The focus of this study was to investigate solutions that, when implemented in any heterogeneous wireless network, shall enhance the existing standard and routing protocol connectivity without impacting the standard or changing the wireless transceiver’s functions. Thus achieving efficient interoperability at much reduced overheads. The techniques proposed in this research are centred on the lower layers. This because of the facts that WiMax and WiFi standards have not addressed the backward compatibility of the two technologies at the MAC and PHY layers, for both the baseband functions as well as the routing IP addresses. This thesis describes two innovate techniques submitted for a PhD degree. The first technique is to combine WiMax and WiFi signals so to utilise the same "baseband implementation chain" to handle both of these technologies, thus insuring ubiquitous data communication. WiMax-WiFi Baseband Convergence (W2BC) implementation is proposed to offer an optimum configurable solution targeted at combining the 802.16d WiMax and the 802.11a WiFi technologies. This approach provides a fertile ground for future work into combining more OFDM based wireless technologies. Based on analysis and simulation, the W2BC can achieve saving in device cost, size, power consumption and implementation complexity when compared to current side-by-side implementations for these two technologies. The second technique, called "Prime-IP", can be implemented with, and enhance, any routing protocol. During the route discovery process, Prime-IP enables any node on a wireless mesh network (WMN) to dynamically select the best available route on the network. Prime-IP proposes a novel recursive process, based on prime numbers addressing, to accumulate knowledge for nodes beyond the “neighbouring nodes”, and to determine the sequence of all the “intermediate nodes” used to form the route

The recent research interest in wireless sensor networks has caused the development of many new applications and subsequently, these emerging applications have ever increasing requirements. One such requirement is that of mobility, which has inspired an entirely new array of applications in the form of mobile wireless sensor networks (MWSNs). In terms of communications, MWSNs present a challenging environment due to the high rate at which the topology may be changing. As such, the motivation of this work is to investigate potential communications solutions, in order to satisfy the performance demands of new and future MWSN applications. As such this work begins by characterising and evaluating the requirement of a large variety of these emerging applications. This thesis focuses on the area of routing, which is concerned with the reliable and timely delivery of data from multiple, mobile sensor nodes to a data sink. For this purpose the technique of gradient routing was identified as a suitable solution, since data can quickly be passed down a known gradient that is anchored at the sink. However, in a mobile network, keeping the gradient up-to-date is a key issue. This work proposes the novel use of a global time division multiple access (GTDMA) MAC as a solution to this problem, which mitigates the need for regularly flooding the network. Additionally, the concept of blind forwarding is utilised for its low overhead and high reliability through its inherent route diversity. The key contribution of this thesis is in three novel routing protocols, which use the aforementioned principles. The first protocol, PHASeR, uses a hop-count metric and encapsulates data from multiple nodes in its packets. The hop-count metric was chosen because it is simple and requires no additional hardware. The inclusion of encapsulation is intended to enable the protocol to cope with network congestion. The second protocol, LASeR, utilises location awareness to maintain a gradient and performs no encapsulation. Since many applications require location awareness, the communications systems may also take advantage of this readily available information and it can be used as a gradient metric. This protocol uses no encapsulation in order to reduce delay times. The third protocol, RASeR, uses the hop-count metric as a gradient and also does not perform encapsulation. The reduced delay time and the relaxed requirement for any existing method of location awareness makes this the most widely applicable of the three protocols. In addition to analytical expressions being derived, all three protocols are thoroughly tested through simulation. Results show the protocols to improve on the state-of-the-art and yield excellent performance over varying speeds, node numbers and data generation rates. LASeR shows the lowest overhead and delay, which comes from the advantage of having available location information. Alternatively, at the expense of increased overhead, RASeR gives comparatively high performance metrics without the need for location information. Overall, RASeR can be suitably deployed in the widest range of applications, which is taken further by including four additional modes of operation. These include a supersede mode for applications in which the timely delivery of the most recent data is prioritised. A reverse flooding mechanism, to enable the sink to broadcast control messages to the sensor nodes. An energy saving mode, which uses sleep cycles to reduce the networks power consumption, and finally a pseudo acknowledgement scheme to increase the reliability of the protocol. These additions enable RASeR to satisfy the needs of some of the most demanding MWSN applications. In order to assess the practicality of implementation, RASeR was also evaluated using a small testbed of mobile nodes. The successful results display the protocols feasibility to be implemented on commercially available hardware and its potential to be deployed in the real world. Furthermore, a key issue in the real world deployment of networks, is security and for this reason a fourth routing protocol was designed called RASeR-S. RASeR-S is based on RASeR, but introduces the use of encryption and suggests a security framework that should be followed in order to significantly reduce the possibility of a security threat. Whilst the main focus of this work is routing, alternative MAC layers are assessed for LASeR. Unlike the other two protocols, LASeR uses available location information to determine its gradient and as such, it is not reliant on the GTDMA MAC. For this reason several MAC layers are tested and the novel idea of dedicated sensing slots is introduced, as well as a network division multiple access scheme. The selected and proposed MACs are simulated and the GTDMA and two proposed protocols are shown to give the best results in certain scenarios. This work demonstrates the high levels of performance that can be achieved using gradient orientated routing in a mobile network. It has also shown that the use of a GTDMA MAC is an efficient solution to the gradient maintenance problem. The high impact of this work comes from the versatility and reliability of the presented routing protocols, which means they are able to meet the requirements of a large number of MWSN applications. Additionally, given the importance of security, RASeR-S has been designed to provide a secure and adaptable routing solution for vulnerable or sensitive applications.

While the bandwidth available for wireless networks is limited, the world has seen an unprecedented growth in the number of mobile subscribers and an ever increasing demand for high data rates. Therefore efficient utilisation of bandwidth to maximise link spectral efficiency and number of users that can be served simultaneously are primary goals in the design of wireless systems. To achieve these goals, in this thesis, a new non-orthogonal uplink multiple access scheme which combines the functionalities of adaptive modulation and multiple access called collaborative modulation multiple access (CMMA) is proposed. CMMA enables multiple users to access the network simultaneously and share the same bandwidth even when only a single receive antenna is available and in the presence of high channel correlation. Instead of competing for resources, users in CMMA share resources collaboratively by employing unique modulation sets (UMS) that differ in phase, power, and/or mapping structure. These UMS are designed to insure that the received signal formed from the superposition of all users' signals belongs to a composite QAM constellation (CC) with a rate equal to the sum rate of all users. The CC and its constituent UMSs are designed centrally at the BS to remove ambiguity, maximize the minimum Euclidian distance (dmin) of the CC and insure a minimum BER performance is maintained. Users collaboratively precode their transmitted signal by performing truncated channel inversion and phase rotation using channel state information (CSI ) obtained from a periodic common pilot to insure that their combined signal at the BS belongs to the CC known at the BS which in turn performs a simple joint maximum likelihood detection without the need for CSI. The coherent addition of users' power enables CMMA to achieve high link spectral efficiency at any time without extra power or bandwidth but on the expense of graceful degradation in BER performance. To improve the BER performance of CMMA while preserving its precoding and detection structure and without the need for pilot-aided channel estimation, a new selective diversity combining scheme called SC-CMMA is proposed. SC-CMMA optimises the overall group performance providing fairness and diversity gain for various users with different transmit powers and channel conditions by selecting a single antenna out of a group of L available antennas that minimises the total transmit power required for precoding at any one time. A detailed study of capacity and BER performance of CMMA and SC-CMMA is carried out under different level of channel correlations which shows that both offer high capacity gain and resilience to channel correlation. SC-CMMA capacity even increase with high channel correlation between users' channels. CMMA provides a practical solution for implementing the multiple access adder channel (MAAC) in fading environments hence a hybrid approach combining both collaborative coding and modulation referred to as H-CMMA is investigated. H-CMMA divides users into a number of subgroups where users within a subgroup are assigned the same modulation set and different multiple access codes. H-CMMA adjusts the dmin of the received CC by varying the number of subgroups which in turn varies the number of unique constellation points for the same number of users and average total power. Therefore H-CMMA can accommodate many users with different rates while flexibly managing the complexity, rate and BER performance depending on the SNR. Next a new scheme combining CMMA with opportunistic scheduling using only partial CSI at the receiver called CMMA-OS is proposed to combine both the power gain of CMMA and the multiuser diversity gain that arises from users' channel independence. To avoid the complexity and excessive feedback associated with the dynamic update of the CC, the BS takes into account the independence of users' channels in the design of the CC and its constituent UMSs but both remain unchanged thereafter. However UMS are no longer associated with users, instead channel gain's probability density function is divided into regions with identical probability and each UMS is associated with a specific region. This will simplify scheduling as users can initially chose their UMS based on their CSI and the BS will only need to resolve any collision when the channels of two or more users are located at the same region. Finally a high rate cooperative communication scheme, called cooperative modulation (CM) is proposed for cooperative multiuser systems. CM combines the reliability of the cooperative diversity with the high spectral efficiency and multiple access capabilities of CMMA. CM maintains low feedback and high spectral efficiency by restricting relaying to a single route with the best overall channel. Two possible variations of CM are proposed depending on whether CSI available only at the users or just at the BS and the selected relay. The first is referred to Precode, Amplify, and Forward (PAF) while the second one is called Decode, Remap, and Forward (DMF). A new route selection algorithm for DMF based on maximising dmin of random CC is also proposed using a novel fast low-complexity multi-stage sphere based algorithm to calculate the dmin at the relay of random CC that is used for both relay selection and detection.

The idea of the smart home has been discussed for over three decades, but it has yet to achieve mass-market adoption. This thesis asks the question Why is my home not smart? It highlights four main areas that are barriers to adoption, and concentrates on a single one of these issues: usability. It presents an investigation that focuses on design, prototyping and evaluation of mobile interfaces for domestic environments resulting in the development of a novel framework. A smart home is the physical realisation of a ubiquitous computing system for domestic living. The research area offers numerous benefits to end-users such as convenience, assistive living, energy saving and improved security and safety. However, these benefits have yet to become accessible due to a lack of usable smart home control interfaces. This issue is considered a key reason for lack of adoption and is the focus for this thesis. Within this thesis, a framework is introduced as a novel approach for the design, prototyping and evaluation of mobile interfaces for domestic environments. Included within this framework are three components. Firstly, the Reconfigurable Multimedia Environment (RME), a physical evaluation and observation space for conducting user centred research. Secondly, Simulated Interactive Devices (SID), a video-based development and control tool for simulating interactive devices commonly found within a smart home. Thirdly, iProto, a tool that facilitates the production and rapid deployment of high fidelity prototypes for mobile touch screen devices. This framework is evaluated as a round-tripping toolchain for prototyping smart home control and found to be an efficient process for facilitating the design and evaluation of such interfaces.

With the expectation of over a 1000-fold increase in the number of connected devices by 2020, efficient utilization of the limited bandwidth has become ever more important in the design of mobile wireless systems. Furthermore, the ever-increasing demand for higher data rates has made it necessary for a new waveform design that satisfies not only throughput demands, but network capacity as well. One such technique recently proposed is the non-orthogonal multiple access (NOMA) which utilizes the distance-dependent power domain multiplexing, based on the principles of signal superposition. In this thesis, new spectrally efficient non-orthogonal signal techniques are proposed. The goal of the schemes is to allow simultaneous utilization of the same time frequency network resources. This is achieved by designing component signals in both power and phase domain such that users are precoded or preformed to form a single and uniquely decodable composite signal. The design criteria are based on maximizing either the sum rate or spectral efficiency, minimizing multi-user interference and detection ambiguity, and maximizing the minimum Euclidean distance between the composite constellation points. The design principles are applied in uplink, downlink and coordinated multipoint (CoMP) scenarios. We assume ideal channel state with perfect estimation, low mobility and synchronization scenarios so as to prove the concept and serve as a bound for any future work in non-ideal conditions. Extensive simulations and numerical analysis are carried to show the superiority and compatibility of the schemes. First, a new NOMA signal design called uplink NOMA with constellation precoding is proposed. The precoding weights are generated at the eNB based on the number of users to be superposed. The eNB signals the precoding weights to be employed by the users to adjust their transmission. The adjustments utilize the channel state information estimated from common periodic pilots broadcasted by the eNB. The weights ensure the composite received signal at the eNB belongs to the pre-known constellation. Furthermore, the users precode to the eNB antenna that requires the least total transmit power from all the users. At the eNB, joint maximum likelihood (JML) detection is employed to recover the component signals. As the composite constellation is as that of a single user transmitting that same constellation, multiple access interference can be viewed as absent, which allows multiple users to transmit at their full rates. Furthermore, the power gain achieved by the sum of the component signals maximizes the sum rate. Secondly, the constellation design principle is employed in the downlink scenario. In the scheme, called downlink NOMA with constellation preforming, the eNB preforms the users signal with power and phase weights prior to transmission. The preforming ensures multi-user interference is eliminated and the spectral efficiency maximized. The preformed composite constellation is broadcasted by the eNB which is received by all users. Subsequently, the users perform JML detection with the designed constellation to extract their individual component signals. Furthermore, improved signal reliability is achieved in transmit and receive diversity scenarios in the schemes called distributed transmit and receive diversity combining, respectively. Thirdly, the constellation preforming on the downlink is extended to MIMO spatial multiplexing scenarios. The first MIMO scheme, called downlink NOMA with constellation preforming, each eNB antenna transmits a preformed composite signal composed of a set of multiple users' streams. This achieves spatial multiplexing with diversity with less transmit antennas, reducing costs associated with multiple RF chains, while still maximizing the sum rate. In the second MIMO scheme, a highly spectrally efficient MIMO preforming scheme is proposed. The scheme, called group layer MIMO with constellation preforming, the eNB preforms to a specific group of users on each transmit antenna. In all the schemes, the users perform JML detection to recover their signals. Finally, the adaptability of the constellation design is shown in CoMP. The scheme, called CoMP with joint constellation processing, the additional degrees of freedom, in form of interfering eNBs, are utilized to enable spatial multiplexing to a user with a single receive antenna. This is achieved by precoding each stream from the coordinating eNB with weights signalled by a central eNB. Consequently, the inter-cell interference is eliminated and the sum-rate maximized. To reduce the total power spent on precoding, an active cell selection scheme is proposed where the precoding is employed on the highest interferers to the user. Furthermore, a power control scheme is applied the design principle, where the objective is to reduce cross-layer interference by adapting the transmission power to the mean channel gain.

The research contributes to work in Rapid Deployment of a National Public Security and Emergency Communications Network using Communication Satellite Broadband. Although studies in Public Security Communication networks have examined the use of communications satellite as an integral part of the Communication Infrastructure, there has not been an in-depth design analysis of an optimized regional broadband-based communication satellite in relation to the envisaged service coverage area, with little or no terrestrial last-mile telecommunications infrastructure for delivery of satellite solutions, applications and services. As such, the research provides a case study of a Nigerian Public Safety Security Communications Pilot project deployed in regions of the African continent with inadequate terrestrial last mile infrastructure and thus requiring a robust regional Communications Satellite complemented with variants of terrestrial wireless technologies to bridge the digital hiatus as a short and medium term measure apart from other strategic needs. The research not only addresses the pivotal role of a secured integrated communications Public safety network for security agencies and emergency service organizations with its potential to foster efficient information symmetry amongst their operations including during emergency and crisis management in a timely manner but demonstrates a working model of how analogue spectrum meant for Push-to-Talk (PTT) services can be re-farmed and digitalized as a “dedicated” broadband-based public communications system. The network's sustainability can be secured by using excess capacity for the strategic commercial telecommunication needs of the state and its citizens. Utilization of scarce spectrum has been deployed for Nigeria's Cashless policy pilot project for financial and digital inclusion. This effectively drives the universal access goals, without exclusivity, in a continent, which still remains the least wired in the world.

With the proliferation of smartphones and their advanced connectivity capabilities, opportunistic networks have gained a lot of traction during the past years; they are suitable for increasing network capacity and sharing ephemeral, localised content. They can also offload traffic from cellular networks to device-to-device ones, when cellular networks are heavily stressed. Opportunistic networks can play a crucial role in communication scenarios where the network infrastructure is inaccessible due to natural disasters, large scale terrorist attacks or government censorship. Geocasting, where messages are destined to specific locations (casts) instead of explicitly identified devices, has a large potential in real world opportunistic networks, however it has attracted little attention in the context of opportunistic networking. In this thesis, we propose Geocasting Spray And Flood (GSAF), a simple but efficient and flexible geocasting protocol for opportunistic, delay tolerant networks. GSAF follows a simple but elegant and flexible approach where messages take random walks towards the destination cast. Messages that follow directions away from the cast are extinct when the device buffer gets full, freeing space for new messages to be delivered. In GSAF, casts do not have to be pre-defined; instead users can route messages to arbitrarily defined casts. Also, the addressed cast is flexible in comparison to other approaches and can take complex shapes in the network. DA-GSAF as the direction aware version of the GSAF is proposed as well which use location information to aid routing decisions in the GSAF. Extensive evaluation shows that GSAF and DA-GSAF are significantly more efficient than existing solutions, in terms of message delivery ratio and latency as well as network overhead.