La nature est complexe et c’est en toute modestie que les ingénieurs doivent chercher à prédire le comportement des ouvrages dans le sous-sol. La réalisation de projets industriels dans le domaine souterrain, à forts enjeux économiques et sociaux (traversées alpines, stockage de déchets nucléaires), nécessite d’évoluer vers une meilleure compréhension des mécanismes comportementaux des ouvrages à concevoir. Cette amélioration passe par une meilleure représentativité physique des mécanismes macroscopiques et par la mise à disposition d’outils de prédiction adaptés aux attentes et aux besoins des ingénieurs. Les outils de calculs développés dans ce travail s’inscrivent dans cette volonté de rapprocher les attentes de l’industrie et les connaissances liées à la rhéologie des géomatériaux. Ces développements ont ainsi débouché sur la proposition d’un modèle de comportement mécanique, adapté aux roches peu fissurées et assimilables à des milieux continus, intégrant, en particulier, l’effet du temps. Fil conducteur de cette étude, la problématique du sujet de thèse concerne précisément la prise en compte du comportement différé des massifs rocheux dans les modélisations et ses conséquences sur les ouvrages souterrains.Fondé sur des concepts physiques de référence, définis à différentes échelles (macro/méso/micro), le modèle rhéologique développé est transcrit dans un formalisme mathématique dans le but d’être mis en oeuvre numériquement.Les applications numériques proposées s’inscrivent principalement dans le contexte du stockage des déchets radioactifs. Elles concernent deux configurations d’ouvrages rigoureusement différentes : l’excavation du laboratoire souterrain canadien de l’AECL, dans le granite du Lac du Bonnet et le creusement de la galerie GMR du laboratoire de Bure (Meuse/Haute-Marne) dans l’argilite de l’Est. Dans les deux cas, l’utilisation du modèle a permis de mettre en évidence l’apport de la prise en compte du comportement différé sur la représentativité des prédictions numériques du comportement à court, moyen et long termes des ouvrages souterrains / Nature is complex and must be approached in total modesty by engineers seeking to predict the behavior of underground openings. The engineering of industrial projects in underground situations, with high economic and social stakes (Alpine mountain crossings, nuclear waste repository), mean striving to gain better understanding of the behavioral mechanisms of the openings to be designed. This improvement necessarily involves better physical representativeness of macroscopic mechanisms and the provision of prediction tools suited to the expectations and needs of the engineers. The calculation tools developed in this work is in step with this concern for satisfying industrial needs and developing knowledges related to the rheology of geomaterials. These developments led to the proposing of a mechanical constitutive model, suited to lightly fissured rocks, comparable to continuous media, while integrating more particularly the effect of time.Thread of this study, the problematics ensued from the subject of the thesis is precisely about the rock mass delayed behavior in numerical modeling and its consequences on underground openings design.Based on physical concepts of reference, defined in several scales (macro/meso/micro), the developed constitutive model is translated in a mathematical formalism in order to be numerically implemented.Numerical applications presented as illustrations fall mainly within the framework of nuclear waste repository problems. They concern two very different configurations of underground openings: the AECL’s underground canadian laboratory, excavated in the Lac du Bonnet granite, and the GMR gallery of Bure’s laboratory (Meuse/Haute-Marne), dug in argillaceous rock.In this two cases, this constitutive model use highlights the gains to be obtained from allowing for delayed behavior regarding the accuracy of numerical tunnel behavior predictions in the short, medium and long terms

The master's thesis focuses on preparation of blown films from polylactid acid (PLA) which was blended with selected polyesteres – poly(butylene adipate-co-terephtalate) (PBAT), polycaprolactone (PCL) and polybutylene succinate (PBS) – and thermoplastic starch (TPS) in amount of 30% in order to soften PLA films. The influence of the aditives on static and mechanical tensile properties, on structure, morphology and thermal properties of the films was determined and the obtained parameters were compared to properties of films prepared from neat PLA and high density polyethylene (HDPE). The results showed that the additives increased crystalinity of PLA and thus significantly influenced the properties of the films. In contrast to the film from neat PLA, softening in terms of lowering glass transition temperature occured only by adding PBS and TPS, in terms of increasing ductility only by adding PBAT. All PLA films showed nearly constant elastic modulus up to the beginning of glass transition enabling their potential application till 50 °C. Preparation of the film with TPS was problematic and the film showed the worst mechanical properties. Preparation of other films was without any problems. The most promising additive from the tested ones was PBAT which showed comparable mechanical properties as the film from HDPE.

In the introduction of the Master’s thesis describes for obtaining and processing of reclaimed asphlalt. Major point of the thesis is design of asphalt mixtures with use of higher amount of RAP for asphalt binder course. Asphalt mixtures were designed with contents of 0%, 30%, 50% and 70% of RAP. On each asphalt mixtures were compared parameters set out by functional tests – resistence to permanent deformation and resistence to water.

The comparison of rheological properties (complex shear modulus and phase angle and dynamic viscosity) of four paving bitumens and two polymer modified bitumens is performed in this diploma thesis. Furthermore, the empirical tests (needle penetration and softening point) were determined on these binders. Effect of asphalt binders aging was modeled using RTFOT test and modified RTFOT test (3 x RTFOT).

Diploma thesis is particularly focused on ageing of asphalt mixtures and asphalt binders. In the theoretical part an array of methods simulating short term and long term ageing consequently is introduced. The main objective of the practical part was to carry out the long-term ageing test method BSA (Braunschweiger Alterung). Thereafter, specimens testing for stiffness properties according to CSN EN 12697-26 were made. After conducting the measurement on those, asphalt binder was extracted and processed to follow-up testing. The testing consisted of a range of methods – Penetration CSN EN 1426, Ring and Ball test CSN EN 1427, Determination of the Frass breaking point CSN EN 12593, Determination of complex shear modulus CSN EN 14770 and Dynamic viscosity using a dynamic shear rheometer (DSR). The given results were assessed in the last part in order to evaluate the rate of the binder degradation caused by the method BSA.

The thesis describes the relaxation properties of bituminous binders determined in dynamic shear rheometer (DSR). Paving bitumen, polymer modified bitumen (PMB) and crumb rubber modified bitumen (CRmB) were chosen for comparison. In order to describe the effects of ageing on asphalt binders relaxation properties, the laboratory simulation of ageing using RTFOT and 3xRTFOT method was performed. For each binder were simultaneously conducted tests of needle penetration, softening point and elastic recovery. Selected bitumens were used for the production of asphalt mixtures. The low-temperature properties tests (TSRST) were performed for these mixtures, when the results were compared to the relaxation properties of binders determined in the DSR.

Multiple step tests under cyclic strain control have been performed using cylindrical specimens of cast polycrystalline Inconel 738LC superalloy at 23, 700, 500, 800 and 900 °C in laboratory atmosphere to obtain cyclic stress-strain curves. During cyclic straining of specimen were obtained cyclic hardening-softening curves. Their progress changed with temperature and strain amplitude. Evaluated cyclic stress-strain curves are shifted to lower stresses with increasing temperature. Surface relief was observed in fatigued specimens under SEM and metalography under optic microscopy. Slip markings were studied on specimen surface fatigued at 700 °C .Stress-strain response is compared and discussed in relation to the surface observations - persistent slip markings.

The theoretical part of this thesis describes the rheology of bituminous binders, aging of asphalt binders and laboratory methods simulating short and long term aging. The following describes an empirical tests (needle penetration, softening point ring ball method) and functional tests (complex shear modulus and phase angle, dynamic viscosity), which are performed in the dynamic shear rheometer. At the end of this section, laboratory aging of bituminous binders using method RTFOT and method RTFOT + PAV is described in more detail. In the practical part of this thesis, the results of all tests performed on the binders aged using RTFOT + PAV are introduced and compared with results of properties of non-aged binders and binders aged by 3xRTFOT.

Ces travaux de thèse portent sur l'étude expérimentale des propriétés physiques et de la biomécanique des agrégats cellulaires embryonnaires. Le but de cette thèse était d'une part de mieux comprendre l'origine biologique de la viscosité et de la tension de surface tissulaire, d'autre part d'étudier quantitativement en détail l'élasticité cellulaire par des nouvelles mesures de rhéologie en cisaillement. Un premier chapitre concerne les mesures de tension de surface tissulaire par la méthode de compression et de viscosité tissulaire par analyse de la cinétique de fusion de deux agrégats en faisant varier comme paramètre principal la contractilité cellulaire que certains suspectent comme étant la principale origine biologique de ces paramètres. Nous utilisons le formalisme du DITH (Haris, 1976: Differential Interfacial Tension Hypothesis) pour interpréter les données. Le deuxième chapitre concerne les mesures rhéologiques en cisaillement à l'aide d'un rhéomètre commercial plan-plan sur plusieurs centaines ou milliers d'agrégats cisaillés ensembles. Nous montrons que les cellules deviennent moins rigides pour une déformation minimale d'environ 4%, mais sur l'échelle de l'heure les cellules sont capables de se rigidifier à nouveau. Ces expériences sont analysées à l'aide d'un modèle de ressorts qui cassent sous contrainte puis se ressoudent à contrainte nulle / This thesis focuses on the experimental study of physical properties and biomechanics of embryonic cell aggregates. The aim of this thesis was on one hand to better understand the biological origin of tissue viscosity and tissue surface tension, and on the other hand to study quantitatively in detail cell elasticity by means of new rheological measurements in shear. A first chapter deals with measurements of tissue surface tension by tissue compression method and tissue viscosity by analysis of the fusion kinetics of two aggregates. We vary key parameters such as cell contractility that some people suspect to be the main biological origin of these parameters. We use the formalism of DITH (Haris, 1976: Differential Interfacial Tension Hypothesis) to interpret the data. The second chapter deals with rheological measurements in shear using a commercial plate-plate rheometer over several hundred of aggregates. We showed that cells become softer after a minimal deformation of 4% is reached, and can harden again on the timescale of hour. These experiences are analyzed using a model of springs that break under stress and then reattach at zero strain

This thesis deals with the modification of asphalt binder 50/70 with fast reacting SBS. This is a relatively new additive that should be able to improve the binder properties during mixing of the asphalt mix at the plant. In the theoretical part, the issue of asphalt-mixing plant and polymer modification additives is presented. Furthermore, the test methods used such as needle penetration, softening point, determination of the elastic recovery, DSR and MSCR are described. Several modified binder samples were developed for the tests, in which mixing temperature, mixing time and SBS content were combined. The results of each test were compared and evaluated at the end of the thesis.