This thesis describes the implementation of microprocessor controlled single-phase and three-phase inverters for UPS applications. A carrier frequency of 18 kHz is employed in both cases, and the PWM pulses are generated directly by the microprocessor using the regular-sampled symmetric PWM strategy. Single-edge modulation as well as double-edge modulation has been implemented for single-phase and three-phase systems. Since in general, software implementation of PWM strategies require precalculated pulse width values, a scheme is proposed which enables the large quantity of such data to be handled efficiently. The scheme involves the use of a small program for calculating and transferring the data to the memory of the controller.

Thesis (M. Tech. Engineering: Electrical--Vaal University of Technology / A high-power Mosfet was incorporated as a switching device into the efficient Class E configuration, where the switching device switches current through itself either completely on or completely off at high frequencies. The first objective of this project was to demonstrate the effectiveness of a phase-lock loop circuit in generating stable high frequencies when connected in an indirect frequency synthesizer configuration. The indirect frequency synthesizer has established itself as a versatile frequency generator capable of generating high frequencies based on a lower stable reference frequency. The frequency generation stage incorporates a phaselock loop circuit, a frequency divider and a stable reference frequency section. The phase-lock loop section incorporates the TTL based 74HC 4046 that is based upon the common CMOS 4046 integrated circuit. The frequency divider section is built around the CMOS-based 4526 whilst the reference frequency section incorporates the CMOS-based 4060. The frequency synthesizer produced a range of frequencies from 50 kHz to 8 MHz in 50 kHz steps. The output voltage was constant at 5,5 V. The second objective was to show that the complementary emitter follower is indeed a worthy Mosfet gate drive circuit at high frequencies. The Mosfet driver stage produced a voltage signal of at least 11 V, being able to source and sink relatively high peaks of current, especially at high frequencies. Voltage amplification occurred through the use of multiple CMOS-based 40106 inverters. The complementary emitter follower, known for its low output impedance and its ability to source and sink large amounts of current, was an important component in the final Mosfet gate section.

The unique features of flexoelectric and dielectric effects are investigated, and exploited for a variety of functions, in a wide range of helicoidal liquid crystal systems, including non-chiral, cholesteric and blue phases. Electrooptic techniques are developed to measure flexoelectric parameters in non-chiral and cholesteric liquid crystals using twisted nematic and Grandjean geometries respectively. A crystal rotation method, and using a lock-in amplifier, is used to enable the measurement of a very small e/K of 0.011 C/N^-1m^-1. Enhancement in chiral-flexoelectric switching is demonstrated theoretically in liquid crystals with negative dielectric anisotropy and in systems in which the pitch is constrained to be other than the natural pitch. A methodological framework for inducing stable Uniform Lying Helix alignment is developed based on weak homeotropic alignment conditions and a method to bias the helicoidal axis orientation; a series of approaches within this framework are demonstrated, including nano-grooved interfaces, periodic boundaries conditions, in-plane fields, and mould-templated micro-channels. The latter approach is potentially commercially viable for sub-millisecond electrooptic technology. The contribution to a cholesteric material's effective dielectric permittivity of flexoelectric polarization is formulated, and an ability to switch a cholesteric between Grandjean and lying-helix configurations based on the dispersion in the flexoelectric polarization and resultant relaxation in dielectric properties is demonstrated. The flexoelectric contribution to dielectric permittivity is exploited to enable switching in bistable reflective displays and alignment of the Uniform Lying Helix. The existence of a flexoelectric contribution to Kerr switching in blue phases is demonstrated, and a semi-empirical model for the effect is developed. The effect is the first known example of a non-polar flexoelectrooptic effect. Independent flexoelectric and dielectric contributions to Kerr switching in blue phases are measured experimentally by measuring the induced birefringence as a function of driving frequency in flexoelectric- and dielectric-dominated wide-temperature-range blue phase materials.

The thesis discuses an integration of photovoltaic power stations to electric network. The first part describes connecting conditions of small sources to distribution system, including administrative requirements, feasibility study, and requirements to the energy meters, measuring, control devices, switching devices and protection. The second part is aimed to describe problems of the photovoltaic system. Solar radiation generating and reducing of its intensity incident upon the earth surface are described in this part. The quantum of produced electric power depends on climatic conditions in the fixed area, seasons, etc. This work also discusses the types of photovoltaic cells and their actual efficiency. Inverters are further important components of the photovoltaic system. The parameters of the inverters have a great influence on the total actual efficiency of the photovoltaic system. Different methods of the photovoltaic panels’ connection with the inverters and their advantages and disadvantages are also mentioned. The supporting structure of the photovoltaic panels and eventually transformer are further important components of photovoltaic system. The work also analyze the methods of connection of the photovoltaic power station to distributive low voltage and medium voltage network, electric energy accumulation and possibilities of the sale of produced electric energy. The large number of the connected photovoltaic power stations has negative influences to electric network. The third part contains the design of a photovoltaic power plant with a capacity of 516,24 kWp on the scoped area in southern Bohemia. The project documentation for the location where the power plant is designed is also made. It contains the design of photovoltaic panels, the design of the inverters to get an optimal power load. This part also contains a calculation of the photovoltaic system losses and the design of transformer and the cable junction calculation of the distributive system. The feasibility study of the power plant connected to distributive system is also conducted. Its delivery rate will be connected to the distribution point Řípov (110/22 kV). The calculation results show us that this photovoltaic power plant can be linked to the distribution system. The final part of this paper contains an economic estimate of the photovoltaic power plant operating and the calculation of the return. An Economic return is influenced by the wide range of values that affect the total return rate. The calculation of an operating economy is made for several variants. The return rate in refer to contemporary redemption price for 2010 with no consideration for a bank loan is 7 years. If we consider the bank loan it would be 12 years. The penetrative reduction of the redemption price is expected for 2011. Calculation works with the decline of 30 %. It would extend the rate of return to 11 years without a bank loan or to 22 years with the bank loan. The bank loan is considered to cover 80 % of the investment.