Dampening systems are important in heavy vehicles utilized in rough terrains, with purpose to reduce shocks and vibrations with negative influences on the vehicle and, more importantly, on the operator of the vehicle. During the years the heavy vehicles require sturdier construction parts, due to demands on higher load capacity, where the easy solution to scale up the construction parts is not always applicable for dampening systems with nonlinear behavior. Hence, the sturdiness in the design of these dampening systems requires improvement. In this thesis the design of the rubber spring used as rubber spring in Volvo’s articulated hauler A40G is treated. The aim of this thesis is to find alternative design solutions on the rubber spring, improving its lifetime. The usual failure of these rubber springs is crack propagation in the rubber body. In the method of this thesis, alternative design solution are generated in concepts though brain storming, which are adjusted to achieve the desired behavior of the rubber spring through calculations and tested in performance through simulations in Abaqus. From analyzing the generated data, it is concluded that among the tested design solutions, a combination of fewer plates and shaping the plates as thin bowls, results in highest potential increase in lifetime.

No description available.

The dissertation starts from the understanding of dislocation dissipation mechanism due to the image force acting on the dislocation. This work implements a screw dislocation in solids with free surfaces by a novel finite element model, and then image forces of dislocations embedded in various shaped GaN nanorods are calculated. As surface stress could dramatically influence the behavior of nanostructures, this work has developed a novel analytical framework to solve the stress field of solids with dislocations and surface stress. It is successfully implemented in this framework for the case of isotropic circular nanowires (2D) and the analytical result of the image force has been derived afterwards. Based on the finite element analysis and the analytical framework, this work has a semi-analytical solution to the image force of isotropic nanorods (3D) with surface stress. The influences of the geometrical parameter and surface stress are illustrated and compared with the original finite element result. In continuation, this work has extended the semi-analytical approach to the case of anisotropic GaN nanorods. It is used to analyze image forces on different dislocations in GaN nanorods oriented along polar (c-axis) and non-polar (a, m-axis) directions. This work could contribute to a wide range of nanostructure design and fabrication for dislocation-free devices.

No description available.

This thesis presents an exploration of the photophysics of colloidal semiconductor nanocrystals using both linear and non-linear optical measurement techniques. These optical methodologies are used to follow population dynamics in both singly and multiply excited nanocrystal systems as well as determine material properties of the ensemble. Topics covered in the thesis include, the identification and characterization of bulk-like nanocrystals, study of the fine structure states of the lowest energy exciton, single and multiexciton population dynamics, acoustic phonon modes, elasticity and surface stress properties of a colloidal ensemble in solution.Through linear spectroscopy, the properties of both quantum confined and bulk-like colloidal semiconductor nanocrystals are compared. The identification of a model system of bulk-like nanocrystals with a non-standard absorption profile serves to resolve an ambiguity in literature concerning their characterization. The remainder of the thesis is focused on the size-dependent properties of quantum confined CdSe colloidal nanocrystals. The population dynamics and material properties of these systems are studied using a nonlinear optical technique called transient grating. A third order transient grating measurement with a cross-polarized configuration, which follows the relaxation within the fine structure levels of the lowest energy exciton state, is demonstrated and used to compare systems with different crystal field splittings. Transient grating experiments performed with specific polarization sequences allow for selective observation of the dynamics amongst nearly degenerate levels at room temperature. Cross-polarized transient grating is also used to observe a quantized acoustic phonon mode in a series of nanocrystal samples. The observation of this mode allows experimental determination of the elasticity and surface stress of the nanocrystal ensemble in solution. The anisotropic origin of the acoustic phonon is discussed using a combination of theoretical analysis, modelling and experimental data. In addition, third- and fifth-order transient grating experiments are used to study exciton and multiexciton population relaxation dynamics. The work presented here spans the optical and material properties of quantum confined and `bulk' nanocrystals. This thesis attempts to illustrate the broad scope of the observed behaviour of colloidal nanocrystal systems and to contribute to a greater understanding of their physical properties.

This thesis presents an exploration of the photophysics of colloidal semiconductor nanocrystals using both linear and non-linear optical measurement techniques. These optical methodologies are used to follow population dynamics in both singly and multiply excited nanocrystal systems as well as determine material properties of the ensemble. Topics covered in the thesis include, the identification and characterization of bulk-like nanocrystals, study of the fine structure states of the lowest energy exciton, single and multiexciton population dynamics, acoustic phonon modes, elasticity and surface stress properties of a colloidal ensemble in solution.Through linear spectroscopy, the properties of both quantum confined and bulk-like colloidal semiconductor nanocrystals are compared. The identification of a model system of bulk-like nanocrystals with a non-standard absorption profile serves to resolve an ambiguity in literature concerning their characterization. The remainder of the thesis is focused on the size-dependent properties of quantum confined CdSe colloidal nanocrystals. The population dynamics and material properties of these systems are studied using a nonlinear optical technique called transient grating. A third order transient grating measurement with a cross-polarized configuration, which follows the relaxation within the fine structure levels of the lowest energy exciton state, is demonstrated and used to compare systems with different crystal field splittings. Transient grating experiments performed with specific polarization sequences allow for selective observation of the dynamics amongst nearly degenerate levels at room temperature. Cross-polarized transient grating is also used to observe a quantized acoustic phonon mode in a series of nanocrystal samples. The observation of this mode allows experimental determination of the elasticity and surface stress of the nanocrystal ensemble in solution. The anisotropic origin of the acoustic phonon is discussed using a combination of theoretical analysis, modelling and experimental data. In addition, third- and fifth-order transient grating experiments are used to study exciton and multiexciton population relaxation dynamics. The work presented here spans the optical and material properties of quantum confined and `bulk' nanocrystals. This thesis attempts to illustrate the broad scope of the observed behaviour of colloidal nanocrystal systems and to contribute to a greater understanding of their physical properties.

Interface balance laws are derived to describe transport across a phase interface. This is used to derive generalized conditions for phase nucleation and growth, valid even for solids with inhomogeneous surface stress.<div><br></div><div>An explicit interface tracking approach called Enriched Isogeometric Analysis (EIGA) is used to simulate phase evolution. Algebraic level sets are used as a measure of distance and for point projection, both necessary operations in EIGA. Algebraic level sets are observed to often fail for surfaces. Rectification measures are developed to make algebraic level sets more robust and applicable for general surfaces. The proposed methods are demonstrated on electromigration problems. The simulations are validated by modeling electromigration experiments conducted on Cu-TiN line structures.</div><div><br></div><div>To model topological changes, common in phase evolution problems, Boolean operations are performed on the algebraic level sets using R-functions. This is demonstrated on electromigration simulations on solids with multiple voids, and on a bubble coalescence problem. </div>

Microcantilevers have been investigated as high sensitivity, label free biosensors for approximately 15 years. In nearly all cases, a thin gold film deposited on the microcantilevers is used as an intermediate attachment layer because of the convenience of thiol-gold chemistry. Unfortunately, this attachment chemistry can be unstable when used with complex sample media such as blood plasma. The Nordin group at BYU has recently developed an all-silicon in-plane photonic microcantilever (PMCL) technology to serve as a platform for label-free biosensing. It has the advantage of being readily scalable to simultaneous readout of many PMCLs in array format, and allows integration with polymer microfluidics to facilitate the introduction of biological samples and reagents. An essential processing step for the transformation of the PMCL into a practical biosensor is the ability to effectively immobilize active biological receptors directly on silicon PMCL surfaces such that ligand binding generates sufficient surface stress to cause measureable PMCL deflection. This dissertation presents the development of a method to functionalize the sensor surface of all-silicon in-plane photonic microcantilever (PMCL) arrays. This method employs a materials inkjet printer for non-contact jetting and a fluid that is custom designed for ink-jetting and biological applications with approximately 1 pL droplet size. The method facilitates the application of different receptors on select PMCLs with drop placement accuracy in the +/- 7.5 μm range. The functionalization fluid facilitates further processing using humidity control to achieve full coverage of only the PMCL's top surface and removal of dissolved salts to improve uniformity of receptor coverage and to prevent fouling of the sensor surface. Once a functionalization method was successfully developed, a series of experiments were performed to investigate the amount of surface stress that can be generated when receptors are immobilized directly to the silicon surface. In one series of experiments, a 4.8 μM streptavidin solution was used with biotin immobilized on multiple PMCLs to demonstrate adsorption-induced surface stress and concomitant deflection of the PMCL. The group observed ~ 15 nm PMCL deflection on average, with a corresponding surface stress of approximately 4 mN/m. These experiments yield the sensor response in real-time and employ a combination of multiple PMCLs functionalized as either sensors or unfunctionalized to serve as references. Investigation of various attachment chemistries is included, as well as a comparison with and without passivation of non-sensor surfaces. Investigated passivation strategies prevented ligand binding from generating a differential surface stress. Failure modes and physical mechanisms for adsorption-induced surface stress are discussed. Immobilization and passivation strategies for antibody-based biosensing are demonstrated with fluorescence microscopy and a corresponding PMCL sensing experiment using rabbit anti-goat F(ab') fragments as the receptors and Alex Fluor 488 labeled goat anti-rabbit IgGs as the ligand. While the results of these experiments remain inconclusive, suggestions for future research involving the PMCL sensor array are recommended.

No description available.

Les microcantileviers fonctionnalisés offrent une plateforme idéale pour la nano- et micro-mécanique et pour le développement de (bio-) capteurs tres sensible. Le principe d’opération consiste dans des évènements physicochimiques qui se passent du côté fonctionnalisé du microcantilevier induisant une différence de stress de surface entre les deux côtés du cantilevier qui cause une déflexion verticale du levier. Par contre, les facteurs et les phénomènes interfacials qui régissent la nature et l'intensité du stress de surface sont encore méconnus. Pour éclaircir ce phénomène, la première partie de cette thèse porte sur l'étude des réactions de microcantileviers qui sont recouverts d'or et fonctionnalisés par une monocouche auto-assemblée (MAA) électroactive. La formation d'une MAA de ferrocènylundécanethiol (FcC11SH) à la surface d'or d'un microcantilevier est le modèle utilisé pour mieux comprendre le stress de surface induit par l’électrochimie. Les résultats obtenus démontrent qu'une transformation rédox de la MAA de FcC11SH crée un stress de surface qui résulte dans une déflexion verticale du microcantilevier. Dépendamment de la flexibilité du microcantilevier, cette déflexion peut varier de quelques nanomètres à quelques micromètres. L’oxydation de cette MAA de FcC11SH dans un environnement d'ions perchlorate génère un changement de stress de surface compressive. Les résultats indiquent que la déflexion du microcantilevier est due à une tension latérale provenant d'une réorientation et d'une expansion moléculaire lors du transfért de charge et de pairage d’anions. Pour vérifier cette hypothèse, les mêmes expériences ont été répéteés avec des microcantileviers qui ont été couverts d'une MAA mixte, où les groupements électroactifs de ferrocène sont isolés par des alkylthiols inactifs. Lorsqu’un potentiel est appliqué, un courant est détecté mais le microcantilevier ne signale aucune déflexion. Ces résultats confirment que la déflexion du microcantilevier est due à une pression latérale provenant du ferrocènium qui se réorganise et qui crée une pression sur ses pairs avoisinants plutôt que du couplage d’anions. L’amplitude de la déflexion verticale du microcantilevier dépend de la structure moléculaire de la MAA et du le type d’anion utilisés lors de la réaction électrochimique. Dans la prochaine partie de la thèse, l’électrochimie et la spectroscopie de résonance de plasmon en surface ont été combinées pour arriver à une description de l’adsorption et de l’agrégation des n-alkyl sulfates à l’interface FcC11SAu/électrolyte. À toutes les concentrations de solution, les molécules d'agent tensio-actif sont empilées perpendiculairement à la surface d'électrode sous forme de monocouche condensé entrecroisé. Cependant, la densité du film spécifiquement adsorbé s'est avérée être affectée par l'état d'organisation des agents tensio-actifs en solution. À faible concentration, où les molécules d'agent tensio-actif sont présentes en tant que monomères solvatés, les monomères peuvent facilement s'adapter à l’évolution de la concentration en surface du ferrocènium lors du balayage du potential. Cependant, lorsque les molécules sont présentes en solution en tant que micelles une densité plus faible d'agent tensio-actif a été trouvée en raison de l'incapacité de répondre effectivement à la surface de ferrocenium générée dynamiquement. / Surface-functionalized microcantilevers provide an ideal platform for nano- and micro-mechanical actuation and highly sensitive sensing technologies. The basic principle of operation is that a chemical or physical event occurring at the functionalized surface of one side of the cantilever generates a surface stress difference (between the active functionalized and passive non-functionalized sides) that causes the cantilever to bend away from its resting position. However, the factors and phenomena contributing to both the nature and magnitude of the surface stress are not well understood. To this end, the first part of this thesis focused on investigating the potential-controlled actuation and surface stress properties of free-standing gold-coated microcantilevers functionalized with a redox-active self-assembled monolayer (SAM). A ferrocenylundecanethiolate (FcC11SAu) SAM on a gold-coated cantilever was used as a model system to investigate the surface stress generated by faradaic chemistry. The data obtained clearly demonstrates that the electrochemical transformation of a ferrocene moiety in a monomolecular organic film can generate a surface stress change of sufficient magnitude to deflect a microcantilever. In fact, depending on the flexibility of the microcantilever, the mechanical deflection resulting from the redox transformation of the surface-tethered ferrocene can range on the order of nanometers to micrometers. The oxidation of the FcC11SAu SAM in perchlorate electrolyte generates a compressive surface stress change. The microcantilever deflection is driven by the lateral tension resulting from molecular reorientation/volume expansion accompanying the charge-transfer and ion-pairing events. To verify this hypothesis, mixed SAM-modified microcantilevers, in which the electroactive ferrocenes are isolated from one another by an inert n-alkylthiolate matrix, were investigated. Under an applied potential, a Faradaic current was measured, but no microcantilever beam deflection was observed. This finding confirms that the cantilever responds to the lateral pressure exerted by an ensemble of re-orienting ferrocenium-bearing alkylthiolates upon each other rather than to individual anion pairing events. Changes in molecular structure and anion type can also be used to modulate the extent of micromechanical motion. In the next part of the dissertation, electrochemical measurements and surface plasmon resonance spectroscopy were combined to present a description of the adsorption and aggregation of n-alkyl sulfates at the FcC11SAu/electrolyte interface. At all bulk solution concentrations, the surfactant moieties packed perpendicular to the electrode surface in the form of an interdigitated condensed film. However, the density of the specifically adsorbed film was found to be affected by the organizational state of the surfactants in solution. At low concentrations, where the surfactant molecules are present as solvated monomers, the monomers can readily adapt to the changing ferrocenium concentration with the potential potential scan. However, when the molecules are present as micellar structures in solution, a lower surfactant packing density was found because of the inability to respond effectively to the dynamically generated surface ferroceniums. This research demonstrates the potential utility of charge-transfer interactions for organizing materials at solid interfaces and effecting micromechanical actuation using an electrifical stimulus.