In a fiber spinning process molten polymer is extruded into a fiber. The resulting fiber known as as-spun fiber is relatively weak and shows a large plastic central zone in its constitutive behavior. As a result the fiber deforms substantially without a significant change in load thus making it unsuitable for stress bearing applications. The range of plastic deformation is related to the natural draw ratio. In order to improve the mechanical properties of as spun fibers, fiber spinning is followed by a fiber draw process. With multi stage draw the as-spun fiber is drawn beyond the plastic region in various drawing zones which produces greater orientation of the polymer chains in the axial direction of the fiber thus enhancing mechanical strength characteristics of the fiber. The multistage draw process consists of several rollers each rotating at a speed greater than the one prior to it. The objective of this work is to develop a first approximation to model fiber draw in the multistage drawing process, with and without a draw pin. As the first step the slippage of fibers on rollers was analysed by including centrifugal acceleration and acceleration due to stretching. The draw in a free span is also modelled. Several representative draw processes were examined. It was found draw pin localizes the draw significantly although the resulting mechanical unloading complicates the analysis. Draw in the free span is impossible for isothermal draw processes, and anisothermal draw induces thermal unloading in the system. A comprehensive analysis of various draw processes will be examined.

Particles originating from bacteria, fungi (including mold spores, mildew, yeast), pollen, dust mites, and viruses can induce immune responses that trigger allergies and asthma. Carpeting is believed to act as a "sink" where bioparticulates are trapped via adhesive interactions and then are released by foot traffic or cleaning. This scenario can result in an accumulation of contaminants at higher levels than would be found outdoors or in a carpet-less environment. Numerous organizations (school districts, hospitals) have taken steps to remove carpeting, even though this hypothesis remains unproven. While statistical studies exist both in support and denial of the accumulation hypothesis, there is little fundamental understanding of the microscopic-level interactions between carpet and bioparticles. A fundamental understanding of particle affinities with polymers utilized in carpet would help to develop accurate models and address real problems in a rational and productive manner. In addition, a solution to the bioparticulate accumulation problem would have a profound impact on US health, resulting in significant economic savings. More than 20 million people suffer from asthma in the U.S., with children being the most vulnerable. In 2000 there were 9.3 million physician office visits and 1.8 million emergency room visits due to asthma alone, resulting in an estimated $9.4 billion in medical costs and $4.6 billion in lost productivity annually. In this thesis, two measurement techniques were developed to quantify the adhesive interactions between biological particulates and polymeric carpeting materials. Atomic force microscopy (AFM) was used to measure the adhesive interactions of relevant biological particulates (in this case the E. coli bacteria and A. artemisiifolia ragweed pollen grains) with Nylon-6 and Nylon-6,6, polyamide-12 and polystyrene. The adhesion force measurements were modeled using several adhesion theories. We found that the Hamaker models were sufficient for explaining the data, indicating the prominence of van der Waals forces in controlling bioparticle interactions with polyamides. In addition, the geometry of the pollen played a significant role: adhesion forces were approximately a multiple of the number of contact points the grain has with the surface. Forces for E. coli and polyamides were about the same magnitude as polyamide-polyamide surface self-interactions.

M. Tech. (Department of Chemical Engineering, Faculty of Engineering and Technology), Vaal University of Technology / Fenton oxidation is classified into two processes, homogeneous and heterogeneous. Homogeneous Fenton oxidation process, have been shown to be efficient in the degradation of organic pollutants. However, it was shown to have limitations which can be addressed by the heterogeneous Fenton oxidation. Despite the high efficiency of the heterogeneous Fenton oxidation process in the degradation of recalcitrant organic pollutants, the currents synthesis trends of the heterogeneous Fenton catalyst have been proven to be time and energy constraining, since it involves the multi-step were the activated carbon have to be prepared first then co-precipitate the iron oxide on the activated carbon. However, as much as the heterogeneous Fenton catalyst has been proven to have high catalytic activity towards degradation of organic pollutants, these catalysts have some limitations, such limitations include metal ions being leached from the catalyst support into the treated water causing catalyst deactivation and a secondary pollution to the treated water. In this thesis, these catalysts have been applied in the degradation of recalcitrant organic pollutants such as methylene blue and phenols. This study focuses on the single step synthesis of iron oxide nanoparticles supported on activated carbon, were carbonaceous material is impregnated with iron salt then pyrolysed via microwave heating. Microwave power and the amount of iron salt were optimized. The prepared activated carbon-iron oxide composites were applied to the degradation of 2-nitrophenol (2-NP) and methylene blue (MB). Methylene blue was used as a model compound due to the fact that it is easier to monitor the degradation process with UV-Vis as compared to 2-nitrophenol . 2-nitrophenol the additional step for the adjustment of pH is required since nitrophenols are colorless in color at lower pH. The characterization showed that the microwave power and the amount of the iron precursor have an influence on the porosity and surface functional groups of the activated carbon. Further it was vi observed that microwave power and iron precursor influnces the amount of iron oxide formed on the surface of the support. It was also observed that the activated carbon-iron oxide composite have the catalytic effects on the Fenton oxidation process of MB and 2-NP. The parameters such as H2O2, pH, catalyst dose, initial concentration, temperature affect the degradation of both MB and 2-NP. Kinetics studies showed that Fenton is a surface driven reaction since the results fitted the pseudo first order model. The thermodynamics parameters also showed that the reaction is endothermic, spontaneous and is randomized. This implies that the reaction of the degradation of MB and 2-NP is feasible and the catalysts prepared have high catalytic activity. MB and 2-NP were degraded to smaller organic molecules (carboxylic acids). The stability of the catalyst observed to decrease as the number of cycles increased, this is due to the leaching of iron ions from the support material. Hence it was concluded that the activated carbon-iron oxide composite was successfully synthesized and had the high catalytic activity for the degradation of MB and 2-NP.

PhD (Department of Chemistry, Faculty of Applied and Computer Sciences), Vaal University of Technology. / Water is a basic resource to mankind. The environment is deteriorating daily due to industrial pollution of water resources. Industrial effluents containing organic pollutants such as dyes are undesirable even at low concentrations in the environment. Natural biomaterials have been applied as adsorbents for dye removal from water systems, however, their application has been limited by their low adsorption capacity. Much attention has been focused on the chemical modification of natural biomass via grafting processes. The modification of natural polymers by graft copolymerization is a promising technique since it functionalizes a biopolymer thus imparting desirable properties. The purpose of the study was to prepare and optimize the working conditions for the pine-magnetite bionanocomposites (PMC) as adsorbents and as photocatalysts modifiers. First, this work focuses on the synthesis and optimization of reaction variables in the preparation of PMC for the removal of methylene blue (MB). The thesis also explores the synthesis of acrylamide and acrylic acid-grafted PMC, resulting in the formation of acrylamide-grafted PMC (GACA) and acrylic acid-grafted pine-magnetite bionanocomposites (GAA), respectively. The grafting of functional groups such as –CO, –NH2 onto cellulose from acrylamides is also explored in detail. The adsorption conditions optimized were used to investigate the adsorption efficiency of GAA and GACA on MB. Finally, the application of PMC and GAA as modifiers for amorphous TiO2 and N-doped TiO2was carried out. The photocatalytic bionanocomposites from PMC (namely PMC–a-C,TiO2 and PMC–a-C,NTiO2) and those from GAA (labeled GAA–a-C,TiO2 and GAA–a-C,NTiO2) are compared by their photocatalytic efficiency on the degradative removal of an alkaline dye mixture formed from Reactive red 120 (RR 120) and Rhodamine B (Rh B). The synthesis procedure for PMC involved treating pinecone biomass with 0.15 M NaOH solution to remove unwanted plant extracts and the subsequent coating of the treated pinecone with iron oxide magnetic particles through a co-precipitation method. The variables used for the experiments were volume of NH4OH (5 to 40 cm3), reaction temperature (40 to 100 °C), effect of time (15 to 60 min) and mass (1.0 to 3.5 g). The PMC and acrylic acid grafted pine-magnetite composite (GAA) were probed for structural morphology and surface properties using various surface characterization instrumental techniques. Strong chemical interactions between pinecone magnetite and acrylic acid were demonstrated by thermogravimetric (TGA), differential thermal analysis (DTA) and X-ray photoelectron spectroscopy (XPS) for these unique bionanocomposites as such suggesting high chemical stability. Grafting acrylic acid was shown by XPS to form polyacrylic acid on the surface of the bionanocomposites and thus capping the surface groups. Significant differences in size were shown by transmission electron spectroscopy (TEM) and scanning electron microscopy (SEM); i.e., smaller particle sizes (Ave = 13.0 nm) for GAA and slightly larger for PMC (Ave = 14.0 nm). Brunauer Emmett Teller (BET) surface analysis demonstrated a larger surface area, pore volume and pore diameter (59.9 m2.g-1, 0.2254 cm3.g-1 and 28.14) for GAA compared to PMC. These characteristics coupled with the point of zero charge for GAA (pHpzc = 6.8) were critical in enhancing the efficiency of GAA adsorption of MB at pH 12 and further enable GAA to have a higher desorption efficiency of up to 99.7% after four cycles of washing with 0.10 M HCl. The adsorption kinetics and isotherm studies indicated that the adsorption process follows the pseudo second order kinetics and Langmuir isotherm respectively. The adsorbent also showed improvement in the adsorption capacity and reusability promising to be used for the removal of dyes in a prototype scale. GAA and MB adsorption mechanism was confirmed to be through intra particle diffusion. The overall performance of the GAA bionanocomposites is hinged on the formation of polyacrylic acid on the surface, its structural morphology, and the enhanced surface properties. Most importantly, the plant-based materials (lignin and cellulose) provide an environment that is rich with surface (–COOH and –OH) groups for the attachment of the magnetite nanoparticles while the polyacrylic acid stabilizes the magnetite onto the pinecone nanoparticles while reducing the point of zero charge for increased adsorption of cationic species. The photocatalytic bionanocomposites were fabricated from the adsorptive bionanocomposites using a simple solgel process in which ~10 wt.% of PMC and GAA, respectively, were used as a starting agent. Titanium butoxide was used as a precursor, acetylacetone as a dispersant and ethylene diamine as a nitrogen source. Using this procedure, amorphous carbon-doped titania (a-C,TiO2) and amorphous carbon and nitrogen co-doped titania (a-C,NTiO2) were fabricated except that the biopolymer was not added. Two sets of amorphous titania bionanocomposites were fabricated. One set was the nitrogen doped forms that had been modified with PMC and GAA (PMC–a-C,TiO2 and GAA–a-C,NTiO2). The other set of photocatalytic bionanocomposites produced in this work were without nitrogen (PMC–a-C,TiO2 and GAA–a-C,TiO2). TEM and SEM micrographs showed that all the photocatalysts consisted of globular, smooth aggregates of nanosized a-CTiO2 and a-C,NTiO2 which decreased in size with N-doping and the incorporation of GAA and PMC to as low as <30 nm. Surface chemical analysis through FTIR, XPS and EDS confirmed the presence of C, O, Ti and N (for the N-doped photocatalysts). In addition, it was demonstrated that N-doping into TiO2 had taken place, albeit with most of the N incorporated as organic nitrogen. It was further demonstrated that because of the absence of high temperature calcination, the process chemicals played a significant role in doping the photocatalysts with carbon resulting in the promotion of photocatalytic activity for a-C,TiO2 to the point of surpassing that of, a-C,NTiO2 and all the PMC-modified photocatalytic bionanocomposites. a-C,TiO2 had an overall 94% removal of the dyes, Rhodamine B (RhB) and Reactive red 120(RR 120), under UV illumination. The benefit of co-doping a-TiO2 with C, N and the biopolymers was realized with the incorporation of GAA as a modifier. The result was 97% removal of the dyes by GAA–a-CTiO2 and 99% for GAA–a-C,NTiO2. It was further observed that the degradation of the binary mixture of the dyes (RhB and RR 120) proceeded through the zero order kinetics for the a-C,TiO2 based photocatalysts and first order kinetics for the N-doped photocatalysts. The work, has, therefore demonstrated the applicability of plant-based biopolymers in the fabrication of nanoadsorbents and nanophotocatalysts. While the photocatalytic degradations were carried out under UV-light, there still remains a number of possible avenues that researchers can build on to improve the visible light-driven photocatalytic bionanocomposites. The research work has proven the effectiveness of novel pinecone magnetic nanoparticle materials and TiO2-based photocatalyst for the degradation of undesirable dyes from wastewater.