Uma simulação numérica do ciclo de refrigeração a adsorção é realizada para os pares zeólita-água e carvão ativo AC-35 metanol, justificando a escolha do par bem como do sistema de captação a serem utilizados no protótipo. O protótipo construído compreende um concentrador cilíndrico-parabólico com rastreamento solar, um tubo de calor e uma unidade frigorífica (com zeólita-água). Aspectos tecnológicos como válvulas, soldas e carregamento do par na máquina são analisados. Os resultados dos testes de desempenho são apresentados, discutidos e comparados com a literatura. Uma análise de custos é feita. Paralelamente, construímos termo pilhas pelo método da evaporação. Estas termopilhas foram utilizadas na construção do piranômetro e do pireliômetro. Os instrumentos são caracterizados em termos de sensibilidade, constante de tempo, linearidade, efeitos de temperatura e convecção natural. Os resultados desta caracterização são discutidos e comparados com um modelo fabricado pela Eppley. Finalmente, no apêndice I, testamos o desempenho de um coletor plano utilizando no absorvedor o revestimento seletivo de óxido de alumínio recentemente desenvolvido no IFQSC. As melhores condições para obtenção do revestimento seletivo em placas de grande porte são estudadas. / A numerical simulation of the adsorption refrigeration cycle was made for zeolite/water and activated carbon(AC-35)/ methanol pairs, to select the pair and the solar collector in the prototype. The fabricated prototype consists of a cylindrical paraolic concentrator with solar trackins, a heat pipe and the refrigeration unit (with the zeolite/water pair). The technical aspects of values, welds and out-gassing are analyzed. The results of the performance tests are presented, discussed and compared with the literature. An analysis of costs is made. In parallel thermopiles were constructed using the evaporation method. These thermopiles were used in the construction of the piranometer and the pirheliometer. The instruments were characterized in terms of: sensitivity, stability with time, linearity, effects of temperature and natural convenction. The results of this characterization are discussed and compared with a model made by Eppley. Finally, in Apendix I, we tested the performance of a flat plate collector using a selective coating of aluminium oxide (developed in IFQSC) as absorber. The Best conditions for obtaining the seletive coating on big size plates are discussed.

Uma simulação numérica do ciclo de refrigeração a adsorção é realizada para os pares zeólita-água e carvão ativo AC-35 metanol, justificando a escolha do par bem como do sistema de captação a serem utilizados no protótipo. O protótipo construído compreende um concentrador cilíndrico-parabólico com rastreamento solar, um tubo de calor e uma unidade frigorífica (com zeólita-água). Aspectos tecnológicos como válvulas, soldas e carregamento do par na máquina são analisados. Os resultados dos testes de desempenho são apresentados, discutidos e comparados com a literatura. Uma análise de custos é feita. Paralelamente, construímos termo pilhas pelo método da evaporação. Estas termopilhas foram utilizadas na construção do piranômetro e do pireliômetro. Os instrumentos são caracterizados em termos de sensibilidade, constante de tempo, linearidade, efeitos de temperatura e convecção natural. Os resultados desta caracterização são discutidos e comparados com um modelo fabricado pela Eppley. Finalmente, no apêndice I, testamos o desempenho de um coletor plano utilizando no absorvedor o revestimento seletivo de óxido de alumínio recentemente desenvolvido no IFQSC. As melhores condições para obtenção do revestimento seletivo em placas de grande porte são estudadas. / A numerical simulation of the adsorption refrigeration cycle was made for zeolite/water and activated carbon(AC-35)/ methanol pairs, to select the pair and the solar collector in the prototype. The fabricated prototype consists of a cylindrical paraolic concentrator with solar trackins, a heat pipe and the refrigeration unit (with the zeolite/water pair). The technical aspects of values, welds and out-gassing are analyzed. The results of the performance tests are presented, discussed and compared with the literature. An analysis of costs is made. In parallel thermopiles were constructed using the evaporation method. These thermopiles were used in the construction of the piranometer and the pirheliometer. The instruments were characterized in terms of: sensitivity, stability with time, linearity, effects of temperature and natural convenction. The results of this characterization are discussed and compared with a model made by Eppley. Finally, in Apendix I, we tested the performance of a flat plate collector using a selective coating of aluminium oxide (developed in IFQSC) as absorber. The Best conditions for obtaining the seletive coating on big size plates are discussed.

CoordenaÃÃo de AperfeiÃoamento de Pessoal de NÃvel Superior / Apresenta a validaÃÃo experimental de um novo refrigerador solar por adsorÃÃo com aquecimento indireto. Os componentes do refrigerador sÃo: adsorvedor, condensador, evaporador e coletor solar. A escolha do par adsorbato / adsorvente, Ãgua e sÃlica gel tipo RD, respectivamente, levou em consideraÃÃo as temperaturas alcanÃadas pelos coletores e disponÃveis para a dessorÃÃo do fluÃdo refrigerante (Ãgua) das cavidades do material adsorvente (sÃlido poroso). Devido à coexistÃncia das etapas de aquecimento e resfriamento no adsorvedor, foi definida uma geometria para este componente capaz de permitir uma melhor dissipaÃÃo de calor no material adsorvente na fase de resfriamento, e a conservaÃÃo de energia tÃrmica durante a fase de aquecimento. Os resultados experimentais comprovaram o funcionamento do refrigerador, visto que foram atingidas temperaturas de 140ÂC na entrada do adsorvedor, 80ÂC no leito adsortivo e de 4,4ÂC no evaporador, possibilitando sua aplicaÃÃo em sistemas de condicionamento de ar / This work presents the experimental validation of a new adsorption solar refrigeration with indirect heating. The components of the refrigerator are: an adsorber, a condenser, an evaporator, and a solar collector. The choice of the adsorbate / adsorbent pair, water and silica gel type RD, respectively, took into consideration the temperatures reached by the solar collectors and available for the desorption of the refrigerant fluid (water) from the cavities of the adsorbent material (a porous solid). Due to the co-existence of the heating and cooling phases in the adsorber, a specific geometry for this component was defined so as to allow a good heat dissipation in the adsorbent material in the cooling phase, and the conservation of thermal energy in the heating phase. The experimental results validate the operation of the refrigerator, as temperature valves of 140ÂC at the inlet of the adsorber, of 80ÂC in the adsorber bed, and of 4,4ÂC in the evaporator were reached, allowing its application in air conditioning systems

In this report the design and testing of a plug and play system to run Coolfinity’s Icevolt 300 refrigerator on solar panels is discussed. Such a system will be able to provide adequate cooling for food & beverages in area’s with unreliable or no electricity available. Currently such systems are only available for small chest refrigerators, while the Icevolt 300 is a large standing commercial refrigerator with a glass door. This is ideal for shops, cafés restaurants and smaller distribution centres. The system contains a solar charge controller, a battery and an inverter. First the component specifications and required solar panels are calculated. From those calculations system components are evaluated. A custom casing is designed to fit the components. An OEM is chosen and the chosen Inverter is tested extensively. The tests show that the inverter does not have any problems starting the Icevolt 300 compressor at a reduced voltage. Many battery manufacturers are evaluated and samples from three different manufacturers are obtained and tested. Samples of one of the manufacturers match specifications and have no issues with the high start up power of the compressor. A full system test proofs that the system works, but also indicates that the original refrigerator consumption estimate was too low. This means more PV panels are needed than originally estimated. With the information from the tests a new model is build that estimates the performance more accurate. A program is written to estimate the performance and decide the PV panels required. The pilot series of the case showed a lot of improvements are needed in the case design, especially on cost. A test is prepared in Mali but no test data is obtained yet. Based on the work done it would be recommend to investigate DC direct refrigerators instead of continuing the path of PV to AC systems. / I denna rapport diskuteras design och testning av ett plug and play - system för att köra Coolfinity’s Icevolt 300 -kylskåp på solpaneler. Ett sådant system kommer att kunna tillhandahålla tillräcklig kylning för mat och dryck i områden med opålitlig eller ingen tillgänglig el. För närvarande är sådana system endast tillgängliga för små kylboxar, medan Icevolt 300 är ett stort stående kommersiellt kylskåp med en glasdörr. Detta är idealiskt för butiker, kaféer och mindre distributionscentra. Systemet innehåller en laddningsregulator för solpaneler, ett batteri och en växelriktare. Först beräknas komponentspecifikationerna och nödvändiga solpaneler. Utifrån dessa beräkningar utvärderas systemkomponenter. Ett anpassat hölje är utformat för att passa komponenterna. En OEM väljs och den valda växelriktaren testas utförligt. Testerna visar att växelriktaren inte har några problem att starta Icevolt 300 -kompressorn med reducerad spänning. Många batteritillverkare utvärderas och prover från tre olika tillverkare erhålls och testas. Prover från en av tillverkarna matchar specifikationerna och har inga problem med kompressorns höga starteffekt. Ett fullständigt systemtest bevisar att systemet fungerar, men indikerar också att den ursprungliga uppskattningen av kylförbrukningen var för låg. Det betyder att fler PV -paneler behövs än vad som ursprungligen beräknades. Med informationen från testerna byggs en ny modell som uppskattar prestandan mer exakt. Ett program skrivs för att uppskatta prestanda och bestämma vilka PV -paneler som krävs. Pilotserien för höljet visade att många förbättringar behöver göras vad beträffar höljets design, särskilt vad gäller kostnaden. Ett test förbereds i Mali men inga testdata har erhållits ännu. Baserat på det utförda arbetet skulle det rekommenderas att undersöka direkta DC -kylskåp istället för att fortsätta vägen för PV till AC-system.

La réfrigération solaire est une alternative à la production de froid à partir de machines à compression mécanique de vapeur dont l’alimentation est électrique. Parmi les technologies envisageables, le couplage d’une machine de réfrigération thermoacoustique avec un concentrateur solaire et un stockage frigorifique par chaleur latente apparait comme une option intéressante. Cette thèse introduit la problématique du sujet et présente les différentes technologies envisageables pour la conception d’un réfrigérateur thermoacoustique solaire. Ensuite, pour répondre au problème, le prototype expérimental qui a été conçu et fabriqué est présenté. Une méthode de modélisation transitoire au niveau système du prototype est proposée. Enfin les résultats obtenus par les simulations dynamiques sont discutés à travers l’analyse du comportement transitoire de l’ensemble du procédé et des performances associées. / Solar refrigeration is an alternative to electrically driven vapor compression cycle for refrigeration. Among the solar refrigeration technologies, the coupling of a heat driven thermoacoustic refrigerator with a solar concentrator and a cold latent energy storage system seems to be a promising technology. This thesis introduces the issue of the subject and analyzes the different available technologies to design a solar driven thermoacoustic refrigerator. Then, to address the problem, the prototype that has been designed and built, is presented. A lumped model is introduced to describe the transient behavior of the prototype. Finally, simulation results are presented and discussed in terms of dynamic behavior and performance analysis.