This dissertation presents a new technique for miniaturization of printed RF circuits and antennas. The technique is based on lumped circuit elements and volumetric reactive pin loadings. The vertical arrangement of the pins is shown to provide a meandered current path within the device volume enhancing the miniaturization achieved with sole application of lumped circuit components. The technique is applied for antenna and filter size reduction. In antenna applications, it is shown that due to the presence of the reactive pin loading the overall size of a printed antenna can be miniaturized without affecting the radiation efficiency performance. One of the major advantages of this approach over the existing miniaturization techniques is that it allows reducing the overall size of the antenna (i.e. the substrate size) in addition to its metallization footprint area. Specifically, three antenna designs are presented for GPS and ISM applications. Firstly, a miniaturized wide-band CDL antenna has been introduced. The antenna consists of two loops which are loaded with lumped inductors and coupling capacitors. The design is shown to exhibits 49% smaller footprint size as compared to a traditional patch antenna without degrading the bandwidth performance. Secondly, a circular polarized compact dual-band CDL GPS antenna loaded with lumped capacitors and vertical pins is shown. The antenna operates with >50% lesser area as compared to a traditional L2 patch antenna without degrading its radiation performance. Thirdly, a patch antenna with its cavity loaded with CSRRs is presented. The novelty of the design is that it provides circularly symmetric arrangement of CSRRs thereby enabling the antenna to exhibit circular polarization (CP). Apart from CSRR, further size reduction is obtained by simultaneously reducing the substrate size and ground plane metallization around the CSRRs and loading it with pins. The antenna is 44% smaller than a traditional patch antenna without causing degradation in the antenna's radiation efficiency performance. To extend the volumetric loading to filter applications, the last chapter of the dissertation presents a detailed analysis to understand how geometrical factors (e.g. periodicity, radius, width of the host transmission line, etc) affect the miniaturization performance and quality factor. As a design example, a 2GHz pin loaded hairline filter with 17% -3dB |S21| bandwidth and 1.5dB insertion loss is demonstrated. The footprint size of the filter is ~λ0/16×λ0/9 @ 2GHz and is 45% smaller than its traditional counterpart.

Neste trabalho avaliou-se o desempenho de um reator anaeróbio operado em batelada seqüencial e contendo biomassa imobilizada (ASBBR) em espuma de poliuretano quando submetido a diferentes tempos de alimentação e cargas orgânicas volumétricas, além da aplicação de cargas de choque orgânicas. O reator, com mistura por recirculação da fase líquida e mantido à 30 ± 1 ºC, tratou soro de queijo reconstituído e possuiu 2,5 L de volume reacional. Os resultados mostraram que o tempo de alimentação utilizado exerceu maior influência sobre o desempenho do reator para maiores valores de carga orgânica volumétrica. Durante a operação com carga orgânica volumétrica de 3 gDQO/L.d, a alteração do tempo de alimentação não influenciou na eficiência de remoção de matéria orgânica filtrada, que foi de 98%. Sob carregamento orgânico volumétrico de 6 gDQO/L.d, verificou-se tendência de queda daquela variável para maiores tempos de enchimento: 99, 98 e 97%, para tempos de alimentação de 2, 4 e 6 horas, respectivamente. Na operação com carga orgânica volumétrica de 12 gDQO/L.d, o aumento do tempo de alimentação resultou em queda mais significativa da eficiência de remoção de matéria orgânica filtrada: 97, 95 e 93%, para tempos de alimentação de 2, 4 e 6 horas, respectivamente. Em todas as condições, a aplicação de cargas de choque de 24 gDQO/L.d causaram o aumento da concentração de ácidos no efluente. No entanto, apesar desse aumento, o reator retomou rapidamente sua estabilidade, sendo a alcalinidade otimizada ao afluente suficiente para manter o pH próximo do neutro durante toda a operação. Independente da carga orgânica volumétrica aplicada, a operação com tempo de alimentação de 2 horas foi aquela que proporcionou maior estabilidade e menor suscetibilidade do processo às cargas de choque orgânicas. / This work assessed the performance of an anaerobic sequencing batch reactor containing immobilized biomass (ASBBR) on polyurethane foam when submitted to different feeding times, volumetric loading rate and organic shock loads. The reactor, in which mixing occurred by recirculating the liquid phase, contained 2,5 L reaction medium and was maintained at 30 ± 1 ºC for treating reconstituted cheese whey. Results showed that the effect of feeding time on reactor performance was more pronounced at higher volumetric loading rates. During operation at volumetric loading rate of 3 gDQO/L.d, changing feeding time did not affect filtered organic matter removal efficiency, which amounted to 98%. At volumetric loading rate of 6 gDQO/L.d, removal efficiency showed a tendency to drop at higher feeding times: 99, 98 and 97%, for feeding times of 2, 4 and 6 hours, respectively. At volumetric loading rate of 12 gDQO/L.d, increase in feeding time resulted in a more significant drop in filtered organic matter removal efficiency: 97, 95 and 93%, for feeding times of 2, 4 and 6 hours, respectively. Application of shock loads of 24 gDQO/L.d caused increase in acids concentration in the effluent, at all conditions. However, despite this increase, the reactor readily regained stability and optimized alkalinity supplementation to the influent was sufficient to maintain near neutral pH during the entire operation. Regardless of applied volumetric loading, operation with feeding time of 2 hours was which yielded maximum stability and reduced susceptibility of the process to organic shock loads.

Neste trabalho avaliou-se o desempenho de um reator anaeróbio operado em batelada seqüencial e contendo biomassa imobilizada (ASBBR) em espuma de poliuretano quando submetido a diferentes tempos de alimentação e cargas orgânicas volumétricas, além da aplicação de cargas de choque orgânicas. O reator, com mistura por recirculação da fase líquida e mantido à 30 ± 1 ºC, tratou soro de queijo reconstituído e possuiu 2,5 L de volume reacional. Os resultados mostraram que o tempo de alimentação utilizado exerceu maior influência sobre o desempenho do reator para maiores valores de carga orgânica volumétrica. Durante a operação com carga orgânica volumétrica de 3 gDQO/L.d, a alteração do tempo de alimentação não influenciou na eficiência de remoção de matéria orgânica filtrada, que foi de 98%. Sob carregamento orgânico volumétrico de 6 gDQO/L.d, verificou-se tendência de queda daquela variável para maiores tempos de enchimento: 99, 98 e 97%, para tempos de alimentação de 2, 4 e 6 horas, respectivamente. Na operação com carga orgânica volumétrica de 12 gDQO/L.d, o aumento do tempo de alimentação resultou em queda mais significativa da eficiência de remoção de matéria orgânica filtrada: 97, 95 e 93%, para tempos de alimentação de 2, 4 e 6 horas, respectivamente. Em todas as condições, a aplicação de cargas de choque de 24 gDQO/L.d causaram o aumento da concentração de ácidos no efluente. No entanto, apesar desse aumento, o reator retomou rapidamente sua estabilidade, sendo a alcalinidade otimizada ao afluente suficiente para manter o pH próximo do neutro durante toda a operação. Independente da carga orgânica volumétrica aplicada, a operação com tempo de alimentação de 2 horas foi aquela que proporcionou maior estabilidade e menor suscetibilidade do processo às cargas de choque orgânicas. / This work assessed the performance of an anaerobic sequencing batch reactor containing immobilized biomass (ASBBR) on polyurethane foam when submitted to different feeding times, volumetric loading rate and organic shock loads. The reactor, in which mixing occurred by recirculating the liquid phase, contained 2,5 L reaction medium and was maintained at 30 ± 1 ºC for treating reconstituted cheese whey. Results showed that the effect of feeding time on reactor performance was more pronounced at higher volumetric loading rates. During operation at volumetric loading rate of 3 gDQO/L.d, changing feeding time did not affect filtered organic matter removal efficiency, which amounted to 98%. At volumetric loading rate of 6 gDQO/L.d, removal efficiency showed a tendency to drop at higher feeding times: 99, 98 and 97%, for feeding times of 2, 4 and 6 hours, respectively. At volumetric loading rate of 12 gDQO/L.d, increase in feeding time resulted in a more significant drop in filtered organic matter removal efficiency: 97, 95 and 93%, for feeding times of 2, 4 and 6 hours, respectively. Application of shock loads of 24 gDQO/L.d caused increase in acids concentration in the effluent, at all conditions. However, despite this increase, the reactor readily regained stability and optimized alkalinity supplementation to the influent was sufficient to maintain near neutral pH during the entire operation. Regardless of applied volumetric loading, operation with feeding time of 2 hours was which yielded maximum stability and reduced susceptibility of the process to organic shock loads.