There has been a huge rise in interest in the design of energy efficient wireless sensor networks (WSN) and body area networks (BAN) with the advent of many new applications over the last few decades. The number of sensor nodes in these applications has also increased tremendously in the order of few hundreds in recent years. A typical sensor node in a WSN consists of circuits like RF transceivers, micro-controllers or DSP, ADCs, sensors, and power supply circuits. The RF transmitter and receiver circuits mainly the frequency synthesizers(synthesis of RF carrier and local oscillator signals in transceivers) consume a significant percentage of its total power due to its high frequency of operation. A charge-pump phase locked loop (CP-PLL) is the most commonly used frequency synthesizer architecture in these applications. The growing demands of WSN applications, such as low power consumption larger number of sensor nodes, single chip solution, and longer duration operation presents several design challenges for these transmitter and frequency synthesizer circuits in these applications and a few are listed below, Low power frequency synthesizer and transmitter designs with better spectral performance is essential for an energy efficient operation of these applications. The spurious tones in the frequency synthesizer output will mix the interference signals from nearby sensor nodes and from other interference sources present nearby ,to degrade the wireless transmitter and receiver performance[1]. With the increased density of sensor nodes (more number of in-band interference sources) and degraded performance of analog circuits in the nano-meter CMOS process technologies, the spur reduction techniques are essential to improve the performance of frequency synthesizers in these applications. A single chip solution of sensor nodes with its analog and digital circuits integrated on the same die is preferred for its low power, low cost, and reduced size implementation. However, the parasitic interactions between these analog and digital sub-systems integrated on a common substrate, degrade the spectral performance of frequency synthesizers in these implementations[2]. Therefore, techniques to improve the mixed signal integration performance of these circuits are in great demand. In this thesis, we present a custom designed energy efficient 2.4 GHz BFSK/ASK transmitter architecture using a low power frequency synthesizer design technique taking advantage of the CMOS technology scaling benefits. Furthermore, a few design guidelinesandsolutionstoimprovethespectralperformanceoffrequency synthesizer circuits and in-turn the performance of transmitters are also presented. The target application being short distance, low power, and battery operated wireless communication applications. The contributions in this thesis are, Spectral performance improvement techniques The CP mismatch current is a dominant source of reference spurs in the nano-meter CMOS PLL implementations due to its worsened channel length modulation effect [3]. In this work, we present a CP mismatch current calibration technique using an adaptive body bias tuning of its PMOS transistors. Chip prototype of 2.4 GHzCP-PLLwith the proposed CP calibration technique was fabricated in UMC 0.13 µm CMOS process. Measurements show a CP mismatch current of less than 0.3 µA(0.55 %) using the proposed calibration technique over the VCO control voltage range 0.3 to 1 V. The closed loop PLL measurements using the proposed technique exhibited a 9dB reduction in the reference spur levels across the PLL output frequency range 2.4 -2.5 GHz. The parasitic interactions between analog and digital circuits through the common substrate severely affects the performance of CP-PLLs. In this work, we experimentally demonstrate the effect of periodic switching noise generated from the digital buffers on the performance of charge-pump PLLs. The sensitivity of PLL performance metrics such as output spur level, phase noise, and output jitter are monitored against the variations in the properties of a noise injector digital signal. Measurements from a 500 MHz CP-PLL shows that the pulsed noise injection with the duty cycle of noise injector signal reduced from 50% to 20%, resulted in a 12.53 dB reduction in its output spur level and a 107 ps reduction in its Pk-Pk deterministic period jitter performance. Low power circuit techniques A low power frequency synthesizer design using a digital frequency multiplication technique is presented. The proposed frequency multiply by 3 digital edge combiner design having a very few logic gates, demonstrated a significant reduction in the power consumption of frequency synthesizer circuits, with an acceptable spectral performance suitable for these relaxed performance applications. A few design guidelines and techniques to further improve its spectral performance are also discussed and validated through simulations. Chip prototypes of 2.4 GHz CP-PLLs with and without digital frequency multiplier circuits are fabricated in UMC 0.13 µm CMOS process. The 2.4 GHz CP-PLL using the proposed digital frequency multiplication technique (10.7 mW) consumed a much reduced power compared to a conventional implementation(20.3 mW). A custom designed, energy efficient 2.4 GHz BFSK/ASK transmitter architecture using the proposed low power frequency synthesizer design technique is presented. The transmitter uses a class-D power amplifier to drive the 50Ω antenna load. Spur reduction techniques in frequency synthesizers are also used to improve the spectral performance of the transmitter. A chip prototype of the proposed transmitter architecture was implemented in UMC0.13 µm CMOS process. The transmitter consume14 mA current from a 1.3V supply voltage and achieve improved energy efficiencies of 0.91 nJ/bit and 6.1 nJ/bit for ASK and BFSK modulations with data rates 20Mb/s & 3Mb/s respectively.

THE THESIS FOCUSES ON A CONSTRUCTION DESIGN OF A NEW DRILLING HEAD DESIGNED TO REPLACE THE ORIGINAL ONE IN A MULTIDRILL HYNDAGA DRILLING RING. THE SUBSTITUTION IS SUPPOSED TO PROVIDE A SOLUTION TO THE SHORTCOMINGS OF THE CURRENTLY USED DRILLING HEAD. THE THESIS ANALYSES PARAMETERS OBTAINED FROM THE MANUFACTURER, NEW PRODUCTION REQUIREMENTS AND PROPOSES TWO TYPES OF MOTORS INNOVATIVE METHODS HAD BEEN IMPLEMENTED IN CALCULATIONS OF CONCEPTUAL PARAMETERS OF THE NECESSARY COMPONENTS. THE OUTCOME IS A NEW F-TYPE DRILLING HEAD.

The thesis deal with design of coaxial high-speed gear box for small-scale turboshaft engines. At the beginning a study of problems was performed and for design concept was elected version of single-shaft turbo-engine with electric generator. Kinematic diagram, type of gear design, material and lubrication method was designed. Further was solved proposal of basic gearing parameters, choice of the number of tooth and basic proposal calculations were performed. Was performed check calculation of gearing, calculation of bearings durability and was processed design documentation in required range. Designed gear reducer has two stage with three coutershafts, that are deployed evenly about main axis of reducer. First stage is gear with external gearing, second stage with internal gearing. The thesis may be used as a template for next similar gear reducers design.

Η πληθώρα των εφαρμογών που μπορεί να εξυπηρετήσει η τεχνολογία Υπερευρείας Ζώνης (UWB), από τα ασύρματα προσωπικά δίκτυα υψηλών ταχυτήτων, μέχρι τα ασύρματα δίκτυα αισθητήρων με δυνατότητες ακριβούς εντοπισμού θέσης, και τα ασύρματα δίκτυα ιατρικών αισθητήρων, έχει προκαλέσει έντονο ερευνητικό ενδιαφέρον γύρω από τις υλοποιήσεις UWB συστημάτων. Η ασυνήθιστα μεγάλη περιοχή συχνοτήτων που έχει ανατεθεί στο UWB, από τα 3.1-10.6 GHz, επιτρέπει την επίτευξη υψηλών ταχυτήτων με απλά σχήματα διαμόρφωσης, ωστόσο, λόγω της διαμοίρασης του φάσματος με τις υφιστάμενες τεχνολογίες ασύρματης δικτύωσης, οι UWB εκπομπές πρέπει να περιορίζονται σε ισχύ κάτω από το κατώφλι των -41.3 dBm/MHz, ικανοποιώντας πολύ αυστηρές μάσκες εκπομπής που εισάγουν έντονες προκλήσεις στη σχεδίαση των πομπών. Η υλοποίηση αναδιατάξιμων UWB πομπών σε σύγχρονες CMOS τεχνολογίες, με υψηλή φασματική ευελιξία, ταχύτητα και ποιότητα διαμόρφωσης, καθώς και με χαμηλή κατανάλωση, αποτέλεσε το αντικείμενο της συγκεκριμένης διατριβής. Υιοθετώντας την αρχιτεκτονική Multi-Band Impulse-Radio (MB-IR) σε συνδυασμό με την τεχνική Direct Sequence BPSK, η έρευνα προσανατολίστηκε προς την ανάπτυξη καινοτόμων μονάδων βασικής ζώνης, με στόχο την ενεργειακά αποδοτική αντιστροφή Γκαουσιανών μορφοποιημένων παλμών υψηλής ποιότητας φάσματος και διάρκειας μικρότερης ακόμα και από 1 nsec. Προς αυτή την κατεύθυνση, αναπτύχθηκε μια καινοτόμα γεννήτρια Γκαουσιανών παλμών με πολύ χαμηλούς πλευρικούς λοβούς στο φάσμα, τυπικά κάτω από -40 dB, ώστε να υποστηρίζονται οι αυστηρότερες μάσκες εκπομπής ή και μελλοντικές. Η σχεδίασης της προτεινόμενης γεννήτριας είχε ως κριτήριο την ευέλικτη ρύθμιση της διάρκειας των παραγόμενων παλμών, και αξιοποίησε τη χαρακτηριστική μεταφοράς τάσης ενός ωμικά φορτωμένου, ασύμμετρου CMOS αντιστροφέα. Η γεννήτρια βασίζεται κυρίως σε ψηφιακά κυκλώματα πολύ χαμηλής τάσης και, σε σύγκριση με τις υφιστάμενες υλοποιήσεις, παρουσιάζει σημαντικό προβάδισμα στον τομέα της ταχύτητας, καθώς και στο πλάτος εξόδου, η μεγάλη τιμή του οποίου χαλαρώνει σημαντικά τη σχεδίαση του RF front end. Η γεννήτρια μελετήθηκε διεξοδικά, διεξήχθη ανάλυση κλιμάκωσης, έγινε εξαγωγή σχεδιαστικών εξισώσεων και αναπτύχθηκαν εργαλεία λογισμικού για την αυτοματοποιημένη σχεδίασή της. Για περαιτέρω αύξηση της ταχύτητας των παλμικών σημάτων εφαρμόσθηκε ειδική σχεδίαση, η οποία αντιπραγματεύεται την ταχύτητα με το επίπεδο των λοβών του φάσματος. Για την αποδοτική BSPK διαμόρφωση των Γκαουσιανών παλμών αναπτύχθηκε ειδική τοπολογία “Μεταγωγής Σήματος Πυροδότησης Πλήρους Ισορροπίας με Up-Conversion”. Η τοπολογία αυτή, σε αντίθεση με τις ανταγωνιστικές τοπολογίες, αποφεύγει την αντιστροφή του παλμού με αναλογικά κυκλώματα υψηλής κατανάλωσης, αλλά και την αναλογική μεταγωγή, καθώς η διαμόρφωση λαμβάνει χώρα πριν από την παραγωγή των παλμών. Παράλληλα, επιτυγχάνονται υψηλοί ρυθμοί, καθώς και υψηλή ποιότητα διαμόρφωσης λόγω των ισορροπημένων μονοπατιών της τοπολογίας. Η γεννήτρια μαζί με το διαμορφωτή αποτελούν τις καινοτόμες παρεμβάσεις στη μονάδα Βασικής Ζώνης του προτεινόμενου πομπού. Για την ολοκλήρωση της λειτουργικότητας του πομπού, αναπτύχθηκε ένα RF front end, το οποίο αποτελείται από έναν διπλά ισορροπημένο μίκτη, έναν LO buffer, ένα μετατροπέα διαφορικού σήματος σε απλό, και έναν ενισχυτή ισχύος, ο οποίος είναι προσαρμοσμένος στα 50 Ohms, χωρίς να απαιτεί κανένα εξωτερικό στοιχείο. Το RF front end ολοκληρώθηκε μαζί με τη μονάδα βασικής ζώνης, και ο ολοκληρωμένος πομπός κατασκευάστηκε σε τεχνολογία CMOS 130 nm. Το ολοκληρωμένο προσαρτήθηκε στην RF πλακέτα συστήματος με την τεχνική Chip on Board. Για την επιτυχία του συστήματος με την πρώτη προσπάθεια έγινε συσχεδίαση σε επίπεδο IC-Package-PCB, δίνοντας ιδιαίτερη έμφαση στα ζητήματα Signal/Power Integrity. Ο πομπός παρουσίασε την υψηλότερη ταχύτητα από τις ανταγωνιστικές MB-IR UWB υλοποιήσεις, ίση με 1.5 Gbps, με αντίστοιχη ενεργειακή αποδοτικότητα 21 pJoule/bit και μέτρο διανυσματικού σφάλματος 5.5%. Ο πομπός βελτίωσε τους πλευρικούς λοβούς στο φάσμα περισσότερο από 10 dB, ενώ η διατριβή, εκμεταλλευόμενη την αναδιαταξιμότητα του πομπού, παρουσιάζει, επιπλέον, τις πρώτες μετρήσεις σε ταχύτητες εκατοντάδων Mbps για ικανοποίηση της χαμηλής ζώνης της πρόσφατα θεσμοθετημένης, και εξαιρετικά αυστηρής, ευρωπαϊκής μάσκας εκπομπής. / The multitude of applications that Ultra-Wideband (UWB) technology can serve, from high-speed Wireless Personal Area Networks, to Wireless Sensor Networks with precision Geolocation abilities, and Wireless Medical Networks, has attracted intense research interest in the implementation of UWB systems. The unusually wide range of frequencies assigned to UWB, from 3.1-10.6 GHz, allows UWB systems employing low order modulation schemes to enjoy high throughput at low power consumption. However, since UWB shares the spectrum with existing wireless networking technologies, UWB emissions must be limited to a power spectral density below the threshold of -41.3 dBm/MHz, satisfying very stringent emission masks and introducing great challenges in the design of UWB transmitters. The subject of this thesis is the design of low power, fully integrated, reconfigurable CMOS UWB transmitters, with high spectral flexibility, high speed and high modulation quality. Adopting the Multi-Band Impulse-Radio architecture, in conjunction with the Direct Sequence BPSK modulation, the research focused on the development of a baseband unit, able to precisely invert Gaussian shaped, subnanosecond pulses. The key contributions of this thesis are a CMOS Gaussian Pulse Generator and a BSPK modulation topology, which jointly constitute the proposed baseband unit. The Pulse Generator (PG) is based on non-linear shaping, so as to facilitate the configurability of the output pulse duration, and exploits the voltage transfer characteristic of a Resistive Loaded Asymmetrical CMOS Inverter, which results in spectral sidelobes typically better than -40 dB. The PG incorporates mostly-digital low voltage circuits, while the MOSFET devices that undertake the pulse shaping avoid exclusive operation in weak inversion, in contrast to previous implementations. Consequently, the proposed CMOS PG is able to support higher throughput, as well as higher output amplitude, which relaxes considerably the design of the RF front end. This thesis presents a systematic design procedure and a scaling analysis of the non-linear pulse shaper. Moreover, in order to further increase the speed, a special PRF boost technique is proposed, which trades off speed and spectral efficiency for the spectral sidelobes level. Regarding the BPSK modulator, this work introduces the “Trigger Switching Fully Balanced Up-Conversion” topology, which avoids the use of power-hungry and distortion-prone analog circuits for the accurate inversion of the subnanosecond shaped pulses, as well as avoids the application of analog waveform switching to the baseband pulses, since the baseband modulation takes place before the generation of the pulses. The digital nature of the switching lends itself to high data rates, while the balanced paths of the topology ensure high modulation quality with minimal design effort. Wafer probing measurements confirmed the high performance of the baseband unit. The functionality of the transmitter was completed by the development of an RF front end which consists of a double balanced mixer, an LO buffer, a differential to single-ended (DtoSE) converter, and a power amplifier which is ready to drive a 50 Ohms load without requiring any off-chip components. The integrated transmitter, which incorporates the proposed baseband unit and the RF front end, was fabricated in 130 nm CMOS technology. The transmitter RFIC was directly attached to the system RF PCB using the Chip-on-Board packaging option. The First-Pass success of the system was ensured by paying particular attention to Signal/Power Integrity issues and following an IC-Package-PCB co-design procedure. The transmitter was measured up to 1.5 Gbps, which, to the author’s knowledge, was the highest speed amongst the competitive Multi-Band Impulse-Radio UWB implementations in the literature. The corresponding energy efficiency was 21 pJoule/bit and the Error Vector Magnitude (EVM) 5.5%, while the proposed transmitter improved the spectral sidelobes by over 10 dB. Exploiting the reconfigurability of the transmitter, this thesis presents the first measurements at multi-Mbps speeds that completely meet the final version of the European spectrum emission mask.