Transmitted reference pulse cluster (TRPC) was recently proposed for ultrawideband (UWB) communications attributing to its robust performance, higher data rate, enhanced reliability and lower implementation complexity compared with the conventional transmitted reference technique. This thesis investigates the TRPC UWB relay strategies between two nodes lack of a direct link. Two novel channel quality indicators are first proposed for the TRPC UWB system, which can detect the channel condition and the relay decoding quality at the bit level without requiring estimating the channel state information. Five relay strategies based on these indicators (Relay Combining (RC), Weighted Relay Combining (WRC), Outage based Relay Selection (ORS), Maximum Product Relay Selection (MP-RS) and Minimax Relay Selection (MinMax-RS)) are proposed for the cooperative network to extend the network coverage and improve the system performance. The efficiency and effectiveness of the proposed cooperative strategies are examined under different channel environments through simulations, among which the MinMax-RS strategy based on the Log Likelihood Ratio (LLR) channel quality indicator is testified to yield the best performance under the typical indoor line of sight (LOS) environment. Moreover, in order to reduce the relay overhead, a multipath channel based relay selection strategy (MC-RS) is proposed, where the channel quality is detected once for each channel realization and the noise variation in each bit is reasonably neglected. And base on both the channel and bit level selection, a joint relay selection (JRS) strategy is investigated to gain a balance between the channel condition and the bit-by-bit decoding quality at relays. At last, for the two-way-relay system prototype, the power allocation strategies are further investigated to minimize the system outage probability, under the limit of the total transmit power. Simulations in this thesis are executed under various channel environments following the IEEE 802.15.4a standard, and numerical results validate the effectiveness of the proposed strategies. / Graduate

Body Area Network (BAN) technology is related to many applications inside, on and around the human body. The basic configuration of a BAN is a set of sensors, which are wearable or are placed inside the human body, transmitting signals to a terminal situated in a doctor’s office, in order to assess or monitor some aspect of a patient’s physical condition. Additionally, in many BAN applications the information about the sensor location is very important, since without knowing a sensor’s location, the transmitted data may be of limited value. As an example, Wireless Video Capsule Endoscopy (VCE) can benefit greatly from the addition of location information. The capsule transmits an RF signal from inside the human body to another sensor on the body surface or external. From the image data provided by the capsule, taken together with the location information, the doctor can locate the infection or lesion and initiate appropriate medical care. In this way, the treatment can be more effective and accurate. In this thesis we investigate the characteristics of Ultra-Wide Band (UWB) RF propagation for BAN devices placed around and inside the human body. We have made measurements around the human body and around a water-filled phantom using an E8363B Vector Network Analyzer (VNA), specifically measuring the S21 signal, which gives the transfer function. Based on these measurement results, we discuss the channel propagation for cases where the transmitter and the receiver are on the surface of the body and analyze the UWB propagation characteristics for RF localization. Because it is impractical or even impossible to make measurements inside the human body, we chose to apply the measurements using a simulation model of homogenous tissue, which serves as an approximation of the signal propagation environment inside the body. First, by comparing the multipath situation in free space and within a model of homogenous tissue, we are able to analyze the multipath effects inside human body. Then, because of the different characteristics of RF propagation in different bandwidths, we have made measurements at UWB (3GHz to 10GHz), and narrowband (402MHz) frequencies.

In this thesis, a novel transmission structure is proposed for the Direct Sequence Ultra Wide-Band (DS-UWB) systems. The main purpose of the proposed structure is to eliminate the inter-symbol interference caused by the multi-path environment. In DS-UWB systems, shortening the guard interval is one of the possible ways to achieve higher data rates. However, interference will increase inversely with the length of the guard interval because the signal delay spread caused by the multi-path effect will induce inter-symbol interference. In this thesis, a novel transmission structure that utilizes the autocorrelation properties of the perfect sequence is proposed for interference cancellation in DS-UWB systems. Both computer simulation and mathematical analysis are provided for performance evaluation.

Our study investigates the performance of the WUSB standards and compares it to the Wimedia Standard. To the best of our knowledge, no technical contributions exist in the open literature at present simulating WUSB and its performance. The study showed that WUSB can achieve better throughput when bursting is enabled at the maximum burst size and it provides more accurate timing control of device activity than using the standard facilities of the WiMedia MAC. Our study also addresses protocol extensions and improvement to the original WUSB standard to support better Quality of Service (QoS). First improvement enables a di erent reservation mechanism along with contention based access to support higher priority security and medical system monitoring applications. Second improvement enables the host device to use an adaptive packet loss technique to change the packet size dynamically during the data transmission to achieve packet loss less than 10%. Third improvement enables redundancy in the cluster by adding a backup host to prevent mobility failures and changes. This backup host is chosen by a prede ned cost weighting function.

Recently, there is a new trend of demand of a biomedical device that can continuously monitor patients vital life index such as heart rate variability (HRV) and respiration rate. This desired device would be compact, wearable, wireless, networkable and low-power to enable proactive home monitoring of vital signs. This device should have a radar sensor portion and a wireless communication link all integrated in one small set. The promising technology that can satisfy these requirements is the impulse radio based Ultra-wideband (IR-UWB) technology. Since Federal Communications Commission (FCC) released the 3.1GHz-10.6GHz frequency band for UWB applications in 2002 [1], IR-UWB has received significant attention for applications in target positioning and wireless communications. IR-UWB employs extremely narrow Gaussian monocycle pulses or any other forms of short RF pulses to represent information. <p>In this project, an integrated wireless UWB transceiver for the 3.1GHz-10.6GHz IR-UWB medical sensor was developed in the 0.18µm CMOS technology. This UWB transceiver can be employed for both radar sensing and communication purposes. The transceiver applies the On-Off Keying (OOK) modulation scheme to transmit short Gaussian pulse signals. The transmitter output power level is adjustable. The fully integrated UWB transceiver occupies a core area of 0.752mm^2 and the total die area of 1.274mm^2 with the pad ring inserted. The transceiver was simulated with overall power consumption of 40mW for radar sensing. The receiver is very sensitive to weak signals with a sensitivity of -73.01dBm. The average power of a single pulse is 9.8µW. The pulses are not posing any harm to human tissues. The sensing resolution and the target positioning precision are presumably sufficient for heart movement detection purpose in medical applications. This transceiver can also be used for high speed wireless data communications. The data transmission rate of 200 Mbps was achieved with an overall power consumption of 57mW. A combination of sensing and communications can be used to build a low power sensor.

Ultra wide band (UWB) is an emerging technology that recently has gained regulatory approval. It is a suitable solution for high speed indoor wireless communications due to its promising ability to provide high data rate at low cost and low power consumption. Another benefit of UWB is its ability to resolve individual multi-path components. This feature motivates the use of RAKE multi-path combining techniques to provide diversity and to capture as much energy as possible from the received signal. Potential future and rule limitation of UWB, lead to two important characteristics of the technology: high bit rate and low emitting power. Based on the power emission limit of UWB, the only choice for implementation is the low level modulation technology. To obtain such a high bit rate using low level modulation techniques, significant inter-symbol interference (ISI) is unavoidable. </p>Three N (N means the numbers of fingers) fingers RAKE receiver structures are proposed: the N-selective maximal ratio combiner (MRC), the N-selective MRC receiver with least-mean-square (LMS) adaptive equalizer and the N-selective MRC receiver with LMS adaptive combiner. These three receiver structures were all simulated for N=8, 16 and 32. Simulation results indicate that ISI is effectively suppressed. The 16-selective MRC RAKE receiver with LMS adaptive combiner demonstrates a good balance between performance, computation complexity and required length of the training sequence. Due to the simplicity of the algorithm and a reasonable sampling rate, this structure is feasible for practical VLSI implementations.

Our study investigates the performance of the WUSB standards and compares it to the Wimedia Standard. To the best of our knowledge, no technical contributions exist in the open literature at present simulating WUSB and its performance. The study showed that WUSB can achieve better throughput when bursting is enabled at the maximum burst size and it provides more accurate timing control of device activity than using the standard facilities of the WiMedia MAC. Our study also addresses protocol extensions and improvement to the original WUSB standard to support better Quality of Service (QoS). First improvement enables a di erent reservation mechanism along with contention based access to support higher priority security and medical system monitoring applications. Second improvement enables the host device to use an adaptive packet loss technique to change the packet size dynamically during the data transmission to achieve packet loss less than 10%. Third improvement enables redundancy in the cluster by adding a backup host to prevent mobility failures and changes. This backup host is chosen by a prede ned cost weighting function.

Ultra wide band (UWB) is an emerging technology that recently has gained regulatory approval. It is a suitable solution for high speed indoor wireless communications due to its promising ability to provide high data rate at low cost and low power consumption. Another benefit of UWB is its ability to resolve individual multi-path components. This feature motivates the use of RAKE multi-path combining techniques to provide diversity and to capture as much energy as possible from the received signal. Potential future and rule limitation of UWB, lead to two important characteristics of the technology: high bit rate and low emitting power. Based on the power emission limit of UWB, the only choice for implementation is the low level modulation technology. To obtain such a high bit rate using low level modulation techniques, significant inter-symbol interference (ISI) is unavoidable. </p>Three N (N means the numbers of fingers) fingers RAKE receiver structures are proposed: the N-selective maximal ratio combiner (MRC), the N-selective MRC receiver with least-mean-square (LMS) adaptive equalizer and the N-selective MRC receiver with LMS adaptive combiner. These three receiver structures were all simulated for N=8, 16 and 32. Simulation results indicate that ISI is effectively suppressed. The 16-selective MRC RAKE receiver with LMS adaptive combiner demonstrates a good balance between performance, computation complexity and required length of the training sequence. Due to the simplicity of the algorithm and a reasonable sampling rate, this structure is feasible for practical VLSI implementations.

Recently, there is a new trend of demand of a biomedical device that can continuously monitor patients vital life index such as heart rate variability (HRV) and respiration rate. This desired device would be compact, wearable, wireless, networkable and low-power to enable proactive home monitoring of vital signs. This device should have a radar sensor portion and a wireless communication link all integrated in one small set. The promising technology that can satisfy these requirements is the impulse radio based Ultra-wideband (IR-UWB) technology. Since Federal Communications Commission (FCC) released the 3.1GHz-10.6GHz frequency band for UWB applications in 2002 [1], IR-UWB has received significant attention for applications in target positioning and wireless communications. IR-UWB employs extremely narrow Gaussian monocycle pulses or any other forms of short RF pulses to represent information. <p>In this project, an integrated wireless UWB transceiver for the 3.1GHz-10.6GHz IR-UWB medical sensor was developed in the 0.18µm CMOS technology. This UWB transceiver can be employed for both radar sensing and communication purposes. The transceiver applies the On-Off Keying (OOK) modulation scheme to transmit short Gaussian pulse signals. The transmitter output power level is adjustable. The fully integrated UWB transceiver occupies a core area of 0.752mm^2 and the total die area of 1.274mm^2 with the pad ring inserted. The transceiver was simulated with overall power consumption of 40mW for radar sensing. The receiver is very sensitive to weak signals with a sensitivity of -73.01dBm. The average power of a single pulse is 9.8µW. The pulses are not posing any harm to human tissues. The sensing resolution and the target positioning precision are presumably sufficient for heart movement detection purpose in medical applications. This transceiver can also be used for high speed wireless data communications. The data transmission rate of 200 Mbps was achieved with an overall power consumption of 57mW. A combination of sensing and communications can be used to build a low power sensor.

Ultra-Wideband (UWB) technology has become one of the hottest topics in wireless communications, for it provides cost-effective, power-efficient, high bandwidth solution for relaying data in the immediate area (up to 10 meters). This work demonstrates two different solutions for the RF front-end designs in the UWB receivers, one is distributed topology, and the other is based on traditional lumped element topology. The distributed amplifier is one of the attractive candidates for UWB Low Noise Amplifier (LNA). The design, analysis and operation of the distributed amplifiers will be presented. A distributed amplifier is designed with Coplanar Waveguide (CPW) transmission lines in 0.25-μm CMOS process for time domain UWB applications. New design techniques and new topologies are developed to enhance the power-efficiency and reduce the chip area. A compact and high performance distributed amplifier with Patterned Grounded Shield (PGS) inductors is developed in 0.25-μm CMOS process. The amplifier has a measurement result of 7.2dB gain, 4.2-6dB noise figure, and less than -10dB return loss through 0-11GHz. A new distributed amplifier implementing cascade common source gain cells is presented in 0.18-μm CMOS. The new amplifier demonstrates a high gain of 16dB at a power consumption of 100mW, and a gain of 10dB at a low power consumption of 19mW. A UWB LNA utilizing resistive shunt feedback technique is reported in 0.18-μm CMOS process. The measurement results of the UWB LNA demonstrate a maximum gain of 10.5dB and a noise figure of 3.3-4.5dB from 3-9.5GHz, while only consuming 9mW power. Based on the distributed amplifier and resistive shunt-feedback amplifier designs, two UWB RF front-ends are developed. One is a distributed LNA-Mixer. Unlike the conventional distributed mixer, which can only deliver low gain and high noise figure, the proposed distributed LNA-Mixer demonstrates 12-14dB gain ,4-5dB noise figure and higher than 10dB return loss at RF and LO ports over 2-16GHz. To overcome the power consumption and chip area problems encountered in distributed circuits, another UWB RF front-end is also designed with lumped elements. This front-end, employing resistive shunt-feedback technique into its LNA design, can achieve a gain of 12dB and noise figure of 8-10dB through 3-10GHz, the return loss of less than -10dB from 3- 10GHz at RF port, and less than -7dB at LO port, while only consuming 25mA current from 1.8V voltage supply.