Railway transportation plays a vital role in modern societies. Due to increasing demands for transportation of passengers and goods, higher speed trains with heavier axle loads are introduced to the railway system, and it is expected to continue in the future. Therefore, track geometry bears huge static and dynamic forces that accelerate degradation process. As a result, railway track should be inspected regularly to detect geometry faults and to plan for maintenance actions in advance. Track geometry inspection has a profound impact on railway track availability and maintenance cost. Although there have been improvements in safety performance and maintenance planning of railway tracks, still infrastructure managers expect a more effective maintenance planning and scheduling regime. This thesis proposes a simulation-based model for optimization of track geometry inspection intervals. To simulate the track geometry evolution a linear model is used to model track geometry degradation in a maintenance cycle. It is assumed that the parameters of degradation model are random variables following lognormal distribution. Using the proposed model, the track geometry behaviour is simulated under different inspection intervals. Later, different inspection intervals are compared with respect to the cost function and the optimal range of inspection intervals is obtained.

The rate at which a railway track deteriorates depends on the response of the track under different static and repeated dynamic forces. These wheel/rail forces lead to imperfections in the rail surface and deviation in track geometry alignment. The wheel/rail forces are dependent upon the quality of maintenance of the characteristics of both train and track. If train components such as wheelsets and suspensions are maintained to a high standard, less dynamic forces are generated at the wheel/rail interface and less damage is caused over time. Therefore, the amount and cost of maintenance of track are reduced. However, there is little known about how the characteristics of train components affect time-dependent track degradation. Track degradation through deviation of track from its ideal position has the most effect on maintenance costs. Therefore, the present research aims to investigate this track degradation and improve understanding of the effects of train characteristics (such as train mass and speed, suspension stiffness and damping) on railway tracks. The research is conducted by looking into the relationship between wheel/rail forces and track degradation on one hand and between wheel/rail forces and train characteristics on the other hand, with the objective of assisting in managing vehicle/track interaction in order to minimise track degradation. This aim is achieved by investigating the above two relationships to attain the desired relationship between track degradation and train characteristics. The research focuses on wheel/rail vertical forces (both amplitudes and frequencies), vertical track alignment (longitudinal vertical profile), and rail head defects. The study started by collecting wheel/rail vertical forces data in addition to data on vertical track degradation under sustained traffic loads on a heavy haul railway section of track in Central Queensland. Also, five years of degradation and maintenance history data were collected on three other test sections of railway track under variety of traffic conditions and loads in Central Queensland. There were four main analyses of this data employed to probe the study. The first analysis was performed by examining the track degradation history data. The standard deviation method was used in this first analysis to acquire the rate of deterioration in terms of its relationship to track profile (roughness). The second analysis was accomplished by correlating the vertical wheel/rail forces to both vertical track profile and rail roughness using signal processing principles and a function know as coherence. The third analysis was carried out by using the computer simulation software NUCARS to obtain the link between wheel/rail forces and the deterioration of the vertical track profile. The fourth analysis was achieved by combining the results obtained from the above three analyses to acquire the rate of track deterioration in terms of its relationship to varying train characteristics. The first analysis mentioned above quantified the relationship between the level of roughness of the track and rate at which that roughness deteriorated. An important outcome of this relationship is that there is a threshold of roughness below which track deterioration is minimal. The track maintenance planners can now use that threshold for cost effective targeting of tamping activities. The correlation study between track roughness and wheel/rail forces using the coherence function found, surprisingly, that the overall deterioration of the track roughness, in the absence of frequencies of forces above 30 Hz, is due to the so-called quasi-static lower frequency oscillations of dynamic forces. This conclusion together with the relationship between vehicle characteristics and track forces, established in the analyses above, has significant implications for the design of wagon bogies and for charges track owners might levy on trains using their tracks. This research is part of a larger Rail CRC project 11/4 called 'Enhancing the Optimisation of Maintenance/Renewal' being carried out in the School of Urban Development in Queensland University of Technology.

Ce travail réalisé dans le cadre d'une collaboration industrielle avec la société ALSTOM Transport porte sur l'étude de la dégradation des voies ferrées urbaines. Les composantes de voie retenus pour cette étude sont le rail et la dalle de voie en béton. Concernant le rail, différents problèmes sont abordés : contact roue – rail, usure du rail, usure ondulatoire du rail, et fatigue de contact de roulement (RCF) du rail. Un outil numérique avec des interfaces graphiques, nommé CONUS, est développé pour le problème de contact roue – rail et le problème d'usure du rail. Des théories classiques (Hertz, Kalker, Archard, etc.) sont implantées dans cet outil. La méthode stationnaire est implantée dans un code de calcul par éléments finis pour étudier l'état asymptotique de l'acier du rail sous le chargement répété des trains. Ceci nous permet de prédire les régimes de RCF du rail. La mécanique de l'endommagement est utilisée pour prédire la fatigue du matériau béton. Le formalisme de Marigo couplé avec le modèle d'endommagement de Mazars permet de modéliser la dégradation progressive de la rigidité du matériau sous chargement cyclique. Une campagne d'essais de fatigue du béton en flexion a été réalisée. Elle a pour but de valider le modèle théorique et d'identifier les paramètres du matériau. Le dimensionnement d'une dalle de voie en béton a fait l'objet d'une application de cette méthode. Le modèle de réseau de poutres (lattice model) a été utilisé pour étudier la propagation des fissures dans les structures en béton. Ce modèle a été implanté dans le logiciel de calcul par éléments finis, CESAR-LCPC. Les résultats numériques (propagation de fissures) obtenus pour les structures simples sous chargement statique sont en tout point comparables avec les résultats d'essais expérimentaux. Ce modèle a ensuite été utilisé pour étudier la fissuration sous chargement de fatigue. Pour cela un modèle d'endommagement simple modélisant la dégradation des éléments «poutres» s'est avéré suffisant pour décrire la cinématique de propagation des fissures / This work is part of the collaboration between the laboratory Navier (UMR ENPC /IFSTTAR/ CNRS) and ALSTOM Transport company (TGS/Trackway). It focuses on the study of the degradation of urban railways. The components of track considered in this study are the rail and the concrete slab. Regarding the rail, different problems are discussed : wheel – rail contact, rail wear, rail corrugation and rolling contact fatigue (RCF). A numerical tool with graphical interfaces, called CONUS, is developed to predict the behaviour of the wheel - rail contact, the rail wear, and the rail corrugation problems. Classical theories (Hertz, Kalker, Archard, etc...) are implemented in this tool. The stationary method is implemented in a finite element software to study the asymptotic state of the rail steel under repeated loading of trains.The damage mechanics is used to predict the fatigue life of concrete. Marigo's formalism coupled with Mazars' damage model is used to predict the gradual degradation of material stiffness under cyclic loading. A campaign of fatigue tests for concrete in bending was conducted. It aims at validating the theoretical model and identifying material parameters. We applied this method in order to design the concrete slabs of urban railway. The lattice model was used to study the crack propagation in concrete structures. This model was implemented in the finite element software, CESAR-LCPC. The numerical results obtained for simple structures under static loading are consistent with the results of laboratory experiments. This model was then used to study the crack propagation under fatigue loading. For that purpose, a simple damage model of degradation of the "beams" elements describes the kinematics of crack propagation with a satisfying accuracy