This dissertation aims at developing techniques to achieve high power density in motor drives under the performance requirements for transportation system. Four main factors influencing the power density are the main objects of the dissertation: devices, passive components, pulse width modulation (PWM) methods and motor control methods. Firstly, the application of SiC devices could improve the power density of the motor drive. This dissertation developed a method of characterizing the SiC device performance in phase-leg with loss estimation, and claimed that with SiC Schottky Barrier Diode the advantage of SiC JFET could benefit the motor drive especially at high temperature. Then the design and improvement of the EMI filter in the active front-end rectifier of the motor drive was introduced in this dissertation. Besides the classical filter design method, the parasitic parameters in the passive filter could also influence the filtering performance. Random PWM could be applied to reduce the EMI noise peak value. The common-mode (CM) noise reduction by PWM methods is also studied in this dissertation. This dissertation compared the different PWM methods’ CM filtering performance. Considering the CM loop, the design of PWM methods and switching frequency should be together with the CM impedance. Variable switching frequency PWM (VSFPWM) methods are introduced in the dissertation for the motor drive’s EMI and loss improvement. The current ripple of the three-phase converter could be predicted. Then the switching frequency could be designed to adapt the current ripple requirements. Two VSFPWM methods are introduced to satisfy the ripple current peak and RMS value requirements. For motor control issue, this dissertation analyzed the principle of the start-up transient and proposed an improved start-up method. The transient was significantly reduced and the motor could push to high speed and high power with speed sensorless control. Next, the hardware development of modular motor drive was introduced. The development and modification of 10kW phase-legs and full power test of a typical 30kW modular converter is realized with modular design method. Finally, the techniques developed in this dissertation for high power density motor drive design and control are summarized and future works are proposed.

Voltage source inverter (VSI) fed induction motors are increasingly used in industrial and transportation applications as variable speed drives. However, VSIs generate non-sinusoidal voltages and hence result in harmonic distortion in motor current, motor heating, torque pulsations and increased acoustic noise. Most of these undesirable effects can be reduced by increasing the switching frequency of the inverter. This is not necessarily true for acoustic noise. Acoustic noise does not decrease monotonically with increase in switching frequency since the noise emitted depends on the proximity of harmonic frequencies to the motor resonant frequencies. Also there are practical limitations on the inverter switching frequency on account of device rating and losses. The switching frequency of many inverters often falls in the range 2 kHz - 6 kHz where the human ear is highly sensitive. Hence, the acoustic noise emission from the motor drive is of utmost important. Further, the acoustic noise emitted by the motor drive is known to depend on the waveform quality of the voltage applied. Hence, the acoustic performance varies with the pulse width modulation (PWM) technique used to modulate the inverter, even at the same modulation index. Therefore a comprehensive study on the acoustic noise aspects of induction motor drive is required. The acoustic noise study of the motor drive poses multifaceted challenges. A simple motor model is sufficient for calculation of total harmonic distortion (THD). A more detailed model is required for torque pulsation studies. But the motor acoustic noise is affected by many other factors such as stator winding distribution, space harmonics, geometry of stator and rotor slots, motor irregularities, structural issues controlling the resonant frequency and environmental factors. Hence an accurate model for acoustic noise would have to be very detailed and would span different domains such as electromagnetic fields, structural engineering, vibration and acoustics. Motor designers employ such detailed models along with details of the materials used and geometry to predict the acoustic noise that would be emitted by a motor and also to design a low-noise motor. However such detailed motor model for acoustic noise purposes and the necessary material and constructional details of the motor are usually not available to the user. Also, certain factors influencing the acoustic noise change due to wear and tear during the operational life of the motor. Hence this thesis takes up an experimental approach to study the acoustic noise performance of an inverter-fed induction motor at any stage of its operating life. A 10 kVA insulated gate bipolar transistor (IGBT) based inverter is built to feed the induction motor; a 6 kW and 2.3 kW induction motors are used as experimental motors. A low-cost acoustic noise measurement system is also developed as per relevant standards for measurement and spectral analysis of the acoustic noise emitted. For each PWM scheme, the current and acoustic noise measurements are carried out extensively at different carrier frequencies over a range of fundamental frequencies. The main cause of acoustic noise of electromagnetic origin is the stator core vibration, which is caused by the interaction of air-gap fluxes produced by fundamental current and harmonic currents. In this thesis, an experimental procedure is suggested for the acoustic noise characterization of an induction motor inclusive of determination of resonant frequencies. Further, based on current and acoustic noise measurements, a vibration model is proposed for the stator structure. This model is used to predict the acoustic noise pertaining to time harmonic currents with reasonable accuracy. Literature on motor acoustic noise mainly focuses on sinusoidal PWM (SPWM), conventional space vector PWM (CSVPWM) and random PWM (RPWM). In this thesis, acoustic noise pertaining to two bus-clamping PWM (BCPWM) schemes and an advanced bus-clamping PWM (ABCPWM) scheme is investigated. BCPWM schemes are mainly used to reduce the switching loss of the inverter by clamping any of the three phases to DC rail for 120◦ duration of the fundamental cycle. Experimental results show that these BCPWM schemes reduce the amplitude of the tonal component of noise at the carrier frequency, compared to CSVPWM. Experimental results with ABCPWM show that the overall acoustic noise produced by the motor drive is reduced at low and medium speeds if the switching frequency is above 3 kHz. Certain spread in the frequency spectrum of noise is also seen with both BCPWM and ABCPWM. To spread the acoustic noise spectrum further, many variable-frequency PWM schemes have been suggested by researchers. But these schemes, by and large, increase the current total harmonic distortion (THD) compared to CSVPWM. Thus, a novel variable-frequency PWM (VFPWM) method is proposed, which offers reduced current THD in addition to uniformly spread noise spectrum. Experimental results also show spread in the acoustic noise spectrum and reduction in the dominant noise components with the proposed VFPWM. Also, the current THD is reduced at high speeds of the motor drive with the proposed method.