The densification on sintering was evaluated from linear shrinkage measurements of the compacts during reduction to TiO₁.₉₂. A few models were tried, to find the best fit for the present data. While the photomicrographs suggest the Coble model for bulk diffusion, and the values for the diffusion coefficients are of the right order of magnitude, the activation energy for the rate determining step is about 118 kcal/mole, which is not in agreement with the previous sintering study on rutile. From grain growth data for those compacts reduced to TiO₁.₉₈ at 1200°C and those sintered in open air, it was seen that the diffusion coefficient was not significantly affected by variation of the oxygen partial pressure. This discrepancy in the activation energy value may be explained by a possible error in measurement and other unknown variables which may control the densification process. / Applied Science, Faculty of / Materials Engineering, Department of / Graduate

Os compósitos cerâmicos de alto desempenho têm sido objeto de frequentes estudos nas últimas décadas, visando à melhora das propriedades mecânicas e ao aumento da sua gama de aplicações em produtos tecnológicos. Este trabalho consistiu em estudar a preparação, a sinterização convencional e não convencional e as propriedades mecânicas e tribológicas resultantes de dois sistemas compósitos: t-ZrO2/Al2O3 e t-ZrO2/Al2O3-NbC. No sistema t-ZrO2/Al2O3 foram estudadas as composições de 0, 5 e 15% em volume de Al2O3 usando pós comerciais. No sistema t-ZrO2/Al2O3-NbC, foi usado um pó nanocristalino de Al2O3-NbC, obtido por moagem reativa de alta energia e adicionado na proporção de 5% em volume à matriz de t-ZrO2. Os pós foram prensados uniaxial e isostaticamente e sinterizados em forno convencional e pelas técnicas de flash sintering (FS) (t-ZrO2/Al2O3) e spark plasma sintering (SPS) (t-ZrO2/Al2O3-NbC). Os compósitos t-ZrO2/Al2O3 sinterizados convencionalmente e t-ZrO2/Al2O3-NbC sinterizados convencionalmente e por SPS foram caracterizados por medidas de densidade aparente, dilatometria, microscopia eletrônica de varredura (MEV), e medidas de propriedades mecânicas: dureza, módulo de Young e tenacidade à fratura. Os compósitos t-ZrO2/Al2O3 sinterizados por FS foram caracterizados por medidas de densidade aparente, dilatometria in situ e MEV. Os nanocompósitos de t-ZrO2/Al2O3-NbC foram também caracterizados quanto à resistência ao desgaste pelo método esfera-no-disco, utilizando esferas de Al2O3 e WC-6%Co como contramateriais. Os resultados mostraram que a moagem reativa de alta energia foi completa e efetiva na obtenção de pós nanométricos de Al2O3-NbC, com tamanhos de cristalito de 9,1 nm para Al2O3 e 9,7 nm para o NbC. A desaglomeração posterior à moagem de alta energia foi eficaz na redução do tamanho de aglomerados. Os compósitos t-ZrO2/Al2O3 e t-ZrO2/Al2O3-NbC sinterizados convencionalmente e ZrO2/Al2O3-NbC sinterizados por SPS mostraram alta densificação (>97% DT e boas propriedades mecânicas. Os nanocompósitos de t-ZrO2/Al2O3 sinterizados por FS apresentaram uma densificação ultrarrápida (< 1 min) com retração linear superior às amostras sinterizadas em forno convencional, ocorrente a temperaturas inferiores a 1000°C, com densidades relativas superiores a 90% DT em algumas composições. Os nanocompósitos de t-ZrO2/Al2O3-NbC apresentaram propriedades competitivas entre os compósitos sinterizados convencionalmente e por SPS, com dureza e tenacidade à fratura superiores às da t-ZrO2 monolítica. A resistência ao desgaste desses nanocompósitos sinterizados convencionalmente, no entanto, foi notadamente superior à dos sinterizados por SPS. A oxidação do NbC nos compósitos sinterizados convencionalmente influiu negativamente nas propriedades, levando à sugestão de uma \"janela\" de temperaturas em que a sinterização do nanocompósito de t-ZrO2/Al2O3-NbC seja interessante sem a degradação das propriedades mecânicas. Os resultados permitiram concluir que os materiais estudados apresentam potencial para aplicações industriais que requerem cerâmicas de alto desempenho mecânico e de resistência ao desgaste. / High performance ceramic composites have been the subject of frequent studies in recent decades, aiming at improving mechanical properties and increasing their range of applications in technological products. This work consisted in studying the preparation, the conventional and non-conventional sintering and the mechanical properties resulting from two t-ZrO2 matrix composites: the t-ZrO2/Al2O3 system and the t-ZrO2/Al2O3-NbC system. In the t-ZrO2/Al2O3 system, the compositions of 0, 5 and 15% by volume of Al2O3 using commercial powders were studied, while in the t-ZrO2/Al2O3-NbC system, an Al2O3-NbC nanocrystalline powder obtained by high energy reactive milling, deagglomerated, leached in HCl and added in the proportion of 5% by volume to the t-ZrO2 matrix. The obtained powders were uniaxially and isostatically pressed and sintered in conventional furnace and using flash sintering (t-ZrO2/Al2O3) and spark plasma sintering (SPS) (t-ZrO2/Al2O3-NbC). Conventionally sintered t-ZrO2/Al2O3 and conventionally sintered t-ZrO2/Al2O3-NbC composites were characterized by measurements of apparent density, dilatometry, SEM, and mechanical properties: hardness, Young\'s modulus and fracture toughness. The t-ZrO2/Al2O3 composites sintered by FS were characterized by measurements of apparent density, in situ dilatometry and SEM. t-ZrO2/Al2O3-NbC nanocomposites were also characterized for wear strength by the ball-in-disc method, using Al2O3 and WC-6%Co beads as countermaterials. The results showed that the high energy reactive milling was complete and effective in obtaining nanometric powders of Al2O3-NbC, with crystallite sizes equal to 9.1 and 9.7 nm, for Al2O3 and NbC, respectively. The deagglomeration after high energy reactive milling was effective in reducing the size of agglomerates. Conventionally sintered t-ZrO2/Al2O3 and t-ZrO2/Al2O3-NbC composites and SPS-sintered t-ZrO2/Al2O3-NbC showed high densification (> 97% TD), good dispersion of the inclusions in the matrix and good mechanical properties. The t-ZrO2/Al2O3 nanocomposites sintered by FS presented an ultrafast densification (<1 min) with linear shrinkage superior to the sintered samples in conventional furnace, occurring at temperatures lower than 1000°C, with relative densities higher than 90% TD in some compositions. The t-ZrO2/Al2O3-NbC nanocomposites presented competitive properties between conventionally sintered and SPS-sintered composites with higher hardness and fracture toughness than monolithic t-ZrO2. The wear resistance of these conventionally sintered nanocomposites, however, was markedly higher than those of SPS-sintered ones. The oxidation of NbC in the composites sintered conventionally influenced negatively the properties, leading to the suggestion of a \"window\" of temperatures in which the sintering of the t-ZrO2/Al2O3-NbC nanocomposite is interesting without the degradation of the mechanical properties. The results allowed concluding that the studied materials present potential for industrial applications that require high mechanical performance and wear resistance ceramics.

Os compósitos cerâmicos de alto desempenho têm sido objeto de frequentes estudos nas últimas décadas, visando à melhora das propriedades mecânicas e ao aumento da sua gama de aplicações em produtos tecnológicos. Este trabalho consistiu em estudar a preparação, a sinterização convencional e não convencional e as propriedades mecânicas e tribológicas resultantes de dois sistemas compósitos: t-ZrO2/Al2O3 e t-ZrO2/Al2O3-NbC. No sistema t-ZrO2/Al2O3 foram estudadas as composições de 0, 5 e 15% em volume de Al2O3 usando pós comerciais. No sistema t-ZrO2/Al2O3-NbC, foi usado um pó nanocristalino de Al2O3-NbC, obtido por moagem reativa de alta energia e adicionado na proporção de 5% em volume à matriz de t-ZrO2. Os pós foram prensados uniaxial e isostaticamente e sinterizados em forno convencional e pelas técnicas de flash sintering (FS) (t-ZrO2/Al2O3) e spark plasma sintering (SPS) (t-ZrO2/Al2O3-NbC). Os compósitos t-ZrO2/Al2O3 sinterizados convencionalmente e t-ZrO2/Al2O3-NbC sinterizados convencionalmente e por SPS foram caracterizados por medidas de densidade aparente, dilatometria, microscopia eletrônica de varredura (MEV), e medidas de propriedades mecânicas: dureza, módulo de Young e tenacidade à fratura. Os compósitos t-ZrO2/Al2O3 sinterizados por FS foram caracterizados por medidas de densidade aparente, dilatometria in situ e MEV. Os nanocompósitos de t-ZrO2/Al2O3-NbC foram também caracterizados quanto à resistência ao desgaste pelo método esfera-no-disco, utilizando esferas de Al2O3 e WC-6%Co como contramateriais. Os resultados mostraram que a moagem reativa de alta energia foi completa e efetiva na obtenção de pós nanométricos de Al2O3-NbC, com tamanhos de cristalito de 9,1 nm para Al2O3 e 9,7 nm para o NbC. A desaglomeração posterior à moagem de alta energia foi eficaz na redução do tamanho de aglomerados. Os compósitos t-ZrO2/Al2O3 e t-ZrO2/Al2O3-NbC sinterizados convencionalmente e ZrO2/Al2O3-NbC sinterizados por SPS mostraram alta densificação (>97% DT e boas propriedades mecânicas. Os nanocompósitos de t-ZrO2/Al2O3 sinterizados por FS apresentaram uma densificação ultrarrápida (< 1 min) com retração linear superior às amostras sinterizadas em forno convencional, ocorrente a temperaturas inferiores a 1000°C, com densidades relativas superiores a 90% DT em algumas composições. Os nanocompósitos de t-ZrO2/Al2O3-NbC apresentaram propriedades competitivas entre os compósitos sinterizados convencionalmente e por SPS, com dureza e tenacidade à fratura superiores às da t-ZrO2 monolítica. A resistência ao desgaste desses nanocompósitos sinterizados convencionalmente, no entanto, foi notadamente superior à dos sinterizados por SPS. A oxidação do NbC nos compósitos sinterizados convencionalmente influiu negativamente nas propriedades, levando à sugestão de uma \"janela\" de temperaturas em que a sinterização do nanocompósito de t-ZrO2/Al2O3-NbC seja interessante sem a degradação das propriedades mecânicas. Os resultados permitiram concluir que os materiais estudados apresentam potencial para aplicações industriais que requerem cerâmicas de alto desempenho mecânico e de resistência ao desgaste. / High performance ceramic composites have been the subject of frequent studies in recent decades, aiming at improving mechanical properties and increasing their range of applications in technological products. This work consisted in studying the preparation, the conventional and non-conventional sintering and the mechanical properties resulting from two t-ZrO2 matrix composites: the t-ZrO2/Al2O3 system and the t-ZrO2/Al2O3-NbC system. In the t-ZrO2/Al2O3 system, the compositions of 0, 5 and 15% by volume of Al2O3 using commercial powders were studied, while in the t-ZrO2/Al2O3-NbC system, an Al2O3-NbC nanocrystalline powder obtained by high energy reactive milling, deagglomerated, leached in HCl and added in the proportion of 5% by volume to the t-ZrO2 matrix. The obtained powders were uniaxially and isostatically pressed and sintered in conventional furnace and using flash sintering (t-ZrO2/Al2O3) and spark plasma sintering (SPS) (t-ZrO2/Al2O3-NbC). Conventionally sintered t-ZrO2/Al2O3 and conventionally sintered t-ZrO2/Al2O3-NbC composites were characterized by measurements of apparent density, dilatometry, SEM, and mechanical properties: hardness, Young\'s modulus and fracture toughness. The t-ZrO2/Al2O3 composites sintered by FS were characterized by measurements of apparent density, in situ dilatometry and SEM. t-ZrO2/Al2O3-NbC nanocomposites were also characterized for wear strength by the ball-in-disc method, using Al2O3 and WC-6%Co beads as countermaterials. The results showed that the high energy reactive milling was complete and effective in obtaining nanometric powders of Al2O3-NbC, with crystallite sizes equal to 9.1 and 9.7 nm, for Al2O3 and NbC, respectively. The deagglomeration after high energy reactive milling was effective in reducing the size of agglomerates. Conventionally sintered t-ZrO2/Al2O3 and t-ZrO2/Al2O3-NbC composites and SPS-sintered t-ZrO2/Al2O3-NbC showed high densification (> 97% TD), good dispersion of the inclusions in the matrix and good mechanical properties. The t-ZrO2/Al2O3 nanocomposites sintered by FS presented an ultrafast densification (<1 min) with linear shrinkage superior to the sintered samples in conventional furnace, occurring at temperatures lower than 1000°C, with relative densities higher than 90% TD in some compositions. The t-ZrO2/Al2O3-NbC nanocomposites presented competitive properties between conventionally sintered and SPS-sintered composites with higher hardness and fracture toughness than monolithic t-ZrO2. The wear resistance of these conventionally sintered nanocomposites, however, was markedly higher than those of SPS-sintered ones. The oxidation of NbC in the composites sintered conventionally influenced negatively the properties, leading to the suggestion of a \"window\" of temperatures in which the sintering of the t-ZrO2/Al2O3-NbC nanocomposite is interesting without the degradation of the mechanical properties. The results allowed concluding that the studied materials present potential for industrial applications that require high mechanical performance and wear resistance ceramics.

published_or_final_version / Mechanical Engineering / Doctoral / Doctor of Philosophy

published_or_final_version / abstract / toc / Mechanical Engineering / Master / Master of Philosophy

The microwave induced plasma was used to sinter synthetic Idaho Chemical Processing Plant (ICPP) alumina and zirconia based high level nuclear waste calcines in a nitrogen atmosphere. The sintering behavior of these nuclear waste calcines was observed with identification of the phases formed. A sintered density of higher than 3.20 g/cm3 was obtained within 10 minutes of plasma sintering of pure calcines. The addition of frit in pure calcines to form glass-ceramics resulted in a decrease of density to less than 2.0 g/cm3. This was attributed to the reaction between frit and volatile substances in both zirconia based and alumina based calcines. The removal of volatile substances before sintering increased the sintered density of calcines. The lower sintered density was obtained for the more volatile samples. The phases formed in the plasma sintering of calcines were identified as a function of temperature and amount of frit.

No description available.

No description available.

No description available.

The aim of this study was to investigate a zirconia-matrix reinforced with metal powder (chromium, iron and stainless steel (AISI 316)) including processing, characterisation, and measurements of their properties (mechanical, thermal and electrical). Zirconia stabilised with 5.4 wt% Y₂0₃ (3 mol%) as the matrix was first studied and followed by an investigation of the effects of metal reinforcement on zirconia-matrix composites. Monolithic zirconia was pressureless sintered in air and argon to observe the effect of sintering atmosphere, while the composites were pressureless sintered in argon to avoid oxidation. Sintering was carried out at various temperatures for 1 hour and 1450°C was chosen to get almost fully dense samples. The density of the fired samples was measured using a mercury balance method and the densification behaviour was analysed using TMA (Thermo-mechanical Analysis). The TMA was also used to measure the coefficient of thermal expansion. In addition, thermal analysis using DTA and TGA was performed to observe reactions and phase transformations. Moreover, optical microscopy and SEM were used to observe the microstructures, XRD was used for phase identification, and mechanical properties including Vickers hardness, fracture toughness and bending strength were measured. The effect of thermal expansion mismatch on thermal stresses was also analysed and discussed. Finally, thermal diffusivity at room temperature and as a function of temperature was measured using a laser flash method, and to complete the study, electrical conductivity at room temperature was also measured. The investigation of monolithic zirconia showed that there was no significant effect of air and argon atmosphere during sintering on density, densification behaviour, microstructures, and properties (mechanical and thermal). Furthermore, the results were in good agreement with that reported by previous researchers. However, the presence of metal in the composites influenced the sintering behaviour and the densification process depends on the metal stability, reactivity, impurity, particle size, and volume fraction. Iron reacted with yttria (zirconia stabiliser), melted and reduced the densification temperature of monolithic zirconia, while chromium and AISI 316 did not significantly affect the densification temperature and did not react with either zirconia or yttria. AISI 316 melted during fabrication. Moreover, all of the metal reinforcements reduced the final shrinkage of monolithic zirconia. In terms of properties, the composites showed an increase in fracture toughness, and a reduction in Vickers hardness and strength with increasing reinforcement content. In addition, the thermal diffusivity of the composites showed an increase with reinforcement content for the zirconia/chromium and zirconia/iron composites, but not for the zirconia/AISI 316 composites due to intrinsic mircocracking. Furthermore, all the composites became electrically conductive with 20 vol% or more of reinforcement. It has been concluded that of those composites the zirconia/chromium system may be considered as having the best combination of properties and although further development is needed for such composites to be used in real applications in structural engineering, the materials may be developed based on these findings. In addition, these findings may be used in development of ceramic/metal joining as composite interlayers are frequently used.