No description available.

No description available.

Thesis (M.S.)--Virginia Polytechnic Institute and State University, 1994. / Vita. Abstract. Includes bibliographical references (leaves 250-253). Also available via the Internet.

Thesis (Ph. D.)--Ohio State University, 2005. / Title from first page of PDF file. Document formatted into pages; contains xvii, 181 p.; also includes graphics (some col.). Includes bibliographical references (p. 168-181). Available online via OhioLINK's ETD Center

Tribocorrosion is a term used to describe the material degradation due to the combination of electrochemical and tribological processes. Due to a synergetic effect, the material loss can be larger than the sum of the losses due to wear and corrosion acting separately. In this thesis, the synergy of wear and corrosion was investigated for different types of material, namely the Ti-6Al-4V alloy, the SS316L stainless steel coated with a thin film of Diamond Like Carbon (DLC), and the SS301 stainless steel coated with a thin film of chromium silicon nitride (CrSiN). / A tribocorrosion apparatus was designed and constructed to conduct wear experiments in corrosive media. Sliding ball-on-plate configuration was used in this design, where the contact between the ball and the specimen is totally immersed in the test electrolyte. The specimen was connected to a potentiostat to control its electrochemical parameters, namely the potential and the current. Electrochemical techniques were used to control the kinetics of corrosion reactions, and therefore it was possible to assess separately the role of corrosion and wear in the total degradation of material, and to evaluate the synergy between them. / For Ti-6Al-4V, it was found that the corrosion and tribocorrosion depend strongly on the structure of the material. The alpha-equiaxed microstructure with fine dispersed beta-phase exhibited the best corrosion resistance. The corrosion resistance was found to decrease when the basal plane was preferentially aligned parallel to the surface, which is attributed to a low resistance to charge transfer in the oxide films formed on this plane. On the other hand, when wear and corrosion were involved simultaneously, the oxide layer protecting the substrate against dissolution was mechanically destroyed leading to a high corrosion rate. It was found that the hardness was the most important factor determining the tribocorrosion behavior of the Ti-6Al-4V alloy; samples with high hardness exhibited less mechanical wear, less wear-enhanced corrosion, and less corrosion-enhanced wear. / For DLC coatings, it was found that interface engineering plays a crucial role in the tribocorrosion behavior of DLC films. DLC films with nitrided interface layer (SS\N3h\DLC) were shown to have very poor tribocorrosion resistance; the DLC film delaminated from the substrate after 50 cycles of sliding wear at 9 N load in Ringer's solution. It should be mentioned that a previous study performed at Ecole Polytechnique de Montreal [4] has shown that the same coating resisted 1800 cycles of dry wear at 22 N without delamination. This demonstrates clearly the effect of corrosion on the wear resistance of DLC films. The use of a-SiN:H bond layer between the SS316L substrate and the DLC film improved significantly the tribocorrosion behavior of the coating. This layer acts as a barrier against corrosion reaction; the polarization resistance was 5.76 GO.cm2 compared to 27.5 MO.cm2 and 1.81 MO.cm2 for the DLC-coated SS316L with nitrided interface layer and the bare substrate, respectively. / For CrSiN coatings, it was also shown that nitriding treatment of the substrate prior to deposition reduces significantly the tribocorosion resistance of the CrSiN-coated SS301 substrates. This is attributed to the peculiar morphology of the nitrided surface prior to deposition. The high relives at the grain boundaries of the substrate may be the reason for the generation, during sliding wear, of defects in the film, which makes the infiltration of the liquid easier, and consequently leads to the destruction of the CrSiN film.

No description available.

Thesis (Ph. D.)--Mechanical Engineering, Georgia Institute of Technology, 2008. / Committee Chair: David. L. McDowell; Committee Member: Min Zhou; Committee Member: Naresh N. Thadhani; Committee Member: Rami M. Haj-Ali; Committee Member: Richard W. Neu.

Thesis (Ph. D.)--University of Alabama at Birmingham, 1998. / eContent provider-neutral record in process. Description based on print version record. Includes bibliographical references.

Thesis (Ph. D.)--University of Alabama at Birmingham, 1998. / Includes bibliographical references.

Thesis (M.S.)--University of Texas at El Paso, 2009. / Title from title screen. Vita. CD-ROM. Includes bibliographical references. Also available online.