This thesis presents a research project aimed at advancing the treatment of cold-formed steel (CFS) structural reliability in roof trusses. Structural design today relies almost exclusively on component-level design, so structural safety is assured by limiting the probability of failure of individual components. Reliability of the entire system is typically not assessed, so in a worst-case scenario the system reliability may be less than the component reliability, or in a best-case scenario the system reliability may be much greater than the component reliability. A roof truss itself, is a subsystem with several possible failure modes that are being studied in this test program. These trusses are constructed of CFS members that nest with one another at the truss nodes and are connected by drilling fasteners through the mated surfaces, as well as having steel sheathing fastened to the top chords for lateral bracing. Presented in this paper is a series of full-scale static tests on single cold-formed steel roof trusses with a unique experimental setup. The test specimens were carefully monitored to address multiple failure modes: buckling of the top chord, buckling of the truss webs, and any connection failures. This research includes the experimental results, the computed system reliability of the trusses as well as their relationship between the components reliability.

Interconnection of DERs into the transmission lines is starting to take a substantial share of the total power capacity. Although the largest share of power generation attributes to coal and gas power plants, renewable energy is gradually increasing. However, in the past, the size of DERs was relatively smaller, and rooftop PV was the dominant renewable energy source. As a result, the studies for interconnection focused on those rooftop PVs on the distribution side. Since the scenario is slowly changing as more utilities increase the share of clean energy by building large-scale solar farms and wind farms, it is necessary to study the effect of those DERs in the transmission system. Among the various issues, this work focuses on the impact on a transmission system's voltage stability. When the voltage stability at a point in the system is compromised, it can affect the entire power system's overall security, quality, and reliability. Therefore, this work aims to assess the system's stress due to increased loading conditions and increased growth of DERs integration. A steady-state voltage stability index is used to generate a heat-map that identifies the areas where the system can go unstable in events like the loss of the renewable generation under a bus. The steady-state simulation is performed on the IEEE 14 bus system in Distributed Engineering Workstation (DEW) to find the system's weak links using the stability heat-map. DERs are added to the corresponding weak buses, and the improvement in the stability margin for various penetration levels are studied. The results obtained from the steady-state analysis are also verified using the dynamic simulation of the model using OpenModelica. / Master of Science / Transmission networks are going through some of the fundamental changes in how they are planned and operated as more and more renewable energy sources are connected to the grid. Unlike the traditional setup where the transmission line transfers bulk power from a large generator to the load center at a different location, the advent of renewable energy resources enables the power to be generated in distributed form. It allows electrical power to be generated closer to the demand. In the long run, the transmission system's stress reduces as a significant portion of demand is supplied locally. Thus, the distributed energy resources (DERs) in the power grid have the potential for substantial economic and environmental benefits. However, it can also bring about a range of challenges to the power system. Among the various issues, this work focuses on the effects on a transmission system's voltage stability. When the voltage stability at a point in the system is compromised, it can affect the entire power system. Therefore, this work aims to assess the stress on the system due to increased loading conditions and increased growth of DERs integration, utilizing a voltage stability index to identify the areas where the system can go unstable in events like the loss of renewable generation under a bus. The steady-state simulation is performed on the IEEE 14 bus system to find the weak links in the system where DERs can improve the system's stability. The results obtained from the steady-state analysis are verified using the dynamic simulation of the model.

No description available.

No description available.

The Web, being the most popular component of the Internet, has been transformed from a static information-serving medium into a fully interactive platform. This platform has been used by developers to create web applications rivaling traditional desktop systems. Designing, developing and evaluating these applications require new or modified methodologies, techniques and tools because of the different characteristics they exhibit. This dissertation discusses two important areas for developing and evaluating these applications: security and data mining. In the security area, a survey using a process similar to the Goal Question Metric approach examines the properties of web application vulnerabilities. Using results from the survey, a white-box approach to identify web applications vulnerabilities is proposed. Although the approach eliminates vulnerabilities during the development process, it does not protect existing web applications that have not utilized the approach. Hence, an Anomaly-based Network Intrusion Detection System, called AIWAS, is introduced. AIWAS protects web applications through the analysis of interactions between the users and the web applications. These interactions are classified as either benign or malicious; malicious interactions are prevented from reaching the web applications under protection. In the data mining area, the method of reliability estimation from server logs is examined in detail. This examination reveals the fact that the session workload is currently obtained using a constant Session Timeout Threshold (STT) value. However, each website is unique and should have its own STT value. Hence, an initial model for estimating the STT is introduced to encourage future research on sessions to use a customized STT value per website. This research on the STT leads to a deeper investigation of the actual session workload unit. More specifically, the distributional properties of the session workload are re-examined to determine whether the session workload can be described as a heavy-tailed distribution. / Software Engineering and Intelligent Systems

Large interruptions of power supply in the transmission system have considerable impact on modern society. The goal for the transmission system operator (TSO) is to prevent and mitigate such events with optimal decisions in design, planning, operation and maintenance. Identifying critical power components for system reliability provides one important input to this decision-making. This thesis develops quantitative component reliability importance indices applicable for identifying critical components in real transmission systems. Probabilistic models with component failure statistics are combined with detailed power system models evaluated with the AC power flow technique. In the presented method each system component is assigned three importance indices based on outage events expected probability and consequence to (i) reduced system security margin, (ii) interrupted load supply and (iii) disconnected generation units. By ranking components by each of the three interests, a more complete view of the risks to system reliability can be assessed than if, as traditionally, only (ii) is modelled. The impact on security margin is studied in well established critical transfer sections (CTS) supervised by the TSO. TSOs set the CTSs limits [MW] based on deterministic security criteria, with regard to thermal, voltage level, and system stability limits, and the CTSs' condition at post-contingency state is in the method used as an indicator of the system security margin. The methodology is extended with three indices modified to quantify the component importance for common-cause events initiated by acts of sabotage. The developed methods are applied on a significant part of the Great Britain transmission system, modelling 7000 components and 107 substation layouts. The study includes several load demand scenarios, 200 million initiating outage events and non-functioning protection equipment. The resulting component ranking provides an important input to the TSO's decision-making, and could be implemented as a complement to the existing deterministic N-1 criterion. With the methods applied a TSO can perform further and more detailed assessments on a few critical components in order to enhance system reliability for equipment failures and strengthen the system vulnerability against sabotage. / QC 20110920

An interesting alternative for today's high efficiency variable speed drives is the Permanent Magnet-Assisted Synchronous Reluctance Motor drive, which belongs to the family of brushless synchronous AC motor drives. Generally, the reluctance torque of this motor is significant compared to the Permanent Magnet electrical torque. The advantage of increased reluctance torque is the decreased need of expensive permanent magnet (PM) material, which makes this solution thus cheaper than the respective permanent magnet motor. Also due to its synchronous operation, sensorless rotational control is possible along with higher power factor and better efficiency compared to the induction motor (IM). Therefore, this thesis first deals with the implementation of a vector control strategy for speed control of the PMa-synRM motor that can be applied to a washing machine application. The machine is supplied by a current controlled voltage source PWM inverter to control the instantaneous stator currents which are decided by the reference speed. Secondly, the thesis focuses on the sensorless speed operation of the PMa-SynRM to take advantage of the lower costs as well as increased system reliability which otherwise is not possible using the delicate speed or position sensors. The concept involves estimation of the rotor speed and/or position. There are several speed estimation techniques proposed by researchers and among them the observer based technique is proven and commonly used in the industry. The only requirements of the observer system are a very fast signal processor, specialized and optimized to perform complex mathematical calculations. The feasibility and effectiveness of the control techniques are verified using the experimental results, implemented using the Texas Instruments TMS320F2812 eZDSP controller board and the overall motor drive system in the laboratory.

<p>In reregulated and restructured electricity markets the production and retail of electricity is conducted on competitive markets, the transmission and distribution on the other hand can be considered as natural monopolies. The financial regulation of Distribution System Operators (DSOs) has in many countries, partly as a consequence of the restructuring in ownership, gone through a major switch in regulatory policy. From applying regulatory regimes were the DSOs were allowed to charge their customers according to their actual cost plus some profit, i.e. cost-based regulation, to regulatory models in which the DSOs performance are valued in order to set the allowable revenue, i.e. Performance-Based Regulation (PBR). In regulatory regimes that value performance, the direct link between cost and income is weakened or sometimes removed. This give the regulated DSOs strong cost cutting incentives and there is consequently a risk of system reliability deterioration due to postponed maintenance and investments in order to save costs. To balance this risk the PBR-framework is normally complemented with some kind of quality regulation (QR). How both the PBR and QR frameworks are constructed determines the incentive that the DSO will act on and will therefore influence the system reliability development.</p><p>This thesis links the areas of distribution system reliability and performancebased regulation. First, the key incentive features within PBR, that includes the quality of supply, are identified using qualitative measures that involve analyses of applied regulatory regimes, and general regulatory policies. This results in a qualitative comparison of applied PBR models. Further, the qualitative results are quantified and analysed further using time sequential Monte Carlo simulations (MCS). The MCS enables detailed analysis of regulatory features, parameter settings and financial risk assessments. In addition, the applied PBRframeworks can be quantitatively compared. Finally, some focus have been put on the Swedish regulation and the tool developed for DSO regulation, the Network Performance Assessment Model (NPAM), what obstacles there might be and what consequences it might bring when in affect.</p>

No description available.

The objective of the proposed research is to quantify the limits of overstressed and aging circuit breakers in terms of probability of failure and to provide guidelines to determine network reconfigurations, generator commitment, and economic dispatch strategies that account for these limits. The proposed temporary power system operating strategies address circuit breaker adequacy issues and allow overstressed breakers to be operated longer and more reliably until they are replaced with adequate equipment. The expansion of electric networks with new power sources (nuclear plants, distributed generation) results in increased short-circuit or fault currents levels. As fault currents increase, they will eventually exceed circuit breaker ratings. Circuit breakers exposed to fault currents in excess of their ratings are said to be overstressed, underrated, or inadequate. Insufficient ratings expose overstressed breakers to increased failure probabilities. Extensive common-mode outages caused by circuit breaker failures reduce the reliability of power systems. To durably avoid outages and system unreliability, overstressed breakers must eventually be replaced. Large-scale replacements of overstressed breakers cannot be completed in a short time because of budgetary limits, capital improvement schedules, and manufacturer-imposed constraints. Meanwhile, to preserve the ability of old and overstressed breakers to safely interrupt faults, short-circuit currents must be kept within the limits imposed by the ratings and the age of these breakers by using the substation reconfiguration and generator commitment strategies described in this study. The immediate benefit of the above-mentioned operating strategies is a reduction of the failure probability of overstressed breakers obtained by avoiding the interruption of currents in excess of breaker ratings. Other benefits include (i) increased network reliability, (ii) restored operating margins with respect to existing equipment, and (iii) prioritized equipment upgrades that enhance the long-term planning of power systems.