Electrospinning is a method of producing nano structured material from a polymer solution or melt using high strength electric fields. It is a process that has yet to find extensive industrial application yet shows promise if obstacles such as low rate of production overcome perhaps by more complete theoretical modelling. This work examines the effects of adding an ionic salt to a solution of poly(vinyl alcohol) in water. The direct effect was an increase the charge density and electric current. It was found that an increase in charge density decreases the mass deposition rate and forms a thinner initial jet. When the sign of the charge on the polymer solution was changed from positive to negative the charge density increased and the initial jet diameter and mass deposition rate also decreased. It was proposed that a smaller radius of curvature is formed by the Taylor cone at higher charge densities resulting in a smaller “virtual orifice”. The extent of the bending instability was explored and it was found that adding ionic salt results in a decrease in the bending instability resulting in thicker fibres. Changing the sign of the charge on the polymer solution from positive to negative resulted in an increase in the bending instability and resulted in thinner fibres. The charge transfer mechanisms used in different electrospinning models are explored and some assumptions not explicitly stated are discussed. From this discussion a generalized equation describing the charge transport mechanisms is proposed.

A new approach for the control of the size of particles fabricated using the Electrohydrodynamic Atomization (EHDA) method is being developed. In short, the EHDA process produces solution droplets in a controlled manner, and as the solvent evaporates from the surface of the droplets, polymeric particles are formed. By varying the voltage applied, the size of the droplets can be changed, and consequently, the size of the particles can also be controlled. By using both a nozzle electrode and a ring electrode placed axisymmetrically and slightly above the nozzle electrode, we are able to produce a Single Taylor Cone Single Jet for a wide range of voltages, contrary to just using a single nozzle electrode where the range of permissible voltage for the creation of the Single Taylor Cone Single Jet is usually very small. Phase Doppler Particle Analyzer (PDPA) test results have shown that the droplet size increases with increasing voltage applied. This trend is predicted by the electrohydrodynamic theory of the Single Taylor Cone Single Jet based on a perfect dielectric fluid model. Particles fabricated using different voltages do not show much change in the particles size, and this may be attributed to the solvent evaporation process. Nevertheless, these preliminary results do show that this method has the potential of providing us with a way of fine controlling the particles size using relatively simple method with trends predictable by existing theories. / Singapore-MIT Alliance (SMA)

Electrospinning is a method of producing nano structured material from a polymer solution or melt using high strength electric fields. It is a process that has yet to find extensive industrial application yet shows promise if obstacles such as low rate of production overcome perhaps by more complete theoretical modelling. This work examines the effects of adding an ionic salt to a solution of poly(vinyl alcohol) in water. The direct effect was an increase the charge density and electric current. It was found that an increase in charge density decreases the mass deposition rate and forms a thinner initial jet. When the sign of the charge on the polymer solution was changed from positive to negative the charge density increased and the initial jet diameter and mass deposition rate also decreased. It was proposed that a smaller radius of curvature is formed by the Taylor cone at higher charge densities resulting in a smaller “virtual orifice”. The extent of the bending instability was explored and it was found that adding ionic salt results in a decrease in the bending instability resulting in thicker fibres. Changing the sign of the charge on the polymer solution from positive to negative resulted in an increase in the bending instability and resulted in thinner fibres. The charge transfer mechanisms used in different electrospinning models are explored and some assumptions not explicitly stated are discussed. From this discussion a generalized equation describing the charge transport mechanisms is proposed.

Electrospininig se osvědčil jako jeden z nejpopulárnějších a nejrozšířenějších způsobů výroby vysoce kvalitních vláken s požadovanými parametry. Kvalita a morfologie vyráběných vláken závisí na mnoha parametrů, jako je vlhkost, dávka materiálu, aplikované napětí atd. Omezení keramických piezomateriálů (křehkost, toxicita vzorků obsahujících olovo, obtížnost přípravy složitých tvarů atd.) vynutila výzkum v oblasti piezoelektrických polymerů. Jedním z nich je polyvinylidenfluorid (PVDF). polyvinylidenfluorid může by být připraven v různých formách: tenké filmy, objemové vzorky, vlákna. PVDF vlákna přitahují největší pozornost díky vysoké flexibilitě, nízké hmotnosti, mechanické stabilitě a chemické inertnosti. Vlastnosti PVDF vláken lze zlepšit pomocí doplňujících materiálů: keramické částice, kovové nanočástice, Graphicitové materiály jako jsou oxid Graphicenu nebo uhlíkové nanotrubičky (CNT).

No description available.