Thesis (M.S.)--University of Wisconsin--Madison, 1969. / eContent provider-neutral record in process. Description based on print version record. Includes bibliographical references.

Thesis (M.S.)--University of Wisconsin--Madison. / Typescript. eContent provider-neutral record in process. Description based on print version record. Includes bibliographical references (leaves 125-127).

Thesis (M.S.)--Carnegie-Mellon University, 1981. / Includes bibliographical references (p. 44).

Thesis (Ed.M.)--Boston University

No description available.

In recent years there has been increased interest in the development of sensorless switched reluctance machine drives. The proper operation of a switched reluctance machine (SRM) requires knowledge of the position of the rotor of the machine. The inclusion of a physical position sensor compromises the inherent robustness of this type of machine. Thus, there has been a need to develop techniques to estimate the position of the rotor in SRM drives. Switched reluctance machines are able to operate over a large range in speed. A fully loaded SRM is typically designed to saturate the ferromagnetic material that comprises the stator and rotor of the machine whereas a lightly loaded machine does not. Therefore, the model of the machine should be able to handle both a large range in frequency and input excitation levels of the magnetic material in the machine. The development of a new dynamic circuit-based ferromagnetic model is described in this thesis. The investigation of the behaviour of 24 gauge M19 silicon steel led to the conclusion that, for this material, a circuit model that has static parameters is unable to accurately reproduce the behaviour of the actual material over a large range of input frequencies and excitation levels without resorting to retuning the parameters of the model. This thesis provides two new mechanisms that dynamically adjust the resistance values of the flux tubes of the model. Comparisons using a normalized vertical least-squares metric between the newly proposed dynamic model and a model that has static resistance values clearly show the improvement that is gained by using these mechanisms. A practical implementation of the new model is also given. Timing using a general purpose CPU shows that this implementation of the model will most likely be able to be used as part of a multi-phase lumped parameter model for a SRM in realtime. / Applied Science, Faculty of / Electrical and Computer Engineering, Department of / Graduate

State-of-the-art multi-processor systems-on-chip use on-chip networks as their communication fabric. Although most on-chip networks are implemented synchronously, asynchronous on-chip networks have several advantages over their synchronous counterparts. Timing division multiplexing (TDM) flow control methods have been utilized in asynchronous on-chip networks extensively. The synchronization required by TDM leads to significant speed penalties. Compared with using TDM methods, spatial parallelism methods, such as the spatial division multiplexing (SDM) flow control method, achieve better network throughput with less area overhead.This thesis proposes several techniques to increase spatial parallelism in the routers of asynchronous on-chip networks.Channel slicing is a new pipeline structure that alleviates the speed penalty by removing the synchronization among bit-level data pipelines. It is also found out that the lookahead pipeline using early evaluated acknowledgement can be used in routers to further improve speed.SDM is a new flow control method proposed for asynchronous on-chip networks. It improves network throughput without introducing synchronization among buffers of different frames, which is required by TDM methods. It is also found that the area overhead of SDM is smaller than the virtual channel (VC) flow control method -- the most used TDM method. The major design problem of SDM is the area consuming crossbars. A novel 2-stage Clos switch structure is proposed to replace the crossbar in SDM routers, which significantly reduces the area overhead. This Clos switch is dynamically reconfigured by a new asynchronous Clos scheduler.Several asynchronous SDM routers are implemented using these new techniques. An asynchronous VC router is also reproduced for comparison. Performance analyses show that the SDM routers outperform the VC router in throughput, area overhead and energy efficiency.

This thesis deals with the creation of visualization for control, display and record data from the hydraulic circuit, which is used for testing water heaters. Visualization is created in the program Control Web from Moravian Instruments. Hydraulic circuit is located in the Strojírenský zkušebný ústav, s.p.. Visualization contribute to automating experiments. Technological unit is controlled by the programmable controller, which communicates via the OPC server with the user interface on PC.

Most mineral and coal processing plants are forced to size their particulate streams in order to maximize the efficiency of their unit operations. Classifiers are generally considered to be more practical than screens for fine sizing, but the separation efficiency decreases dramatically for particles smaller than approximately 150 μm. In addition, classifiers commonly suffer from bypass, which occurs when a portion of the ultrafine particles (slimes) are misplaced by hydraulic carryover into the oversize product. The unwanted misplacement can have a large adverse impact on downstream separation processes. One method of reducing bypass is to inject water into the cyclone apex. Unfortunately, existing water injection systems tend to substantially increase the particle cut size, which makes it unacceptable for ultrafine sizing applications. A new apex washing technology was developed to reduce the bypass of ultrafine material to the hydrocyclone underflow while maintaining particle size cuts in the 25-50 m size range. Another method of reducing bypass is to retreat the cyclone underflow using multiple stages of classifiers. However, natural variations in the physical properties of the feed make it difficult to calculate the exact improvement offered by multistage classification in experimental studies. Therefore, several mathematical equations for multistage classification circuits were evaluated using mathematical tools to calculate the expected impact of multistage hydrocyclone circuits on overall cut size, separation efficiency and bypass. These studies suggest that a two-stage circuit which retreats primary underflow and recycles secondary overflow offers the best balance between reducing bypass and maintaining a small cut size and high efficiency. / Master of Science

<p> Two ways of measuring the relative phase in microwave fields are described in the second chapter of this thesis. The homodyne circuit is described in detail as this method was the one eventually used because of its high accuracy. Measurements were taken using a one inch dielectric rod and these were compared with theoretical predictions as calculated by previous and present laboratory workers here. Conclusions and suggestions for further work are presented in the last chapter.</p> / Thesis / Master of Science (MSc)