Mobile communications have developed since the radio communications that were in use 50 years ago. With the advent of GSM, mobile communications was brought to the average citizen. More recently, COMA technology has provided the user with higher data rates and more reliable service, and it is apparent that it is the future of wireless communication. With the introduction of 3G technology in South Africa, it is becoming clear that it is the solution to the country's wireless communication requirements. The 3G and next-generation technologies could provide reliable communications to areas where it has proven difficult to operate and maintain communications effectively, such as rural locations. It is therefore important that the se technologies continue to be researched in order to enhance their capabilities to provide a solution to the wireless needs of the local and global community. Whilst COMA is proving to be a reliable communications technology, it is still susceptible to the effects of the near-far problem and multiple-access interference. A number of multiuser detectors have been proposed in literature that attempt to mitigate the effects of multiple-access interference. A notable detector is the blind MOE detector, which requires only the desired user 's spreading sequence , and it exhibits performance approximating that of other linear multiuser detectors. Another promising class of multiuser detector operate using an iterative principle and have a joint multiuser detection and error-correcting coding scheme. The aim of this research is to develop a blind iterative detector with FEC coding as a potential solution to the need for a detector that can mitigate the effects of interfering users operating on the channel. The proposed detector has the benefits of both the blind and iterative schemes: it only requires the knowledge of the desired user ' s signature, and it has integrated error-correcting abilities. The simulation results presented in this dissertation show that the proposed detector exhibits superior performance over the blind MOE detector for various channel conditions. An overview of spread-spectrum technologies is presented, and the operation of OS-COMA is described in more detail. A history and overview of existing COMA standards is also given . The need for multiuser detection is explained, and a description and comparison of various detection methods that have appeared in literature is given. An introduction to error coding is given , with convolutional code s, the turbo coding concept and method s of iterative detection are described in more detail and compared, as iterat ive decoding is fundamental to the operation of an iterative COMA detector. An overview of iterative multiuser detection is given , and selected iterative methods are described in more detail. A blind iterative detector is proposed and analysed. Simulation results for the propo sed detector, and a comparison to the blind MOE detector is presented, showing performance characteristics and the effects of various channel parameters on performance. From these results it can be seen that the proposed detector exhibits a superior performance compared to that of the blind MOE detector for various channel conditions. The dissertation is concluded, and possible future directions of research are given. / Thesis (M.Sc.Eng.)-University of KwaZulu-Natal, Durban, 2005.

Current melt texturing processes can only produce high-quality High Temperature Superconducting (HTSC) domains of a few centimetres in size. Increasing the size of the domain by a joining technique is investigated. The parent HTSC melt textured domains of YBa2CU307-li (Y 123), were used in this research to investigate the joining technique. The solder powders used to form the seam were HTSC YbBa2Cu307-li (YbI23), which has a peritectic temperature of approximately 925 cC, Yb2BatCu\07_o (Yb211), Silver Oxide (Ag20) and Y123. A total of 8 different superconducting 'solders' were manufactured using these powders. Microstructural analyses using a scanning electron microscope (SEM) and an optical microscope were conducted on each sample. It was found that mechanisms occurring during the growth of the seam affect the performance of the join. During the growth, three interfaces are formed. The interface between the parent and the growth front produced an excellent join whereas most of the microstructural defects were present at the intersection of the two growth fronts also known as the impingement boundary. The effect of the addition of Yb211 and silver particles to the join were investigated. It was found that although Yb211 particles improve the flux pinning and viscosity of the solder and the silver improves the intergranular critical current density (Jc) [1], they also reduce the effective cross-sectional area of the joined sample. Thus, the amount of non-superconducting particles added needs to be optimised. Transport measurements were taken to evaluate the current carrying capacity of each sample. It was found that Sample 2-A (Yb123 + 5%Ag20) has the highest Jc of approximately 142 A/cm 2 at 80 K while Sample 3-A (Y123 + 5%Ag20) has the poorest Jc of about 37 A/cm2 at 80 K. Resistivity vs. Temperature graphs show that all joined samples were superconducting implying that the joining process was successful in establishing a superconducting join. Magnetic field maps of the parent and joined samples were captured using a Hall Probe. It was found that the joined sample could trap almost 95 % of the field that could be trapped by the parent. From these results, it was concluded that joining HTSC bulk pieces is possible using an external 'soldering' agent. / Thesis (M.Sc.Eng.)-University of KwaZulu-Natal, Durban, 2005.

The contemporary approach to change in Nedbank is focused on mechanistic processes with little reference to social systems that exist in organisations. The contemporary approach assumes that an organisation is linear in nature and as such, a reductionist approach is employed for organisational inquiry to address organisational structure, strategy and culture. This research will focus on employing a systems approach to organisational inquiry to elicit themes that leadership should be aware of, to effect change in a dynamic and complex environment. The argument presented is that organisations are about people that interrelate with each other to achieve organisational goals, and as such exhibit social phenomena that have important implications in defining an organisation's capability for effective change. Therefore, a reductionist approach to organisational inquiry is not desirable and may not be effective for real change. The research will draw on various concepts within the frameworks of systems thinking, complexity theory, knowledge management and dynamic capabilities to elicit themes to complement Nedbank's existing transformation process. The results provide recommendations on how management's contemporary role is required to transform in order to address the challenges of organisational change in the knowledge world. / Thesis (M.Sc.)-University of KwaZulu-Natal, Durban, 2005.

A test cryostat was constructed to investigate the potential of a locally made thermal battery. A thermal battery is proposed to be a useful component in the construction of future superconducting fault current limiter (SFCL) systems. The heat generated from a SFCL under quench conditions can be conducted into a solid nitrogen thermal battery. This is an alternative to using a liquid cryogen which on evaporation would form a highly nonconductive vapour layer around the SFCL and could be potentially explosive. The relevant heat transfer mechanisms for cryostat design were analyzed to ensure that the cryostat was capable of solidifying nitrogen and thus be used as a thermal battery. The experimental stage was ultimately capable of reaching a temperature of 40 K. Using a resistor to mimic the normal state of a superconductor, the performance of the thermal battery was determined by subjecting it to transient thermal events. The effect of solid nitrogen crystal size was investigated by performing pulse tests on solid nitrogen formed at different rates. It was found that slowly formed solid nitrogen performed better and stabilised the resistor’s temperature more quickly. The phenomenon of ‘dry-out’ was also investigated for different formation rates by subjecting the solid nitrogen to multiple heating pulses. It was found to become very significant after the first pulse when using quickly formed solid nitrogen, but did not manifest in slowly formed solid nitrogen. / Thesis (M.Sc.Eng.)-University of KwaZulu-Natal, Durban, 2011.

In order to address rain attenuation scattering of millimetric waves and microwave sin Botswana, we have employed a comparison technique to determine the Ro.o1 at fourteen diverse locations in Botswana. In addition we have identified two rain climatic zones for Botswana. We note that Matzler employs Mie Scattering technique to determine the specific attenuation due to rain in Central Europe. Both Matzler and Olsen use the exponential distribution of N(D) to calculate y. In this dissertation we use the Mie scattering approach, but assume several distributions, including the log-normal distribution of N(D) as expounded by Ajayi et aI., to determine y for tropical and subtropical regions of Africa. The results show that the extinction coefficients depend more strongly on temperature at lower frequencies than at higher frequencies for lognormal distribution: at selected frequencies, we record high attenuation values at rising SHF bands: at 300 GHz, tropical showers take on values of 12, 12.5, 11.9 and 14 dB/km for Gaborone, Francistown, Kasane and Selebi-Phikwe, respectively. The absorption coefficient is significant but decreases exponentially with rain temperature at lower microwave frequencies. The application of the proposed model (Continental Thunderstorm is shown using practical results from Durban) is corroborated using practical results from Durban. Further, based on attenuation measurements, it is found that the lognormal distribution is suitable for Durban at rain rates greater than or equal to 21 mm/h. At rain rates below this, the loss-Thunderstorm is the better fit. Finally in this dissertation the results show that for rainfall intensity below about 10 mm/h for Marshall-Palmer (MP), Joss-Drizzle (JD), Joss-Thunderstorm (JT) and Law-Parson (LP) distributions, and below about 4 mm/h for Continental-Showers (CS), Tropical Showers (TS), Continental Thunderstorms (CT) and Tropical Thunderstorm (TT) distributions, the specific rain backscattering follows Rayleigh scattering law where the rain drops are small with respect to the wavelength when the frequency is 19.5 GHz. At rain rates above 10 mm/h for exponential distribution, and above 4 mm/h for lognormal distribution, the specific backscattering follows Mie scattering law. When the received echo power from rain becomes significant, it contributes to the rise in the noise floor and the radar receiver can lose its target. In addition, the result shows that Mie backscattering efficiency is highest at a raindrop diameter of 4.7mm. / Thesis (M.Sc.Eng.)-University of KwaZulu-Natal, Durban, 2008.

The success of the wavelet transform in the compression of still images has prompted an expanding effort to exercise this transform in the compression of video. Most existing video compression methods incorporate techniques from still image compression, such techniques being abundant, well defined and successful. This dissertation commences with a thorough review and comparison of wavelet still image compression techniques. Thereafter an examination of wavelet video compression techniques is presented. Currently, the most effective video compression system is the DCT based framework, thus a comparison between these and the wavelet techniques is also given. Based on this review, this dissertation then presents a new, low-complexity, wavelet video compression scheme. Noting from a complexity study that the generation of temporally decorrelated, residual frames represents a significant computational burden, this scheme uses the simplest such technique; difference frames. In the case of local motion, these difference frames exhibit strong spatial clustering of significant coefficients. A simple spatial syntax is created by splitting the difference frame into tiles. Advantage of the spatial clustering may then be taken by adaptive bit allocation between the tiles. This is the central idea of the method. In order to minimize the total distortion of the frame, the scheme uses the new p-domain rate-distortion estimation scheme with global numerical optimization to predict the optimal distribution of bits between tiles. Thereafter each tile is independently wavelet transformed and compressed using the SPIHT technique. Throughout the design process computational efficiency was the design imperative, thus leading to a real-time, software only, video compression scheme. The scheme is finally compared to both the current video compression standards and the leading wavelet schemes from the literature in terms of computational complexity visual quality. It is found that for local motion scenes the proposed algorithm executes approximately an order of magnitude faster than these methods, and presents output of similar quality. This algorithm is found to be suitable for implementation in mobile and embedded devices due to its moderate memory and computational requirements. / Thesis (M.Sc.Eng.)-University of Natal, Durban, 2003.

The increased application of digital terrestrial microwave radio links in communication networks has renewed attention in techniques of estimating the probability of multipath fading distributions. Nevertheless, the unpredictable variation of the wireless transmission medium remains a challenge. It has been ascertained that the refraction of electromagnetic waves is due to the inhomogeneous spatial distribution of the refractive index, and causes adverse effects such as multipath and diffraction fading. The knowledge of the characteristics of such causes of these fading phenomena is essential for the accurate design of terrestrial line of sight (LOS) links of high performance and availability. Refractivity variation is random in space and time and cannot be described in a deterministic manner and has to be considered as a random variable with probabilistic characteristics. In this dissertation, radiosonde soundings data is used in characterizing the atmospheric conditions and determining the geoclimatic factor K used in predicting the distribution of multipath fading for five locations in South Africa. The limitations of radiosonde measurements are lack of time resolution and poor spatial resolution. The latter has been reduced by spatial interpolation techniques in our study, specifcally, the Inverse Distance Weighting (IDW) method. This is used in determining the point refractivity gradient not exceeded for 1 % of the time from which the geoclimatic factor is estimated. Fade depth and outage probability due to multipath propagation is then predicted from the International Telecommunications Union Recommendations (ITU-R) techniques. The results are compared with values from Central Africa. The results obtained using the ITU-R method are also compared with region-based models of Bannett-Vigants of USA and Morita of Japan. Three spatial interpolation techniques (Kriging, Thin-Plate Spline and Inverse Distance Weighting) are then used in interpolating the geoclimatic factor K in places where radiosonde data is not available. The estimated values have been used to develop contour maps for geoclimatic factor K for South Africa. Statistical assessment of these methods is done by calculating the root mean square error (RMSE) and the mean absolute error (MAE) between a set of control points and the interpolated results. The best performing method is used to map the seasonal geoclimatic factor K for the entire study region. The estimated values of geoclimatic factor will improve accuracy in predicting outage probability due to multipath propagation in LOS links in the region which is a key contribution of this work. / Thesis (M.Sc.Eng.)-University of KwaZulu-Natal, Durban, 2013.

Recent advances in fiber optics technology have enabled extremely high-speed transport of different forms of data, on multiple wavelengths of an optical fiber, using Dense Wavelength Division Multiplexing (DWDM). It has now become possible to deploy high-speed, multi-service networks using DWDM technology. As the amount of traffic carried has increased, any single failure can be catastrophic. Survivability becomes indispensable in such networks. Therefore, it is imperative to design networks that can quickly and efficiently recover from failures. Most research to date in survivable optical network design and operation focuses on single link failures, however, the occurrence of multiple-link failures are not uncommon in networks today. Multi-link failure scenarios can arise out of two common situations. First, an arbitrary link may fail in the network, and before that link can be repaired, another link fails, thus creating a multi-link failure sequence. Secondly, it might happen in practice that two distinct physical links may be routed via the same common duct or physical channel. A failure at that shared physical location creates a logical multiple-link failure. In this dissertation, we conduct an intensive study of mechanisms for achieving survivability in optical networks. From the many mechanisms presented in the literature the focus of this work was on protection as a mechanism of survivability. In particular four protection schemes were simulated and their results analyzed to ascertain which protection scheme achieves the best survivability in terms of number of wavelengths recovered for a specific failure scenario. A model network was chosen and the protection schemes were evaluated for both single and multiple link and node failures. As an indicator of the performance of these protection schemes over a period of time average service availability and average loss in traffic for each protection scheme was also simulated. Further simulations were conducted to observe the percentage link and node utilization of each scheme hence allowing us to determine the strain each protection scheme places on network resources when traffic in the network increases. Finally based on these simulation results, recommendations of which protection scheme and under what failure conditions they should be used are made. / Recent advances in fiber optics technology have enabled extremely high-speed transport / Thesis (M.Sc.)-University of KwaZulu-Natal, 2006. / Thesis (M.Sc.Eng.)-University of KwaZulu-Natal, 2006.

Thesis (MScIng)--University of Stellenbosch, 2007. / ENGLISH ABSTRACT: The quadrifilar helix antenna has frequently been employed to provide the wide angle, circularly polarized radiation pattern which is preferable for mobile satellite communications. A detailed study of this antenna and its varieties is presented. When used as an element in wide angle scanning arrays for aeronautical satellite tracking applications, the additional requirement of a low profile with light weight applies. This further complicates the realization of good circular polarization close to the horizon. A top disk is incorporated into various antenna structures in an effort to improve the radiation performance when used within a closely spaced array while reducing the height of the radiating element. The array performance of these elements are investigated which hints at a supported traveling mode aiding the ability to accomplish the wide angle beam steering. Subsequent study of leakywave antennas initiated the study and implementation of leaky-wave structures in phased arrays of quadrifilar helix elements. / AFRIKAANSE OPSOMMING: Die vierledige heliksantenna word dikwels gebruik vir toepassings wat ’n wye, sirkulêr gepolariseerde stralingspatroon benodig. ’n Verskeidenheid van hierdie antennas is noukeurig bestudeer en hul toepaslikheid vir mobiele sattelietkommunikasie ondersoek. Wanneer hierdie antennas in fase gestuurde skikkings gebruik word, word dit ook vereis dat die eenhede liggewig is met ’n lae profiel. Dit bemoeilik die verkryging van goeie sirkulêre polarisasie naby die horison aansienlik. In ’n poging om die wyehoek straling met kort antennas te verbeter, is ’n oorhoofse skyf tot verskillende heliksstrukture toegevoeg. In nou gespasieerde skikkings maak hierdie skywe ’n positiewe bydrae to wyehoekstralingeienskappe. Die invloed van lekmodusse wat binne die struktuur voortplant is ondersoek en gebruik in skikkings waarvan die bundel naby aan die horison gestuur word.

Thesis (PhD (Electric and Electronic Engineering))--University of Stellenbosch, 2006. / This study focuses on the drive control system of a novel direct field and torque current control applied to a six-phase induction motor. Special phase current waveforms that make it possible to have separate field and torque windings and currents in the motor are proposed. In this thesis the control of these field and torque windings to control directly the flux and torque of the motor is investigated. With the special phase current waveforms the performance of the six-phase induction motor is evaluated through theoretical and finite element analysis. In the analysis the air gap resultant field intensity and flux density produced by the stator field, stator torque and rotor currents are investigated. It is shown that with the special current waveforms a quasi-square shaped, smooth rotating air gap flux density is generated. This smooth rotating flux is important for proper induction motor operation. An equation for the electromagnetic torque is derived and used in the theoretical calculations. The ease of the torque performance calculations is conspicuous. An approximate magnetic circuit calculation method is developed to calculate the air gap flux density versus field current relationship taking magnetic saturation into account. The air gap MMF harmonics and the per phase self and mutual inductances are analysed and calculated using, amongst other things, winding functions. In the finite element analysis specific attention is given to the MMF balanced condition (zero quadrature flux condition) in the motor and the development of a per phase equivalent model. The drive system’s performance with the proposed direct control technique is verified by a developed Matlab simulation model and measurements on a small (2 kW) two-pole, six-phase induction motor drive under digital hysteresis current control. It is shown in the thesis that the calculated results from theoretical derived equations are in good agreement with finite element and measured results. This is particularly the case for the formulas of the MMF balanced constant (zero quadrature flux linkage constant) used in the control software. The results of the simulated and measured linear relationship between the torque and torque current show that MMF balance is maintained in the motor by the drive controller independent of the load condition. The direct control of the torque also explains the good measured dynamic performance found for the proposed drive.