In this study the incipient motion of coarse solitary particles on channel beds having different roughness heights was experimentally investigated. The experiments were conducted in a tilting flume of a rectangular cross-section having a working length of 12 m and a rough bed composed of at least 2 layers of coarse gravel of almost constant size. The roughness material of the channel bed was changed three times. The slope of the channel bed and the discharge are two main parameters that determine the initiation of motion of a given particle. The artificial particles tested in the experiments were obtained by mixing cement and iron dust at certain ratios. Dimensionless hydraulic parameters determined from theoretical analysis were related to each other. Flow depths, velocity profiles were measured and flow conditions that represent the critical conditions of initiation of motion were expressed in terms of critical velocities and shear velocities. The results were compared with the previous studies&rsquo / results.

Waterhammer is an unsteady hydraulic problem which is commonly found in closed conduits of hydropower plants, water distribution networks and liquid pipeline systems. Due to either a malfunction of the system or inadequate operation conditions, pipeline may collapse or burst erratically resulting in substantial damages, and human losses in some cases. In this thesis, time dependent flow situations in the penstocks of small hydropower plants are investigated. A software, HAMMER, that utilizes method of characteristics for solving nonlinear differential equations of transient flow is used in the study. In two case studies, various operation conditions such as load rejection, load acceptance and instant load rejection are studied. The parameters and situations affecting pressure and turbine speed rises are investigated. Computed and available measured values are found to be very close. Also, differences between waterhammer responses of the Francis and Pelton turbines are revealed. Finally, specific protective measures are suggested to either diminish and/or avoid the harmful effects of waterhammer problems in small hydropower plants.

In this study, piezometric heads in a composite aquifer composed of an alluvial deposit having a width adjacent to a semi-infinite fractured rock are determined. One dimensional transient flow induced by a constant discharge pumping rate from a stream intersecting alluvial part of the aquifer is considered. Parts of the aquifer are homogeneous andisotropic. Equations of flow, initial and boundary conditions are converted to dimensionless forms for graphical presentation and the interpretation of results independent of discharge and head inputs specific to the problem. Equations are solved first in Laplace domain and Laplace domain solutions are inverted numerically to real time domain by utilizing Stehfest algorithm.For this purpose, a set of subroutines in VBA Excel are developed. This procedure is verified by application of code to flow in semi-infinite homogeneous aquifer under constant discharge for which analytical solution is available in literature. VBA codes are also developed for two special cases of finite aquifer with impervious and with recharge boundary on the right hand side. Results of composite aquifer solutions with extreme tranmissivity values are compared with these two cases for verification of methodology and sensivity of results.

Orifices are essential devices for measurement and control of flow. It is important to define the flow field and understand the flow characteristics behind an orifice for the sake of reliability measures in many hydraulic engineering applications. Since analytical and experimental solutions are restricted, a numerical solution is obtained using volume of fluid (VOF) method with the CFD solver, FLUENT, for sharp crested orifices, orifice tubes and slots. The results are compared to the available data in the literature / also a large spectrum of data collection has been achieved.

Francis type turbines are commonly used in hydropower generation. Main components of the turbine are spiral case, stay vanes, guide vanes, turbine runner and the draft tube. The dimensions of these parts are dependent mainly on the design discharge, head and the speed of the rotor of the generators. In this study, a methodology is developed for parametric optimization by incorporating Matlab codes developed and commercial Computational Fluid Dynamics (CFD) codes into the design process. The design process starts with the selection of initial dimensions from experience curves, iterates to improve the overall hydraulic efficiency and obtain the detailed description of the final geometry for manufacturing with complete visualization of the computed flow field. A Francis turbine designed by the procedure developed has been manufactured and installed for energy production.

Excessive pumping in coastal aquifers results in seawater intrusion where optimal and efficient planning is essential. In this study, numerical solution of single potential solution by Strack is combined with genetic algorithm (GA) to find the maximum extraction amount in a coastal aquifer. Seawater intrusion is tracked with the potential value at the extraction well locations. A code is developed by combining GA and a subroutine repeatedly calling MODFLOW as a numerical solver to calculate the potential distribution for different configurations of solution (trial solutions). Potential distributions are used to evaluate the fitness values for GA. The developed model is applied to a previous work by Mantoglou. Another heuristic method, simulated annealing (SA) is utilized to compare the results of GA. Different seawater prevention methods (i.e. injection wells, canals) and decision variables related to those methods (i.e. location of the injection wells or canals) are added to model to further prevent the seawater intrusion and improve the coastal aquifer benefit. A method called &ldquo / Alternating Constraints Method&rdquo / is introduced to improve the solution for the cases with variable location. The results show that both proposed method and the regular solution with GA or SA prove to be successful methods for the optimal management of coastal aquifers.

All pipeline systems are susceptible to water hammer that can cripple critical infrastructure. One effective method to relieve excessive waterhammer pressures in pipelines is to use air chambers. This study aims to develop an empirical procedure for the quick analysis of penstock-turbine systems to determine dimensions and operating conditions of air-chambers that can effectively diminish the transient phenomena after sudden changes of flow rate in the system. A numerical study has been carried out by obtaining repeated solutions for variable system parameters using a commercial software. The relief brought by air chambers is found to approach to an asymptotic value for increasing chamber volumes. It is possible to determine the required chamber volume for a given discharge to limit the waterhammer pressures at a prescribed level in a given penstock-turbine system using the charts produced in the study.

Climate change concerns, high oil prices and increasing government support are some of the driving reasons of increasing renewable energy legislation, incentives, and commercialization. Hydroelectricity is the most widely used form of renewable energy and refers to electricity generated by hydropower. In this study, a storage facility is proposed to store some additional water and increase the profitability of the existing Birkapili Hydroelectric Power Plant. The storage facility is composed of a gravity dam and an uncontrolled spillway. With the help of the proposed storage facility, maximum utilization of the water is provided and shift of the electricity generation to peak demand periods becomes possible. Consequently, feasibility of the existing power plant is improved. A number of alternatives for a spillway are taken into account and the corresponding concrete gravity dam is designed. Stability analyses and operation studies are conducted using spreadsheets to achieve an economical solution.

Quality of municipal water is sustained by addition of disinfectant, generally chlorine, to the water distribution network. Because of health problems, chlorine concentration in the network is limited between maximum and minimum limits. Cancerogenic disinfectant by-products start to occur at high concentrations so it is desired to have minimum amount of chlorine without violating the limit. In addition to the health issues, minimum injection amount is favorable concerning cost. Hence, an optimization model is necessary which covers all of these considerations. However, there are uncertain factors as chlorine is reactive and decays both over time and space. Thus, probabilistic approach is necessary to obtain reliable and realistic results from the model. In this study, a linear programming model is developed for the chance constrained optimization of the water distribution network. The objective is to obtain minimum amount of injection mass subjected to maintaining more uniformly distributed chlorine concentrations within the limits while considering the randomness of chlorine concentration by probability distributions. Network hydraulics and chlorine concentration computations are done by the network simulation software, EPANET.

In practice, baffle blocks and sills are commonly being used to stabilize the location of a hydraulic jump and shorten the length of a stilling basin. On the other hand, gravels, corrugations and rectangular prismatic roughnesses which cover the entire length of the basin or placed in a staggered manner may be an alternative. The objective of this study is to determine the effects of these roughness elements on the characteristics of hydraulic jumps such as conjugate depth, jump length and energy dissipation using experimental data collected from the previous studies. The investigations show that the roughness elements have positive effects on the characteristics of hydraulic jumps. The tailwater depth reduction compared to classical jump is 2-10%. The length of the jump is reduced about by 30-50% by prismatic roughness elements, 40% by corrugations, and 30% by gravels. The roughness elements induce 3-15% more energy dissipation than that of classical jump. Therefore, these types of bed roughness elements should be considered as an effective alternative of accessory devices such as baffle blocks and sills.