1 |
Quantification of Fouling during UHT Processing in an Indirect Tubular Heat ExchangerFeldman, Ariella 29 December 2016 (has links)
No description available.
|
2 |
Studies of UHT-plant fouling by fresh, recombined and reconstituted whole milk : a thesis presented in partial fulfilment of the requirements for the degree of Doctor of Philosophy in Food EngineeringSrichantra, Arunee January 2008 (has links)
The objective of this study was to investigate the effects of preheat treatments on fouling by fresh whole milk (FWM), recombined whole milk (RCB) and reconstituted whole milk (Recon) in the high-temperature heater of indirect UHT plants. Various preheat treatments prior to evaporation during milk powder manufacture were applied to skim milk powder (SMP, 75 °C 2 s, 85 °C, 155 s and 95 °C, 155 s) and whole milk powder (WMP, 95 °C, 33 s). These preheat treatments were so-called “evaporator preheat treatments”. Skim milk powder (SMP) and whole milk powder (WMP) were derived from the same original batch of pasteurised FWM to remove the effects of the variation in milk composition between different milk batches. These SMPs were recombined with anhydrous milk fat and water to prepare RCB, and WMPs were reconstituted with water to prepare Recon. Then, (homogenized) FWM, RCB and Recon were subjected to various preheat treatments (75 °C, 11 s, 85 °C, 147 s and 95 °C, 147 s) prior to UHT processing. These preheat treatments were so-called “UHT preheat treatments”. Temperature difference (hot water inlet temperature – milk outlet temperature) was taken as a measure of the extent of fouling in the high-temperature heater. The slope of the linear regression of temperature difference versus time (for two hours of UHT processing) was taken as fouling rate (°C/h). Increasing both evaporator and UHT preheat treatments resulted in increasing fouling rate and total deposit weight for all three whole milk types for several milk batches. In the case of FWM, there was no reduction in fouling rate with increasing UHT preheat treatment whether FWM was homogenized then preheated, preheated then homogenized or not homogenized at all. These findings, which are wholly consistent and well replicated, are in apparent conflict with the results of most previous comparable studies. Possible reasons for this are explained. Further investigations of the effects of homogenization relating to the role of whey protein on the surface of the fat globules showed that whey protein associated with the membrane covering the surface of fat globules for homogenized then preheated FWM, RCB and Recon and that association increased with increasing heating process stage. The increasing association of whey protein with the milk fat globules membrane with increasing severity of heating process stage became faster when preheat treatment was more severe: the association of whey protein plateaued on intermediate temperature heating when the milks were preheated at 75°C, 11 s and on preheating when the milks were preheated at 95°C, 147 s. In the case of FWM, the thickness of the membrane covering the surface of fat globules for homogenized then preheated FWM, which increased with the severity of heating process stage, was greater than the thickness of the membrane in preheated then homogenized FWM. Preheating then homogenization resulted in the greater interfacial spreading of small molecules on the surface of fat globules, i.e. whey protein or small molecules from the disintegration of casein micelles during preheating. Possible basic mechanisms for UHT fouling in the high-temperature heater include: the reduction in the solubility of calcium phosphate and the deposition of protein as fat-bound protein and non-fat-bound protein. When non-fat-bound protein in milk plasma deposited, it could be a carrier for the deposition of mineral, such as, the precipitate of calcium phosphate in the casein micelles or the deposition of complexes between whey protein and casein micelles.
|
3 |
Studies of UHT-plant fouling by fresh, recombined and reconstituted whole milk : a thesis presented in partial fulfilment of the requirements for the degree of Doctor of Philosophy in Food EngineeringSrichantra, Arunee January 2008 (has links)
The objective of this study was to investigate the effects of preheat treatments on fouling by fresh whole milk (FWM), recombined whole milk (RCB) and reconstituted whole milk (Recon) in the high-temperature heater of indirect UHT plants. Various preheat treatments prior to evaporation during milk powder manufacture were applied to skim milk powder (SMP, 75 °C 2 s, 85 °C, 155 s and 95 °C, 155 s) and whole milk powder (WMP, 95 °C, 33 s). These preheat treatments were so-called “evaporator preheat treatments”. Skim milk powder (SMP) and whole milk powder (WMP) were derived from the same original batch of pasteurised FWM to remove the effects of the variation in milk composition between different milk batches. These SMPs were recombined with anhydrous milk fat and water to prepare RCB, and WMPs were reconstituted with water to prepare Recon. Then, (homogenized) FWM, RCB and Recon were subjected to various preheat treatments (75 °C, 11 s, 85 °C, 147 s and 95 °C, 147 s) prior to UHT processing. These preheat treatments were so-called “UHT preheat treatments”. Temperature difference (hot water inlet temperature – milk outlet temperature) was taken as a measure of the extent of fouling in the high-temperature heater. The slope of the linear regression of temperature difference versus time (for two hours of UHT processing) was taken as fouling rate (°C/h). Increasing both evaporator and UHT preheat treatments resulted in increasing fouling rate and total deposit weight for all three whole milk types for several milk batches. In the case of FWM, there was no reduction in fouling rate with increasing UHT preheat treatment whether FWM was homogenized then preheated, preheated then homogenized or not homogenized at all. These findings, which are wholly consistent and well replicated, are in apparent conflict with the results of most previous comparable studies. Possible reasons for this are explained. Further investigations of the effects of homogenization relating to the role of whey protein on the surface of the fat globules showed that whey protein associated with the membrane covering the surface of fat globules for homogenized then preheated FWM, RCB and Recon and that association increased with increasing heating process stage. The increasing association of whey protein with the milk fat globules membrane with increasing severity of heating process stage became faster when preheat treatment was more severe: the association of whey protein plateaued on intermediate temperature heating when the milks were preheated at 75°C, 11 s and on preheating when the milks were preheated at 95°C, 147 s. In the case of FWM, the thickness of the membrane covering the surface of fat globules for homogenized then preheated FWM, which increased with the severity of heating process stage, was greater than the thickness of the membrane in preheated then homogenized FWM. Preheating then homogenization resulted in the greater interfacial spreading of small molecules on the surface of fat globules, i.e. whey protein or small molecules from the disintegration of casein micelles during preheating. Possible basic mechanisms for UHT fouling in the high-temperature heater include: the reduction in the solubility of calcium phosphate and the deposition of protein as fat-bound protein and non-fat-bound protein. When non-fat-bound protein in milk plasma deposited, it could be a carrier for the deposition of mineral, such as, the precipitate of calcium phosphate in the casein micelles or the deposition of complexes between whey protein and casein micelles.
|
4 |
Studies of UHT-plant fouling by fresh, recombined and reconstituted whole milk : a thesis presented in partial fulfilment of the requirements for the degree of Doctor of Philosophy in Food EngineeringSrichantra, Arunee January 2008 (has links)
The objective of this study was to investigate the effects of preheat treatments on fouling by fresh whole milk (FWM), recombined whole milk (RCB) and reconstituted whole milk (Recon) in the high-temperature heater of indirect UHT plants. Various preheat treatments prior to evaporation during milk powder manufacture were applied to skim milk powder (SMP, 75 °C 2 s, 85 °C, 155 s and 95 °C, 155 s) and whole milk powder (WMP, 95 °C, 33 s). These preheat treatments were so-called “evaporator preheat treatments”. Skim milk powder (SMP) and whole milk powder (WMP) were derived from the same original batch of pasteurised FWM to remove the effects of the variation in milk composition between different milk batches. These SMPs were recombined with anhydrous milk fat and water to prepare RCB, and WMPs were reconstituted with water to prepare Recon. Then, (homogenized) FWM, RCB and Recon were subjected to various preheat treatments (75 °C, 11 s, 85 °C, 147 s and 95 °C, 147 s) prior to UHT processing. These preheat treatments were so-called “UHT preheat treatments”. Temperature difference (hot water inlet temperature – milk outlet temperature) was taken as a measure of the extent of fouling in the high-temperature heater. The slope of the linear regression of temperature difference versus time (for two hours of UHT processing) was taken as fouling rate (°C/h). Increasing both evaporator and UHT preheat treatments resulted in increasing fouling rate and total deposit weight for all three whole milk types for several milk batches. In the case of FWM, there was no reduction in fouling rate with increasing UHT preheat treatment whether FWM was homogenized then preheated, preheated then homogenized or not homogenized at all. These findings, which are wholly consistent and well replicated, are in apparent conflict with the results of most previous comparable studies. Possible reasons for this are explained. Further investigations of the effects of homogenization relating to the role of whey protein on the surface of the fat globules showed that whey protein associated with the membrane covering the surface of fat globules for homogenized then preheated FWM, RCB and Recon and that association increased with increasing heating process stage. The increasing association of whey protein with the milk fat globules membrane with increasing severity of heating process stage became faster when preheat treatment was more severe: the association of whey protein plateaued on intermediate temperature heating when the milks were preheated at 75°C, 11 s and on preheating when the milks were preheated at 95°C, 147 s. In the case of FWM, the thickness of the membrane covering the surface of fat globules for homogenized then preheated FWM, which increased with the severity of heating process stage, was greater than the thickness of the membrane in preheated then homogenized FWM. Preheating then homogenization resulted in the greater interfacial spreading of small molecules on the surface of fat globules, i.e. whey protein or small molecules from the disintegration of casein micelles during preheating. Possible basic mechanisms for UHT fouling in the high-temperature heater include: the reduction in the solubility of calcium phosphate and the deposition of protein as fat-bound protein and non-fat-bound protein. When non-fat-bound protein in milk plasma deposited, it could be a carrier for the deposition of mineral, such as, the precipitate of calcium phosphate in the casein micelles or the deposition of complexes between whey protein and casein micelles.
|
5 |
IMPACT OF HOMOGENIZATION AND UHT PROCESSING ON THE EMULSIFICATION AND PHYSICAL PROPERTIES OF PEA PROTEIN BEVERAGESXiang Cheng (17583861) 10 December 2023 (has links)
<p dir="ltr">Pea protein is one of the most used plant proteins in food products, acting as an alternative to conventional animal protein sources due to its abundant, nutritious, and ease in supply chain characteristics. The objective of this study was to investigate the impact of homogenization and UHT processing parameters on the properties of protein emulsion. Protein emulsions (8% w/w pea protein isolate and 1% w/w sunflower oil) were freshly prepared prior to processing, and the untreated sample was considered as the control (NT). The pilot-scale aseptic processing system (APS) used in this study consisted of two coil-in-shell heaters and two coolers. Samples flowed through each section of the APS system following this order: balance tank, pre-heater, final heater, hold tube, pre-cooler, and final cooler. The homogenizer was located either after the pre-cooler (AC) or the pre-heater (AH) with a controlled temperature of 165F. A third setup was utilized by bypassing the homogenizer in the UHT system. An additional 8-hour continuous run was conducted to mimic a commercial manufacturing operation by recirculating the protein emulsion in the UHT system, and fouling detections were made using a non-intrusive sensor (NICS). 5% w/w soy protein, 1% w/w sunflower oil oil-in-water emulsion was also used for fouling tests. Protein concentration, pH and zeta potential, Cryo-SEM microscopic image, particle size distribution, flocculation index (FI), coalescence index (CI), viscosity and color data were collected and analyzed. The protein concentration had a 23.20 ± 4.00 %, 28.35 ± 5.02 %, 27.98 ± 5.05% and 21.38 ± 5.75% reduction for AC, AH, UHT and NT samples, respectively, when compared with the initial concentration in the formula. AC, AH, UHT and NT samples had pH values of 7.24 ± 0.01, 7.27 ± 0.01, 7.28 ± 0.02, 7.41 ± 0.01, and zeta potential values of -42.91 ± 0.89, -47.30 ± 0.91, -46.91 ± 1.40 and -50.11 ± 1.47 mV. AC sample had a smaller and NT sample had a bigger, respectively, mean weighted size D 4,3 value than AH and UHT samples, which could also be seen in Cryo-SEM images where only AC images contained more visually observable smaller particles. FI and CI for AC, AH and UHT indicated the formation of flocs but no irreversible aggregations were found. Shear-thinning AC, AH, UHT and NT samples had viscosity decreases from 4.00 to 3.56, 3.88 to 3.75, 4.02 to 3.79 and 10.42 to 9.56 mPa*s in 1 1/s to 100 1/s shear rate range. NT sample had a very noticeable color difference from the other three treated samples. Overall, AC samples had similar or better emulsion stability in all aspects than AH and UHT samples, suggesting that AC processing could potentially be used in the protein beverage industry for manufacturing products with improved shelf stability. Severe foulants buildups were neither observed nor detected by a non-intrusive continuous sensor (NICS) in the UHT system within 8 hours of process for both pea protein and soy protein emulsion, indicating that this UHT-homogenization processing can potentially be adapted to current industrial practices for higher-quality protein beverages.</p>
|
Page generated in 0.0824 seconds