A power assisted wheelchair combines human power, which is delivered by the arms through the pushrims, with electrical motors, which are powered by a battery. Today’s electric power assisted wheelchairs use force sensors to measure the torque exerted on the pushrims by the user. The force sensors in the pushrims are rather expensive and this approach also makes the wheels a little bit clumsy. The objective with this project is to find a new, better and cheaper solution that does not use expensive force sensors in the pushrims. The new power assisted wheelchair will instead only rely on its velocity, which is measured with rotational encoders, as feedback signal and thereby the project name “Torque Sensor Free Power Assisted Wheelchair”. The project consisted of two main parts; an extensive construction part, where an ordinary joystick controlled motorized wheelchair has been rebuild to the new power assisted wheelchair without torque sensors and a development part, where different torque sensor free controllers has been designed, simulated, programmed and tested. The project resulted in a torque sensor free power assisted wheelchair, where the final implemented design is a proportional derivative controller, which gives a very good assisting system that is robust and insensitive to measurement noise. The proportional derivative control design gives two adjustable parameters, which can be tuned to fit a certain user; one parameter is used to adjust the amplification of the user’s force and the other one is used to change the lasting time of the propulsion influence. Since the new assisting control system only relies on the velocity, the torque sensor free power assisted wheelchair will besides giving the user assisting power also give an assistant, which pushes the wheelchair, additional power. This is a big advantage compared to the pushrim activated one, where this benefit for the assistant is not possible.

The master thesis deals with problems of electrical gears divided to the teoretical and practical part of submitted work. Thesis was created in conjuction with company VUES Brno s.r.o. The author of the master thesis accomplished three-month work experience at aforementioned company and consequently solved the national project: Automatic station with utilization of active synchronic brakes for testing electrical hand-held tools. The project included creating full-automatic station for testing life-time cyclic tests electrical hand-held tools. The author of the project engage in programme for frequency transmitter served as headstone of the master thesis.

Malgré le progrès de l'automatisation industrielle, les solutions robotiques ne sont pas encore couramment utilisées dans le secteur du génie civil. Plus spécifiquement, les tâches de ponçage, telles que le désamiantage, sont toujours effectuées par des opérateurs humains utilisant des outils électriques et hydrauliques classiques. Cependant, avec la diminution du coût relatif des machines par rapport au travail humain et les réglementations sanitaires strictes applicables à des travaux aussi risqués, les robots deviennent progressivement des alternatives crédibles pour automatiser ces tâches et remplacer les humains.Dans cette thèse, des nouvelles approches de contrôle de ponçage de surface sont élaborées. Le premier contrôleur est un contrôleur hybride position-force avec poignet conforme. Il est composé de 3 boucles de commande, force, position et admittance. La commutation entre les commandes pourrait créer des discontinuités, ce qui a été résolu en proposant une commande de transition. Dans ce contrôleur, la force de choc est réduite par la commande de transition proposée entre les modes espace libre et contact. Le second contrôleur est basé sur un modèle de ponçage développé et un contrôleur hybride adaptatif position-vitesse-force. Les contrôleurs sont validés expérimentalement sur un bras robotique à 7 degrés de liberté équipé d'une caméra et d'un capteur de force-couple. Les résultats expérimentaux montrent de bonnes performances et les contrôleurs sont prometteurs. De plus, une nouvelle approche pour contrôler la stabilité des manipulateurs mobiles en temps réel est présentée. Le contrôleur est basé sur le « zero moment point », il a été testé dans des simulations et il a été capable de maintenir activement la stabilité de basculement du manipulateur mobile tout en se déplaçant. En outre, les incertitudes liées à la modélisation et aux capteurs sont prises en compte dans les contrôleurs mentionnés où des observateurs sont proposés.Les détails du développement et de l'évaluation des différents contrôleurs proposés sont présentés, leurs mérites et leurs limites sont discutés et des travaux futurs sont suggérés. / Despite the advancements in industrial automation, robotic solutions are not yet commonly used in the civil engineering sector. More specifically, grinding tasks such as asbestos removal, are still performed by human operators using conventional electrical and hydraulic tools. However, with the decrease in the relative cost of machinery with respect to human labor and with the strict health regulations on such risky jobs, robots are progressively becoming credible alternatives to automate these tasks and replace humans.In this thesis, novel surface grinding control approaches are elaborated. The first controller is based on hybrid position-force controller with compliant wrist and a smooth switching strategy. In this controller, the impact force is reduced by the proposed smooth switching between free space and contact modes. The second controller is based on a developed grinding model and an adaptive hybrid position-velocity-force controller. The controllers are validated experimentally on a 7-degrees-of-freedom robotic arm equipped with a camera and a force-torque sensor. The experimental results show good performances and the controllers are promising. Additionally, a new approach for controlling the stability of mobile manipulators in real time is presented. The controller is based on zero moment point, it is tested in simulations and it was able to actively maintain the tip-over stability of the mobile manipulator while moving. Moreover, the modeling and sensors uncertainties are taken into account in the mentioned controllers where observers are proposed. The details of the development and evaluation of the several proposed controllers are presented, their merits and limitations are discussed and future works are suggested.