Spelling suggestions: "subject:"state Of eharge anestimation"" "subject:"state Of eharge 3destimation""
1 |
State-of-Charge Estimation Method for LiFePO4 Electric Vehicle BatteriesChen, Kai-Jui 11 September 2012 (has links)
Battery is the sole electrical energy source when electric vehicle(EV) is moving.
To reduce traveling anxiety, an effective energy management system to indicate the state-of-charge (SOC) of the battery and make a balance between vehicle performance and endurance is very important. This research is aimed to develop a SOC estimation system with high accuracy. The proposed method in this thesis is based on under load voltage and multilevel Peukert's equation to estimate the SOC.
The proposed method is compared with the open circuit voltage method for initial SOC estimation and with coulometric method for cumulative SOC estimation under various EV driving conditions simulated by an adjustable electronics load. Experimental results indicate that the proposed method can provide reasonable accuracy as compared with other tested methods for LiFePO4 battery SOC estimations.
|
2 |
A BI-DIRECTIONAL ACTIVE CELL BALANCING OPTIMIZATION BASED ON STATE-OF-CHARGE ESTIMATIONZhang, Xiaowei January 2017 (has links)
Recently, Electric Vehicles (EVs) have received extensive consideration since they offer a more sustainable and greener transportation alternative compared to fossil-fuel propelled vehicles. Lithium-ion batteries are increasingly being considered in EVs due to their high energy density, slow loss of charge when not in use, and for lack of hysteresis effect. Conventionally, the batteries are connected in series to achieve the load voltage requirements. However, for the batteries with intrinsic discrepancies or different initial states, cell balancing is a concern because it is the weakest cell that determines the empty point for the battery and an undercharged series cell will shorten the lifetime of the entire pack. The imbalance potential of the battery behaves as the way of State-of-Charge (SOC) mismatch and it’s also temperature dependent. Therefore, in this thesis, an active cell balancing optimization was proposed and conducted in MATLAB to optimize battery unused capacity and thermal effect simultaneously based on bi-directional balancing system and pre-estimated SOC. The bi-directional balancing system was physically built based on “Fly-back” converter to compare balancing performance in discharging, idle, and plug-in charging mode. Moreover, a battery combined model worked collaboratively with robust state and parameter estimation strategies, namely Extended Kalman Filter (EKF) and Smooth Variable Structure Filter (SVSF) in order to estimate SOC for cell balancing. As a result, the proposed method can effectively optimize SOC mismatch around 2.5%. Meanwhile, more uniform temperature was achieved and the maximum temperature can be reduced about 7 ℃. / Thesis / Master of Applied Science (MASc)
|
3 |
Comparison of Nonlinear Filtering Methods for Battery State of Charge EstimationZhang, Klaus 13 August 2014 (has links)
In battery management systems, the main figure of merit is the battery's SOC, typically obtained from voltage and current measurements. Present estimation methods use simplified battery models that do not fully capture the electrical characteristics of the battery, which are useful for system design. This thesis studied SOC estimation for a lithium-ion battery using a nonlinear, electrical-circuit battery model that better describes the electrical characteristics of the battery. The extended Kalman filter, unscented Kalman filter, third-order and fifth-order cubature Kalman filter, and the statistically linearized filter were tested on their ability to estimate the SOC through numerical simulation. Their performances were compared based on their root-mean-square error over one hundred Monte Carlo runs as well as the time they took to complete those runs. The results show that the extended Kalman filter is a good choice for estimating the SOC of a lithium-ion battery.
|
4 |
Real-time estimation of state-of-charge using particle swarm optimization on the electro-chemical model of a single cellChandra Shekar, Arun 05 1900 (has links)
Indiana University-Purdue University Indianapolis (IUPUI) / Accurate estimation of State of Charge (SOC) is crucial. With the ever-increasing usage of batteries, especially in safety critical applications, the requirement of accurate estimation of SOC is paramount. Most current methods of SOC estimation rely on data collected and calibrated offline, which could lead to inaccuracies in SOC estimation as the battery ages or under different operating conditions. This work aims at exploring the real-time estimation and optimization of SOC by applying Particle Swarm Optimization (PSO) to a detailed electrochemical model of a single cell. The goal is to develop a single cell model and PSO algorithm which can run on an embedded device with reasonable utilization of CPU and memory resources and still be able to estimate SOC with acceptable accuracy. The scope is to demonstrate the accurate estimation of SOC for 1C charge and discharge for both healthy and aged cell.
|
5 |
Identification and State Estimation for Linear Parameter Varying Systems with Application to Battery Management System DesignHu, Yiran 07 October 2010 (has links)
No description available.
|
6 |
Modellierung und Ladezustandsdiagnose von Lithium-Ionen-ZellenBartholomäus, Ralf, Wittig, Henning 28 February 2020 (has links)
In diesem Beitrag wird ein neuer Ansatz zur Modellierung von Lithium-Ionen-Zellen vorgestellt, bei dem neben einem Modell zur Beschreibung des Nominalverhaltens der Zelle ein Unbestimmtheitsmodell parametriert wird, welches die unvermeidbare Abweichung zwischen dem Nominalmodell und dem tatsächlichen Zellverhalten quantifiziert. Für diese Modellbeschreibung wird ein neuer Algorithmus zur Ladezustandsdiagnose entwickelt, der anstelle eines einzelnen (fehlerbehafteten) Wertes für den Ladezustand ein Vertrauensintervall angibt sowie Artefakte im zeitlichen Verlauf des geschätzten Ladezustandes vermeidet. Die Eigenschaften der Ladezustandsschätzung werden an einer Lithium-Ionen-Zelle und einem Einsatzszenario aus dem automobilen Bereich demonstriert. / In this paper, a new approach to modeling lithium ion cells is presented. In addition to a model that describes the nominal behavior of the cell, an uncertainty model is parameterized which quantifies the unavoidable difference between the nominal model and the true system behavior. For this model description a new algorithm for state of charge estimation is developed, which provides a confidence interval instead of a single unreliable value for the state of charge and avoids artifacts in the progression of the estimated state of charge over time. The properties of the state of charge estimation are demonstrated on a lithium-ion cell in an automotive application scenario.
|
7 |
Impact of Charge Profile on Battery Fast Charging Aging and Dual State Estimation Strategy for Traction ApplicationsDa Silva Duque, Josimar January 2021 (has links)
The fast-growing electric vehicles (EVs) market demands huge efforts from car manufacturers to develop and improve their current products’ systems. A fast charge of the battery pack is one of the challenges encountered due to the battery limitations regarding behaviour and additional degradation when exposed to such a rough situation. In addition, the outcome of a study performed on a battery does not apply to others, especially if their chemistries are different. Hence, extensive testing is required to understand the influence of design decisions on the particular energy storage device to be implemented. Due to batteries’ nonlinear behaviour that is highly dependent on external variables such as temperature, the dynamic load and aging, another defying task is the widely studied state of charge (SOC) estimation, commonly considered one of the most significant functions in a battery management system (BMS).
This thesis presents an extensive battery fast charging aging test study equipped with promising current charging profiles from published literature to minimize aging. Four charging protocols are carefully designed to charge the cell from 10 to 80% SOC within fifteen minutes and have their performances discussed. A dual state estimation algorithm is modelled to estimate the SOC with the assistance of a capacity state of health (SOHcap) estimation. Finally, the dual state estimation model is validated with the fast charging aging test data. / Thesis / Master of Science in Mechanical Engineering (MSME)
|
8 |
Deep Neural Networks for Improved Terminal Voltage and State-of-Charge Estimation of Lithium-Ion Batteries for Traction ApplicationsGoncalves Vidal, Carlos Jose January 2020 (has links)
The growing interest in more electrified vehicles has been pushing the industry and academia to pursue new and more accurate ways to estimate the xEV batteries State-of-Charge (SOC). The battery system still represents one of the many technical barriers that need to be eliminated or reduced to enable the proliferation of more xEV in the market, which in turn can help reduce CO2 emissions. Battery modelling and SOC estimation of Lithium-ion batteries (Li-ion) at a wide temperature range, including negative temperatures, has been a challenge for many engineers.
For SOC estimation, several models configurations and approaches were developed and tested as results of this work, including different non-recurrent neural networks, such as Feedforward deep neural networks (FNN) and recurrent neural networks based on long short-term memory recurrent neural networks (LSTM-RNN). The approaches have considerably improved the accuracy presented in the previous state-of-the-art. They have expanded the application throughout five different Li-ion at a wide temperature range, achieving error as low as 0.66% Root Mean Square Error at -10⁰C using an FNN approach and 0.90% using LSTM-RNN. Therefore, the use of deep neural networks developed in this work can increase the potential for xEV application, especially where accuracy at negative temperatures is essential.
For Li-ion modelling, a cell model using LSTM-RNN (LSTM-VM) was developed for the first time to estimate the battery cell terminal voltage and is compared against a gated recurrent unit (GRU-VM) approach and a Third-order Equivalent Circuit Model based on Thevenin theorem (ECM). The models were extensively compared for different Li-ion at a wide range of temperature conditions. The LSTM-VM has shown to be more accurate than the two other benchmarks, where could achieve 43 (mV) Root Mean Square Error at -20⁰C, a third when compared to the same situation using ECM. Although the difference between LSTM-VM and GRU-VM is not that steep.
Finally, throughout the work, several methods to improve robustness, accuracy and training time have been introduced, including Transfer Learning applied to the development of SOC estimation models, showing great potential to reduce the amount of data necessary to train LSTM-RNN as well as improve its accuracy. / Thesis / Doctor of Philosophy (PhD) / For electric vehicle State-of-Charge estimation, several models configurations and approaches were developed and tested as results of this work, including different non-recurrent neural networks, such as Feedforward deep neural networks (FNN) and recurrent neural networks based on long short-term memory recurrent neural networks (LSTM-RNN). The approaches have considerably improved the accuracy presented in the previous state-of-the-art. They have expanded the application throughout five different Li-ion at a wide temperature range, achieving error as low as 0.66% Root Mean Square Error at -10⁰C using an FNN approach and 0.90% using LSTM-RNN. Therefore, the use of deep neural networks developed in this work can increase the potential for xEV application, especially where accuracy at negative temperatures is essential.
For Li-ion modelling, a cell model using LSTM-RNN (LSTM-VM) was developed for the first time to estimate the battery cell terminal voltage and is compared against a gated recurrent unit (GRU-VM) approach and a Third-order Equivalent Circuit Model based on Thevenin theorem (ECM). The models were extensively compared for different Li-ion at a wide range of temperature conditions. The LSTM-VM has shown to be more accurate than the two other benchmarks, where could achieve 43 (mV) Root Mean Square Error at -20⁰C, a third when compared to the same situation using ECM. Although the difference between LSTM-VM and GRU-VM is not that steep.
|
9 |
In-Situ Capacity and Resistance Estimation Algorithm Development for Lithium-Ion Batteries Used in Electrified VehiclesVaria, Adhyarth C. January 2014 (has links)
No description available.
|
10 |
Modeling and State of Charge Estimation of Electric Vehicle BatteriesAhmed, Ryan January 2014 (has links)
Electric vehicles have received substantial attention in the past few years since they provide a more sustainable, efficient, and greener transportation alternative in comparison to conventional fossil-fuel powered vehicles. Lithium-Ion batteries represent the most important component in the electric vehicle powertrain and thus require accurate monitoring and control. Many challenges are still facing the mass market production of electric vehicles; these challenges include battery cost, range anxiety, safety, and reliability. These challenges can be significantly mitigated by incorporating an efficient battery management system. The battery management system is responsible for estimating, in real-time, the battery state of charge, state of health, and remaining useful life in addition to communicating with other vehicle components and subsystems. In order for the battery management system to effectively perform these tasks, a high-fidelity battery model along with an accurate, robust estimation strategy must work collaboratively at various power demands, temperatures, and states of life. Lithium ion batteries are considered in this research. For these batteries, electrochemical models represent an attractive approach since they are capable of modeling lithium diffusion processes and track changes in lithium concentrations and potentials inside the electrodes and the electrolyte. Therefore, electrochemical models provide a connection to the physical reactions that occur in the battery thus favoured in state of charge and state of health estimation in comparison to other modeling techniques.
The research presented in this thesis focuses on advancing the development and implementation of battery models, state of charge, and state of health estimation strategies. Most electrochemical battery models have been verified using simulation data and have rarely been experimentally applied. This is because most electrochemical battery model parameters are considered proprietary information to their manufacturers. In addition, most battery models have not accounted for battery aging and degradation over the lifetime of the vehicle using real-world driving cycles. Therefore, the first major contribution of this research is the formulation of a new battery state of charge parameterization strategy. Using this strategy, a full-set of parameters for a reduced-order electrochemical model can be estimated using real-world driving cycles while accurately calculating the state of charge. The developed electrochemical model-based state of charge parameterization strategy depends on a number of spherical shells (model states) in conjunction with the final value theorem. The final value theorem is applied in order to calculate the initial values of lithium concentrations at various shells of the electrode. Then, this value is used in setting up constraints for the optimizer in order to achieve accurate state of charge estimation. Developed battery models at various battery states of life can be utilized in a real-time battery management system. Based on the developed models, estimation of the battery critical surface charge using a relatively new estimation strategy known as the Smooth Variable Structure Filter has been effectively applied. The technique has been extended to estimate the state of charge for aged batteries in addition to healthy ones.
In addition, the thesis introduces a new battery aging model based on electrochemistry. The model is capable of capturing battery degradation by varying the effective electrode volume, open circuit potential-state of charge relationship, diffusion coefficients, and solid-electrolyte interface resistance. Extensive experiments for a range of aging scenarios have been carried out over a period of 12 months to emulate the entire life of the battery. The applications of the proposed parameterization method combined with experimental aging results significantly improve the reduced-order electrochemical model to adapt to various battery states of life. Furthermore, online and offline battery model parameters identification and state of charge estimation at various states of life has been implemented. A technique for tracking changes in the battery OCV-R-RC model parameters as battery ages in addition to estimation of the battery SOC using the relatively new Smooth Variable Structure Filter is presented. The strategy has been validated at both healthy and aged battery states of life using driving scenarios of an average North-American driver. Furthermore, online estimation of the battery model parameters using square-root recursive least square (SR-RLS) with forgetting factor methodology is conducted. Based on the estimated model parameters, estimation of the battery state of charge using regressed-voltage-based estimation strategy at various states of life is applied.
The developed models provide a mechanism for combining the standalone estimation strategy that provide terminal voltage, state of charge, and state of health estimates based on one model to incorporate these different aspects at various battery states of life. Accordingly, a new model-based estimation strategy known as the interacting multiple model (IMM) method has been applied by utilizing multiple models at various states of life. The method is able to improve the state of charge estimation accuracy and stability, when compared with the most commonly used strategy. This research results in a number of novel contributions, and significantly advances the development of robust strategies that can be effectively applied in real-time on-board of a battery management system. / Thesis / Doctor of Philosophy (PhD)
|
Page generated in 0.1234 seconds