No description available.

The effect of the configuration of the confining magnetic field on the operating characteristics of a planar magnetron has been observed. In particular, the heat load and charged particle bombardment of the substrate were measured. A circular planar magnetron was constructed with a magnetic field which could be controlled by the adjustment of the current flowing through coils placed around the circumference and with a separate supply feeding a coil around the centre pole. This allowed the magnetic field configuration to be unbalanced and caused the negative glow plasma to be incident on the substrate. It was found that the "unbalanced" electrically-controlled model could give six times the heat load to a substrate in comparison with a balanced permanent magnet structure. Such a load resulted from the bombardment of the substrate with the plasma (revealed by the measurement of the I-V characteristics), and gave a 30 volt negative bias as well as saturated electron and ion currents of around 90 and 1 mA respectively (a magnetron operating current: 0.8A). The heat load was lkWm⁻². This compared to a 1 volt positive bias with current of 1.4 and 0.5 mA for the balanced case. This bombardment was used as a neutralised ion beam to enhance film growth during sputtering. The effect of the magnetic field configuration has been observed on the operating characteristics of a planar magnetron. In particular, the deposition rate, the currents to a probe and heat load, as a function of the outer pole solenoid current, were measured. The deposition rate/input power was constant at 19 mÅ/s/W, independent of the outer pole solenoid current. In the region from 20 to 40 A of the outer pole solenoid current, the configuration of the magnetic field seemed to be concentric and the electrons were confined by it. But from 40 to 80 A, the magnetic field became dispersed outwards along the direction to the magnetron and the electrons followed it. Consequently, following bombardment of the surface by electrons and neutralising ions, the currents to a probe and the heat load, gave a behaviour. The effect of the pressure has been observed on probe current, floating potential and heat load. With the pressure increasing, they decreased. It seems that the mean free path of particles becomes shorter and then scattering of them increases. The influence of the magnetic field strength on the plasma, created at the rear of a substrate, has been observed. In particular, the floating potential and the charged particle bombardment of the substrate were measured. Permanent magnets at the rear of the substrate, outside of the chamber, could make the configuration of the magnetic field change and control the floating potential from -3 to -59 V. At the same time, they influenced the current-voltage characteristics of a probe and made it change following the direction of the field. Ti0₂ is a very important thin film material in optics because the refractive index is high and it can also satisfy the requirements of a hard, dense and chemically stable coating. In our study, the effect of the floating potential, and the resulting ion beam bombardment on the properties of Ti0₂ thin films deposited by reactive planar magnetron sputtering, has been observed. In reactive magnetron sputtering of Ti0₂, as the partial pressure of oxygen is increased, reaction products form on the target (it is poisoned) which lead to an unstable situation with the cathode switching from metal to oxide uncontrollably. More sophisticated control techniques are required in order to get a stoichiometric Ti0₂, film. The oxygen flow was controlled by observation of the light emission of the Ti spectral line. This was measured using a band pass filter and a photomultiplier. It maintained the oxygen flow by regulating a piezovalve. The optical emission controller gave a complete range of Ti to oxygen ratios. As a result, we obtained samples with a high refractive index of 2.52 at 633 nm and a high deposition rate of 4 Å/s. The properties measured were the refractive index, the surface composition and morphology, and the crystallinity. The relationship between the refractive index and the proportions of 'anatase' and 'rutile' crystal structures of the Ti0₂ films was especially considered and the dependence on the floating potential was assessed. Also, Al₂0₃, Cuo, ZnO have been sputtered and the effect of pressure instability assessed. Their properties were measured.

No description available.

This thesis report presents a new design of a synchronization unit for high power impulse magnetron sputtering (HiPIMS) applications used for depositing thin films. The proposed system is composed of two major hardware parts: a microcontroller unit (MCU) and a field-programmable gate array (FPGA). The control range of the new system is increased by at least ten times compared to existing synchronization unit designed by Ionautics AB.In order to verify the system and benchmark its innovations, several batches of the thin film have been deposited using the new technology. It is shown that HiPIMS with synchronized pulsed substrate bias can effectively improve coating performance. Pulsed substrate bias with user-defined pulse width and delay time is possible to use in the new control mode proposed by this master thesis work; Bias mode. As a result, this master thesis work enables users to flexibly control the HiPIMS processes.

Thin films and coatings of oxides are used in various fields of science and technology, such as semiconductor and optoelectronic devices, gas sensors, protective and wear resistant coatings etc. Of late, there has been a tremendous interest in pure and doped vanadium dioxide as thermoelectric switch material. VO2 has been doped with hetero-atoms such as W, Mo, Nb, Ti etc. and effects of doping have been correlated with feasibility of being used as a smart window material. The oxide Al2O3 has been studied as an alternative gate dielectric. Ga2O3 is also a contender for replacing SiO2 as a dielectric material. Atomic layer deposition (ALD) is a technique for the deposition of thin films of various materials and is found to be of considerable scientific and technological importance. In particular, using β-diketonate complexes as precursors is very useful in preparing thin films of oxides, as these precursors already contain a metal-oxygen bond. In this thesis, β-diketonate complexes have been used as precursors for deposition of thin films. The thesis has been divided into two parts: First part deals with deposition and characterization of thin films of VO2 on glass and fused quartz. The second part deals with synthesis and chemical and thermal characterization of bimetallic Al-Ga acetylacetonates along with thin film deposition using the same. Chapter 1 presents a brief introduction to application of thin films of oxides in various fields of science and technology. A brief introduction to the ALD reactor used for the current work is also presented. The importance of thermal analysis of precursors for CVD is briefly reviewed. Chapter 2 deals with the instruments and methods used for the work done for this thesis. In Chapters 3 and 4 of the thesis, a detailed study of deposition of VO2 films on glass and fused quartz has been presented. The films deposited have been analyzed using a host of techniques, for their texture, microstructure and electrical properties. In spite of chemical similarities, considerable differences in structure and properties have been observed between the films deposited on the two substrates. These differences have been explained on the basis of the small chemical differences between the two substrates. Chapters 5, 6 and 7 deal with synthesis, thermal characterization and use of bimetallic Al-Ga precursors, respectively. The bimetallic acetylacetonates have been synthesized using ‘homogenization in solution’ approach. Chemical characterization of the precursors revealed that nominal percentages of Al and Ga are retained in the solid precursors. Single crystal structure confirmed the observation. Thermal analysis of the precursors showed that the precursors, which are solid solutions of Al and Ga acetylacetonates, show negative deviation from the Raoult’s Law. Films were deposited using these precursors and were found to near completely retain the composition of the precursors. Chapter 8 of the thesis presents the conclusions of the current work and proposes future directions.

Sensors is one of the major areas of current research. Thin film micro/nano sensors are gaining attention worldwide, as there is necessity of miniaturization. There are varieties of sensors available by utilizing different materials in bulk and thin film form for measuring parameters like temperature, pressure, flow, humidity etc. Apart from these, there are various sensors available to measure impact force. Impact sensor offers potential application possibilities in robotics, aerospace, structural & mechanical engineering and related areas. Many physical principles have been explored for the realization of impact sensor. The present thesis reports the efforts made in developing impact sensor using piezoelectric thin film. The necessary brief background information on impact sensors is presented in Chapter 1. This includes the description of available literature on impact sensors and their probable applications. In Chapter 2, a review of the various techniques such as thin film deposition techniques, film thickness measurement techniques, thin film characterization techniques, used in our work are explained in detail. Chapter 3 explains the direct and indirect methods of characterization used for confirming the piezoelectric property of zinc oxide thin films. The detailed experimental work carried out in realizing the impact sensor using piezoelectric thin films is presented in chapter 4. This includes design of the sensor, calibration setup used & the procedure followed and results obtained. Finally, we present the summary of the work carried out in the thesis, conclusions arrived at and the scope for carrying out further work in the direction of making the sensor more efficient.

Research on the characterisation and understanding of pulsed magnetron discharges used for the deposition of thin, especially dielectric, films has been carried out between 2003 and 2008 at Chemnitz University of Technology. This thesis is a collection and summary of the original research during this period. In the main part of the thesis, work published in peer-reviewed scientific papers is summarised and yet unpublished results are given in more detail. Different aspects highlighted in the publications are described in a general context of the characterisation of the pulsed discharges for the principal understanding. The cross-linking of the published results is addressed and where necessary extensions to the publications are given. The main part is organised in three sections. In the first one, basics of pulsed magnetron discharges, their application, and important questions are summarised. The second section describes general results and physics of the discharges that have been obtained during the research work. It also emphasises the successful development or modifications of experimental techniques for the time-resolved characterisation. The third section addresses the possibilities to modify and control the process by external parameters that are typically accessible during the application or required by it. An appendix to the thesis comprises selected published research work which is made available as reprints of the original publications. Other publications which are not included as reprints are referenced to in the main part. / Untersuchungen zur Charakterisierung und zum Verständnis gepulster Magnetronentladungen, die zur Abscheidung von dünnen Schichten, besonders von dielektrischen Schichten, verwendet werden, wurden in den Jahren 2003 bis 2008 an der Technischen Universität Chemnitz durchgeführt. Diese Arbeit ist eine Sammlung und Zusammenfassung von neuen Forschungsergebnissen, die in diesem Zeitraum gewonnen wurden. Im Hauptteil der Habilitationsschrift werden die Arbeiten, die in referierten wissenschaftlichen Zeitschriften erschienen sind, zusammengefasst und noch unveröffentlichte Ergebnisse ausführlicher beschrieben. Verschiedene Aspekte, die in den Veröffentlichungen herausgestrichen wurden, werden in einem allgemeinen Zusammenhang der Charakterisierung gepulster Entladungen für ein prinzipielles Verständnis dargestellt. Querverbindungen zwischen den veröffentlichten Ergebnissen werden herausgearbeitet und wo nötig werden Erweiterungen der Originalveröffentlichungen vorgenommen. Der Hauptteil der Habilitationsschrift ist in drei Abschnitte unterteilt. Im ersten Teil werden Grundzüge gepulster Entladungen, ihre Anwendung und wesentliche Fragestellungen zusammengefasst. Der zweite Abschnitt beschreibt allgemeine Ergebnisse und die Physik der Entladungen, die während der Forschungsarbeit herausgearbeitet wurden. Er stellt auch die erfolgreiche Neuentwicklung oder Modifikation von Messtechniken zur zeitaufgelösten Charakterisierung heraus. Der dritte Abschnitt befasst sich mit den Möglichkeiten, den Beschichtungsprozess durch externe Parameter, die typischerweise während der Prozessanwendung zugänglich oder auch erforderlich sind, zu modifizieren und zu steuern. Der Anhang der Schrift beinhaltet ausgewählte Originalveröffentlichungen, die in Form von Reprints zugänglich gemacht werden. Andere Veröffentlichungen, die nicht im Anhang enthalten sind, werden im Hauptteil zitiert.

Research on the characterisation and understanding of pulsed magnetron discharges used for the deposition of thin, especially dielectric, films has been carried out between 2003 and 2008 at Chemnitz University of Technology. This thesis is a collection and summary of the original research during this period. In the main part of the thesis, work published in peer-reviewed scientific papers is summarised and yet unpublished results are given in more detail. Different aspects highlighted in the publications are described in a general context of the characterisation of the pulsed discharges for the principal understanding. The cross-linking of the published results is addressed and where necessary extensions to the publications are given. The main part is organised in three sections. In the first one, basics of pulsed magnetron discharges, their application, and important questions are summarised. The second section describes general results and physics of the discharges that have been obtained during the research work. It also emphasises the successful development or modifications of experimental techniques for the time-resolved characterisation. The third section addresses the possibilities to modify and control the process by external parameters that are typically accessible during the application or required by it. An appendix to the thesis comprises selected published research work which is made available as reprints of the original publications. Other publications which are not included as reprints are referenced to in the main part. / Untersuchungen zur Charakterisierung und zum Verständnis gepulster Magnetronentladungen, die zur Abscheidung von dünnen Schichten, besonders von dielektrischen Schichten, verwendet werden, wurden in den Jahren 2003 bis 2008 an der Technischen Universität Chemnitz durchgeführt. Diese Arbeit ist eine Sammlung und Zusammenfassung von neuen Forschungsergebnissen, die in diesem Zeitraum gewonnen wurden. Im Hauptteil der Habilitationsschrift werden die Arbeiten, die in referierten wissenschaftlichen Zeitschriften erschienen sind, zusammengefasst und noch unveröffentlichte Ergebnisse ausführlicher beschrieben. Verschiedene Aspekte, die in den Veröffentlichungen herausgestrichen wurden, werden in einem allgemeinen Zusammenhang der Charakterisierung gepulster Entladungen für ein prinzipielles Verständnis dargestellt. Querverbindungen zwischen den veröffentlichten Ergebnissen werden herausgearbeitet und wo nötig werden Erweiterungen der Originalveröffentlichungen vorgenommen. Der Hauptteil der Habilitationsschrift ist in drei Abschnitte unterteilt. Im ersten Teil werden Grundzüge gepulster Entladungen, ihre Anwendung und wesentliche Fragestellungen zusammengefasst. Der zweite Abschnitt beschreibt allgemeine Ergebnisse und die Physik der Entladungen, die während der Forschungsarbeit herausgearbeitet wurden. Er stellt auch die erfolgreiche Neuentwicklung oder Modifikation von Messtechniken zur zeitaufgelösten Charakterisierung heraus. Der dritte Abschnitt befasst sich mit den Möglichkeiten, den Beschichtungsprozess durch externe Parameter, die typischerweise während der Prozessanwendung zugänglich oder auch erforderlich sind, zu modifizieren und zu steuern. Der Anhang der Schrift beinhaltet ausgewählte Originalveröffentlichungen, die in Form von Reprints zugänglich gemacht werden. Andere Veröffentlichungen, die nicht im Anhang enthalten sind, werden im Hauptteil zitiert.

The master’s thesis deals with the theory of thin film technology, especially creating these layers. The work includes the distribution of vacuum deposition techniques for physical (PVD) and chemical (CVD). The main aim is to create a theme in different ways of implementation by using magnetron sputtering device, and these motives evaluated in terms of the quality of sputtering.

Research on the characterisation and understanding of pulsed magnetron discharges used for the deposition of thin, especially dielectric, films has been carried out between 2003 and 2008 at Chemnitz University of Technology. This thesis is a collection and summary of the original research during this period. In the main part of the thesis, work published in peer-reviewed scientific papers is summarised and yet unpublished results are given in more detail. Different aspects highlighted in the publications are described in a general context of the characterisation of the pulsed discharges for the principal understanding. The cross-linking of the published results is addressed and where necessary extensions to the publications are given. The main part is organised in three sections. In the first one, basics of pulsed magnetron discharges, their application, and important questions are summarised. The second section describes general results and physics of the discharges that have been obtained during the research work. It also emphasises the successful development or modifications of experimental techniques for the time-resolved characterisation. The third section addresses the possibilities to modify and control the process by external parameters that are typically accessible during the application or required by it. An appendix to the thesis comprises selected published research work which is made available as reprints of the original publications. Other publications which are not included as reprints are referenced to in the main part. / Untersuchungen zur Charakterisierung und zum Verständnis gepulster Magnetronentladungen, die zur Abscheidung von dünnen Schichten, besonders von dielektrischen Schichten, verwendet werden, wurden in den Jahren 2003 bis 2008 an der Technischen Universität Chemnitz durchgeführt. Diese Arbeit ist eine Sammlung und Zusammenfassung von neuen Forschungsergebnissen, die in diesem Zeitraum gewonnen wurden. Im Hauptteil der Habilitationsschrift werden die Arbeiten, die in referierten wissenschaftlichen Zeitschriften erschienen sind, zusammengefasst und noch unveröffentlichte Ergebnisse ausführlicher beschrieben. Verschiedene Aspekte, die in den Veröffentlichungen herausgestrichen wurden, werden in einem allgemeinen Zusammenhang der Charakterisierung gepulster Entladungen für ein prinzipielles Verständnis dargestellt. Querverbindungen zwischen den veröffentlichten Ergebnissen werden herausgearbeitet und wo nötig werden Erweiterungen der Originalveröffentlichungen vorgenommen. Der Hauptteil der Habilitationsschrift ist in drei Abschnitte unterteilt. Im ersten Teil werden Grundzüge gepulster Entladungen, ihre Anwendung und wesentliche Fragestellungen zusammengefasst. Der zweite Abschnitt beschreibt allgemeine Ergebnisse und die Physik der Entladungen, die während der Forschungsarbeit herausgearbeitet wurden. Er stellt auch die erfolgreiche Neuentwicklung oder Modifikation von Messtechniken zur zeitaufgelösten Charakterisierung heraus. Der dritte Abschnitt befasst sich mit den Möglichkeiten, den Beschichtungsprozess durch externe Parameter, die typischerweise während der Prozessanwendung zugänglich oder auch erforderlich sind, zu modifizieren und zu steuern. Der Anhang der Schrift beinhaltet ausgewählte Originalveröffentlichungen, die in Form von Reprints zugänglich gemacht werden. Andere Veröffentlichungen, die nicht im Anhang enthalten sind, werden im Hauptteil zitiert.