The aim of this theis was to design of load-carrying steel structure of shopping mall in two variations. Geometric proposal and examination of structural element was made for both of variations. Then one variant was selected for detailed elaboration of details and drawings.

This thesis focuses on design and assessment of load-bearing construction of a bridge over Jevišovka river at road I/53 near Lechovice. The bridge was designed as a trapezoidal cross-section slab. This solution was chosen from three sketch eventualities. The work includes an implementing engineering report, construction process report and report about static-analysis, the attachments include the sketch, vizualization, drawings, component drawing, construction process and the static-analysis of this structure. Computing of internal forces was performed by computational software Scia Engineer 17.

The aim of the thesis is the design and the assessment of an administrative center in Vimperk. The building is divided into three height levels, the highest has 7 floors. The building is rectangular floor plan with dimensions of 102,5 x 48,0 m. The construction is designed as framing with truss roofing, bracing and purlins for attaching sheathing.

The topic of the thesis is safe and economical design of a bearing bridge structure according to valid regulations and standards. The structure is reviewed by limit states of ultimate and serviceability. The solution includes time dependent analysis of the structure.

This diploma thesis deals with the static review of structure for a football pitch. It is crosswise prestressed reinforced sliding plate with variable cross section. Assessment of the elements was done according to limit states. Internal forces from the load effects were calculated using the SW SciaEngineer 2015.1. The elements were assessed by SW Idea StatiCa 6. The main outputs of this static calculation are drawings of the shape and drawings of the reinforcement.

The experimental studies performed on the behaviour of very thick concrete beams subjected to static loads have revealed that the shear mechanisms play an important role in the overall response and failure behaviour. The aim of this thesis is to recommend suitable design methods for thick concrete beams subjected to off-centre static concentrated load according Eurocode 2 by using non-linear finite element analysis (NLFEA). To achieve this task, Abaqus/Explicit has been used by employing constitutive material models to capture the material non-linearity and stiffness degradation of concrete. Concrete damaged plasticity model and perfect plasticity model has been used for concrete and steel respectively. Three dilation angles (30º, 38º and 45º) and fracture energy from FIB 1990 (76 N/m) and FIB 2010 (142 N/m) has been used to investigate their influence on the finite element model. The dilation angle of 38º and FIB 2010 fracture energy was adopted as the suitable choice that reasonably matched with the experimental results. In verifying and calibrating the finite element model, the experimental results of the thick reinforced concrete beam conducted by the American Concrete Institute have been used. Three design approaches in the ultimate and serviceability limit state according to Eurocode 2 recommendations have been used namely; the beam method, strut and tie method and shell element method. Using the reinforcement detailing of the hand calculations of beam method and strut and tie method and linear finite element analysis of shell element method, non-linear finite element models have been pre-processed and analysed in Abaqus/Explicit. During the post-processing, the results have been interpreted and compared between the three design methods. The results under consideration are hand-calculated load at 0.3 mm crack width, FE-load at 0.3 mm crack width, amount of reinforcement and FE-failure load. The comparison of the results between the three design approaches (beam method, strut and tie method and shell element method) indicates that strut and tie method is better design approach, because it is relatively economic with regards to the quantity of reinforcement bars, has the higher load capacity and has a higher load at crack width of 0.3 mm crack width. / De experimentella studier som utförts på tjocka betongbalkar som utsätts för statisk last har visat att skjuvning spelar en viktig roll i brottmekanismen. Syftet med detta examensarbete är att rekommendera lämpliga dimensioneringsmetoder för tjock betongbalkar utsatt for statisk koncentrerad last enligt Eurokod 2 med hjälp av ickelinjära finita element metod. Abaqus/Explicit användes genom att utnyttja konstitutiva materialmodeller för att fånga materialens icke-linjäritet och minskad styvhet. Tre dilatationsvinklar (30°, 38° och 45°) och två brottenergi från FIB 1990 (76 N/m) och FIB 2010 (142 N/m) tillämpas för att kontrollera deras inverkan på FE-modellerna. Dilatationsvinkel med 38° och FIB 2010 med högre brottenergi valdes i de icke-linjära finita elementanalyserna. Kontroll av FE-modellerna är baserad på ”American Concret Institutes” experimentella resultat på de tjocka betongbalkarna. Handberäkningar av tjocka betongbalkar har utförts i brott- och bruksgränstillstånd med tre dimensioneringsmetoder i Eurokod 2 nämligen balk metoden, fackverksmetoden och linjära-FE skalelementmetoden. Jämförelse har gjorts för de olika dimensioneringsmetoderna, genom att använda de armeringsdetaljer av handberäkningar i de verifierade och kalibrerade icke linjära FE-modellerna i Abaqus/Explicit. Resultaten i fråga är last för 0.3 mm handberäknad sprikvidd, FE-last för 0.3 mm sprikvidd, armeringsmängd och FE-brottlast. Jämförelse av resultaten mellan de tre dimensioneringsmetoder (balkmetod, fackverksmetod och skalelementmetod) visar att fackverksmetod är bättre design metod, eftersom det är relativt ekonomiskt med avseende på armeringsmängd, har högre lastkapacitet och last på 0.3 mm sprickvidd.

The diploma thesis is focused on structural design and assessment of lookout tower. The elements of the lookout tower are made of cast-in-place reinforced concrete except for the stair flight, which is made of prefabricated reinforced concrete. The output of the diploma thesis is a structural design report and drawings of the shape and reinforcement. The calculations were performed using Dlubal RFEM 5.26.02. The drawings was processed by AutoCAD 2020 with the RECOC extension.

This diploma thesis deals with design of steel structure with composite steel-concrete floor structure of a office building.The building is located in Moravský Krumlov. The Office buidling consist of multi-storey building and an entrance atrium. The total ground plan's dimensions are 52,8m x 48,0m. The multi-storey building has 8 floor. The maximum heigh of the building is 25,32m above ground. The project is designed in two options. For winning variant is including check and it is performed a drawings with design and check assembly details and anchorage.

This diploma thesis deals with the design of a metalworking shed with its adjacent administrative center. Both objects are statically independent. The buildings are located in the town of Bučovice. The dimensions of the shed are 54,78x72,58 m. There is an overhead crane situated in the middle wing. The shed‘s height is +11,62 m. The administrative building has L-shaped plan. Its dimensions are 27,62x8,13 m (the wider part is 15,63 m). The design of the administrative object has two variants. Both variants have composite steel-concrete ceiling structure. The heights of the objects are +11,20 m (A variant) and +18,20 m (B variant). For the A variant, drawings were also drawn up with the design and assessment of structural details and anchoring.

The aim of the diploma thesis was to design reinforced concrete construction of the indoor swimming pool and ensure impermeability of the construction, to ensure behavior as concrete tank construction. Static analysis was done by using program Dlubal RFEM 5.12, where interaction of subsoil with construction was taken into account. Slabs around the swimming pool area were divided into expansion section because of temperature changes from glass façade an after that the sealing of expansion gap was solved. Construction system under the swimming was designed and was tested the behavior of walls and slabs. Analysis was done also to considerate of hydration heat. The drawing was done by software CADKON RCD.