A major challenge in the design of turbomachinery components for aircraft gas turbine engines is high cycle fatigue failures due to flutter. Of particular concern is the subsonic/transonic stall flutter boundary which occurs at part speed near the stall line. At these operating conditions the incidence angle is large and the relative Mach number is high subsonic or transonic. Viscous effects dominate for high incidence angles. In order to predict the flutter phenomena, accurate calculation of the steady and unsteady aerodynamic loading on the turbomachinery airfoils is necessary. The development of unsteady aerodynamic models to predict the unsteady forces and moments acting on turbomachine airfoils is an area of fundamental research interest. Unsteady Reynolds Averaged Navier-Stokes (RANS) models have been developed to accurately account for viscous effects. For these Reynolds averaged equations turbulence models are needed for the Reynolds stress terms. A transition model is also necessary. The transition onset location is determined by a transition onset model or specified at the suction peak. Usually algebraic, one or two-equation or Reynolds stress turbulence models are used. Since the Reynolds numbers in turbomachinery are large enough to guarantee the flow is turbulent, suitable transition and turbulence models are crucial for accurate prediction of steady and unsteady separated flow. The viscous flow solution of compressor airfoils at off-design conditions is challenging due to flow separation and transition to turbulent flow within separation bubbles. Additional complexity arises when the airfoils are vibrating as is encountered in stall flutter. In this investigation calculations are made of a transonic compressor airfoil in steady flow and with the airfoils oscillating in a pitching motion about the mid-chord at 0° and 10° of chordal incidence angle, and correlated with experiments conducted in the NASA GRC Transonic Flutter Cascade. To model the influence of flow transition on the steady and unsteady aerodynamic flow characteristics, the Solomon, Walker, and Gostelow (SWG) transition model is utilized. The one-equation Spalart-Allmaras model is used to model turbulence. Different transition onset models including fixed onset are implemented and compared for the two incidence angle cases. At each incidence angle, the computational model is compared to the experimental data for the steady flow case and also for pitching oscillation at a reduced frequency of 0.4. The 10° incidence angle case has flow separation over front 40% of the airfoil chord. The operating conditions considered are an inlet Mach number of 0.5 and a Reynolds number of 0.9 Million.

Detached Eddy Simulation (DES) is a hybrid turbulence model, a modification to the one-equation model proposed by Spalart and Allmaras (1997) [26]. It combines the advantages of both the RANS and LES models to predict any fluid flow. Presently, the focus is on using Homogeneous Turbulence to test the DES model. In an attempt to scrutinize this model, many cases are considered involving the variance of DES grid spacing parameter, CDES, the grid density, Reynolds number and cases with different initial conditions. Choosing Homogeneous Turbulence for our study alienates complications related to the geometry, boundary conditions and other flow characteristics helping us in studying the behavior of the model thoroughly. Also, the interdependencies of the model grid spacing parameter, grid density and the numerical scheme used are also investigated. Many previous implementations of the DES model have taken the value of CDES=0.65. Through this work, many issues including the sensitivity of CDES will be made clear. The code used in running the test cases is called LESTool, developed at University of Kentucky, Lexington. The two main test cases considered are based on the benchmark experimental study by Comte Bellot and Corrsin (1971) [12] and the Direct Numerical Scheme (DNS) simulation by Blaisdell et al. (1991) [10].

Since its introduction in 1997, the use of Detached Eddy Simulation (DES) and similar hybrid turbulence techniques has become increasingly popular in the field of CFD. However, with increased use some of the limitations of the DES model have become apparent. One of these is the dependence of DES on grid construction, particularly regarding the point of transition between the Reynolds-Averaged Navier-Stokes and Large Eddy Simulation models. An additional issue that arises with unstructured grids is the definition of the grid spacing in the implementation of a DES length scale. To lay the ground work to study these effects the Spalart-Allmaras one-equation turbulence model, SA based DES hybrid turbulence model, and the Scale Adaptive Simulation hybrid turbulence model are implemented in an unstructured grid CFD code, UNCLE. The implemented SA based DES model is validated for flow over a three-dimensional circular cylinder for three different turbulent Reynolds numbers. Validation included studying the pressure, skin friction coefficient, centerline velocity distributions averaged in time and space. Tools to output the mean velocity profiles and Reynolds stresses were developed. A grid generation code was written to generate a two/three dimensional circular cylinder grid to simulate flow over the cylinder in UNCLE. The models implemented and validated, and the additional tools mentioned will be used in the future.

Title: Solution of inverse problem for a flow around an airfoil Author: Mgr. Jan Šimák Department: Department of Numerical Mathematics Supervisor: prof. RNDr. Miloslav Feistauer, DrSc., dr. h. c., Department of Numerical Mathematics Abstract: The method described in this thesis deals with a solution of an inverse problem for a flow around an airfoil. It can be used to design an airfoil shape according to a specified velocity or pressure distribution along the chord line. The method is based on searching for a fixed point of an operator, which combines an approximate inverse and direct operator. The approximate inverse operator, derived on the basis of the thin airfoil theory, assigns a corresponding shape to the specified distribution. The resulting shape is then constructed using the mean camber line and thickness function. The direct operator determines the pressure or velocity distribution on the airfoil surface. We can apply a fast, simplified model of potential flow solved using the Fredholm integral equation, or a slower but more accurate model of RANS equations with a k-omega turbulence model. The method is intended for a subsonic flow.

Com os grandes avanços ocorridos na disponibilização de computadores, existe uma tendência contínua para a utilização de técnicas computacionais auxiliando no projeto de equipamentos de engenharia. Cada vez mais estão se obtendo resultados bastante próximos às condições reais, incluindo a simulação de motores de combustão interna. Neste sentido o presente trabalho tem o objetivo de analisar o escoamento turbulento no processo de admissão de ar em um motor operando em ciclo Diesel. A investigação é focada na determinação da influência do passo de tempo no cálculo do coeficiente de descarga e razão de swirl. Adicionalmente, o campo de velocidades, pressão, energia cinética turbulenta e outros parâmetros são apresentados e analisados, com o objetivo de auxiliar no entendimento da dinâmica envolvida. Essencialmente, dois modelos de turbulência são empregados, juntamente com dois tratamentos de parede. Seus resultados também são confrontados e discutidos. A geometria considerada é de um motor Fiat 1.9 L quatro tempos com duas válvulas. A análise é concentrada em um único cilindro. O pacote computacional utilizado é o Star-cd, e seu aplicativo es-ice. A independência de malha foi obtida, chegando a 1.672.056 volumes. Os resultados são apresentados de duas formas. A primeira delas refere-se a resultados de simulações em regime permanente, realizadas em boa parte por outros autores, com ênfase na determinação do coeficiente de descarga e razão de swirl, estes confrontados com valores experimentais, visando à validação da metodologia. Fica evidente a importância da escolha do modelo de turbulência na simulação de motores de combustão interna, assim como das funções de interpolação utilizadas. Na segunda parte os resultados referem-se a uma análise transiente, considerando o movimento do pistão e válvulas, a 1500 RPM. Observa-se a grande exigência quanto ao passo de tempo requerido no transiente real, ficando demonstrado que para esta velocidade o menor passo de tempo utilizado, 0,05° (5.5555E-6 s), ainda é insuficiente para alguns momentos do ciclo. É possível notar maior influência no coeficiente de descarga do que na razão de swirl, em relação aos passos de tempo utilizados. A forte dependência do modelo de turbulência nos resultados obtidos é mais uma vez confirmada, conforme o esperado, já que as hipóteses sobre a física do fenômeno são diferentes em cada modelo. Os resultados quanto ao tratamento na parede não apresentaram significantes diferenças, quando aplicados junto ao modelo de turbulência k-ω SST. / Considering the increase in the availability of computers, there is a continuing trend toward the use of computational simulation aiding in the design of engineering equipments. Reasonable results, close to the real conditions, are obtained, including the simulation of internal combustion engines. In this way, the present work has the objective of analyzing the turbulent flow in the air intake process of an engine operating in Diesel cycle. The investigation focuses on the determination of the time step in the calculation of the air discharge coefficient and swirl ratio. Additionally, the turbulent kinetic energy, pressure and velocity fields, besides other parameters, are presented and analyzed, with the objective of aiding in the understanding of the involved dynamics. Essentially, two turbulence models are employed, together with two wall treatments. Their results are also confronted and discussed. The considered geometry is a four-stroke, 1.9-L FIAT engine, with two valves. The analysis is concentrated on a single cylinder. The software package used is the Star-cd, and its application es-ice. The mesh independence is carried out, arriving in 1.672.056 volumes. The results are presented in two ways. The first one refers to simulation results of the steady state, also accomplished by other authors, with emphasis in the determination of the discharge coefficient and swirl ratio. These data are confronted with experimental values, aiming to validate the applied methodology. The importance of the choice of the turbulent model becomes evident in the simulation of internal combustion engines, as well as the interpolation functions used. In the second part the results refer to a transient analysis, considering the valves and piston movement, at 1500 rpm. It is observed the great demand on time step required is observed for the real transient, demonstrating that, for this speed, the smallest time step used, 0.05º (5.5555E-6 s), is still insufficient for some moments of the cycle. Also regarding the time step, it is possible to notice a greater influence in the discharge coefficient than in the swirl ratio. The strong dependence of the turbulence model on the results is once again confirmed, as expected, since the hypotheses about the physics of the phenomenon are different in each model. The results, regarding the wall treatment, presented no significant differences, when applied together with the SST k-ω turbulence model.

Com os grandes avanços ocorridos na disponibilização de computadores, existe uma tendência contínua para a utilização de técnicas computacionais auxiliando no projeto de equipamentos de engenharia. Cada vez mais estão se obtendo resultados bastante próximos às condições reais, incluindo a simulação de motores de combustão interna. Neste sentido o presente trabalho tem o objetivo de analisar o escoamento turbulento no processo de admissão de ar em um motor operando em ciclo Diesel. A investigação é focada na determinação da influência do passo de tempo no cálculo do coeficiente de descarga e razão de swirl. Adicionalmente, o campo de velocidades, pressão, energia cinética turbulenta e outros parâmetros são apresentados e analisados, com o objetivo de auxiliar no entendimento da dinâmica envolvida. Essencialmente, dois modelos de turbulência são empregados, juntamente com dois tratamentos de parede. Seus resultados também são confrontados e discutidos. A geometria considerada é de um motor Fiat 1.9 L quatro tempos com duas válvulas. A análise é concentrada em um único cilindro. O pacote computacional utilizado é o Star-cd, e seu aplicativo es-ice. A independência de malha foi obtida, chegando a 1.672.056 volumes. Os resultados são apresentados de duas formas. A primeira delas refere-se a resultados de simulações em regime permanente, realizadas em boa parte por outros autores, com ênfase na determinação do coeficiente de descarga e razão de swirl, estes confrontados com valores experimentais, visando à validação da metodologia. Fica evidente a importância da escolha do modelo de turbulência na simulação de motores de combustão interna, assim como das funções de interpolação utilizadas. Na segunda parte os resultados referem-se a uma análise transiente, considerando o movimento do pistão e válvulas, a 1500 RPM. Observa-se a grande exigência quanto ao passo de tempo requerido no transiente real, ficando demonstrado que para esta velocidade o menor passo de tempo utilizado, 0,05° (5.5555E-6 s), ainda é insuficiente para alguns momentos do ciclo. É possível notar maior influência no coeficiente de descarga do que na razão de swirl, em relação aos passos de tempo utilizados. A forte dependência do modelo de turbulência nos resultados obtidos é mais uma vez confirmada, conforme o esperado, já que as hipóteses sobre a física do fenômeno são diferentes em cada modelo. Os resultados quanto ao tratamento na parede não apresentaram significantes diferenças, quando aplicados junto ao modelo de turbulência k-ω SST. / Considering the increase in the availability of computers, there is a continuing trend toward the use of computational simulation aiding in the design of engineering equipments. Reasonable results, close to the real conditions, are obtained, including the simulation of internal combustion engines. In this way, the present work has the objective of analyzing the turbulent flow in the air intake process of an engine operating in Diesel cycle. The investigation focuses on the determination of the time step in the calculation of the air discharge coefficient and swirl ratio. Additionally, the turbulent kinetic energy, pressure and velocity fields, besides other parameters, are presented and analyzed, with the objective of aiding in the understanding of the involved dynamics. Essentially, two turbulence models are employed, together with two wall treatments. Their results are also confronted and discussed. The considered geometry is a four-stroke, 1.9-L FIAT engine, with two valves. The analysis is concentrated on a single cylinder. The software package used is the Star-cd, and its application es-ice. The mesh independence is carried out, arriving in 1.672.056 volumes. The results are presented in two ways. The first one refers to simulation results of the steady state, also accomplished by other authors, with emphasis in the determination of the discharge coefficient and swirl ratio. These data are confronted with experimental values, aiming to validate the applied methodology. The importance of the choice of the turbulent model becomes evident in the simulation of internal combustion engines, as well as the interpolation functions used. In the second part the results refer to a transient analysis, considering the valves and piston movement, at 1500 rpm. It is observed the great demand on time step required is observed for the real transient, demonstrating that, for this speed, the smallest time step used, 0.05º (5.5555E-6 s), is still insufficient for some moments of the cycle. Also regarding the time step, it is possible to notice a greater influence in the discharge coefficient than in the swirl ratio. The strong dependence of the turbulence model on the results is once again confirmed, as expected, since the hypotheses about the physics of the phenomenon are different in each model. The results, regarding the wall treatment, presented no significant differences, when applied together with the SST k-ω turbulence model.

CoordenaÃÃo de AperfeiÃoamento de Pessoal de NÃvel Superior / Realizou-se o levantamento de curvas de eficiÃncia utilizando odelos numÃricos RANS de uma e duas equaÃÃes para um erogerador com 3m de diÃmetro, utilizando pÃs projetadas para operar em diferentes condiÃÃes de λ com perfis NACA 0012, 4412 e 6412. A parametrizaÃÃo da geometria da malha para a dimensÃo do rotor, juntamente com a parametrizaÃÃo do refinamento frente à capacidade dos modelos RANS obteve a independÃncia da malha à soluÃÃo. Posteriormente a anÃlise numÃrica realizou a comparaÃÃo do melhor resultado â pà projetada λ=6 com o perfil NACA 6412 â com dados experimentais. O aparato experimental foi capaz de coletar dados de rotaÃÃo e torque do rotor simultaneamente com a mediÃÃo da velocidade do vento, no qual foi obtido um valor mÃximo de eficiÃncia de aproximadamente 25% e uma faixa de operaÃÃo limitada a λ=6. Conclui-se que os modelos fornecem boa precisÃo em predizer a faixa operacional de λ, no entanto os valores de Cp foram subestimados. O modelo k-ω SST apresentou o melhor resultados dentre todos. / A survey was conducted, consisting of efficiency curves applying RANS turbulence numerical models of one and two equations for a wind turbine with a diameter of 3m, using blades designed to operate under different λ with NACA 0012, 4412 and 6412 profiles. The parameterization of the mesh geometry to the size of the rotor, together with the parameterization of the refinement level compared to the ability of RANS models reached independence from the grid to the solution. Later, a numerical analysis was performed to compare the best result â a blade designed to operate under λ = 6 with the NACA 6412 profile - against experimental data. The experimental apparatus was able to collect data rotation and torque of the rotor simultaneously with the measurement of wind velocity, which obtained a maximum efficiency of approximately 25% and an operating range limited to λ = 6. It can be concluded that the models provide good accuracy in predicting the operating range of λ, however the values of Cp were underestimated. The k-ω SST model showed the best results among all.

The aim of this paper is to investigate using of hybrid turbulence models for strongly swirling flows. The work is focused on the possibility of applying a hybrid SBES model to simulate flow around a hydrofoil. The work further describes the creation of a mesh for the solved domain, the setting of boundary conditions and the setting of the solution for the software FLUENT. The simulation results are compared with experimentally measured values. The work also uses and evaluates data from PIV measurements. The knowledge that the paper brings as part of the results of a research project can be applied in the future in the design of blades of water turbines.

This Diploma thesis deals with CFD simulations of flow around vehicles subjected to a crosswind with MIRA Reference Car in three body shapes with a diffuser serving as a vehicle. It contains tuning of computational grid and chosen solver settings in Fluent, mostly for v2f turbulence model. The main output of this thesis is a simulation of all body shapes in several crosswind angles in steady state and one chosen body shape with one chosen crosswind angle in unsteady state. All results are validated against measurements taken with full scale models in MIRA windtunnel.

The present study utilizes the relational turbulence model (RTM) to illuminate stepparent experiences of relational uncertainty and partner interference within the context of the stepparent-biological parent marriage. In-depth, semi-structured interviews with 6 stepparents revealed four primary themes pertaining to how stepparents experienced relational uncertainty: (a) enactment of parenting, (b) competing expectations, (c) shifts in attitude and behavior by spouse, and (d) differences between marriage partners. Interference from partners was experienced by stepparents in relation to the enactment of parenting and the maintaining of the marriage as an intimate relationship.