Vortex generator jets (VGJs) have been found to be an effective method of active separation control on the suction side of a low pressure turbine (LPT) blade at low Reynolds numbers. The flow mechanisms responsible for this control were studied and documented in order to provide a basis for future improvements in LPT design. Data were collected using a stereo PIV system that enabled all three components of velocity to be measured. Steady VGJs were injected into a laminar boundary layer on a flat plate (non-separating boundary layer) in order to more fully understand the characteristics and behavior of the produced vortices. Both normal (injected normal to the wall) and angled (injected at 30° pitch and 90° skew angles to the freestream) jets were studied. The steady jets were found to create vortices that swept the low momentum fluid up from the boundary layer while transporting high momentum freestream fluid towards the wall, a phenomenon that provides the ingredients for flow control. Pulsed VGJs were then injected on a flat plate with an applied adverse pressure gradient equivalent to that experienced by a commonly tested LPT blade. This configuration was used to study the effectiveness of the flow control exhibited by both normal and angled jets on a separating boundary layer. Time averaged results showed similar boundary layer separation reduction for both normal and angled jets; however, individual characteristics suggested that the control mechanism of the two injection angles is distinct. Steady and pulsed VGJs were then applied to a new aggressive LPT blade design to explore the effect of the jets on a separating boundary layer along the curved blade surface. Steady injection provided flow control through freestream entrainment, while pulsed jets created a two-dimensional, spanwise disturbance that reduced the separated area as it traveled downstream. A detailed fluid analysis of the uncontrolled flow around the blade was performed in order to identify the separation and reattachment points and the area of transition. This information was used as a basis for comparison with the VGJ cases to determine flow control effectiveness.

<p>Many flow cases in fluid dynamics face undesirable flow separation due torising static pressure on wall boundaries. This occurs e.g. due to geometry as ina highly curved turbine inlet duct or e.g. on flow control surfaces such as wingtrailing edge flaps within a certain angle of attack range. Here, flow controldevices are often used in order to enhance the flow and delay or even totallyeliminate flow separation. Flow control can e.g. be achieved by using passiveor active vortex generators (VG) that enable momentum mixing in such flows.This thesis focusses on passive VGs, represented by VG vanes that are mountedupright on the surface in wall-bounded flows. They typically have an angle ofincidence to the mean flow and, by that, generate vortex structures that in turnallow for the desired momentum mixing in order to prevent flow separation.A statistical VG model approach, developed by KTH Stockholm and FOI,the Swedish Defence Research Agency, has been evaluated computationally.Such a statistical VG model approach removes the need to build fully resolvedthree-dimensional geometries of VGs in a computational fluid dynamics mesh.Usually, the generation of these fully resolved geometries is rather costly interms of preprocessing and computations. By applying this VG model, thecosts reduce to computations without VG effects included. Nevertheless, theVG model needs to be set up in order to define the modelled VG geometry inan easy and fast preprocessing step. The presented model has shown sensitivityfor parameter variations such as the modelled VG geometry and the VG modellocation in wall-bounded zero pressure gradient and adverse pressure gradientflows on a flat plate, in a diffuser, and on an airfoil with its high-lift systemextracted. It could be proven that the VG model qualitatively describes correcttrends and tendencies for these different applications.</p>

"A flow control method for minimizing losses in a highly loaded compressor blade was analyzed. Passive and active flow control experiments with vortex generator jets were conducted on a seven blade linear compressor cascade to demonstrate the potential application of passive flow control on a highly loaded blade. Passive flow control vortex generator jets use the pressure distribution generated by air flow over the blade profile to drive jets from the pressure side to the suction side. Active flow control was analyzed by pressuring the blade plenum with an auxiliary compressor unit. Active flow control decreased profile losses by approximately 37 % while passive flow control had negligible impact on the profile loss of a highly loaded blade. Passive flow control was able to achieve a jet velocity ratio, jet velocity to upstream velocity, of 0.525. The success of active flow control with a velocity ratio of 0.9 suggests there is potential for passive flow control to be effective. The research presented in this thesis is motivated by the potential savings in the applications of passive flow control in gas turbine axial compressors by increasing the aerodynamic load of each stage. Increased stage loading that is properly controlled can reduce the number of stages required to achieve the desired pressure compression ratio."

The separating turbulent flow in a plane asymmetric diffuser with 8.5 degrees opening angle is investigated experimentally and computationally. The considered flow case is suitable for fundamental studies of separation, separation control and turbulence modelling. The flow case has been studied in a specially designed wind-tunnel under well controlled conditions. The average velocity and fluctuation fields have been mapped out with stereoscopic particle image velocimetry (PIV). Knowledge of all velocity components allows the study of several quantities of interest in turbulence modelling such as the turbulence kinetic energy, the turbulence anisotropy tensor and the turbulence production rate tensor. Pressures are measured through the diffuser. The measured data will form a reference database which can be used for evaluation of turbulence models and other computational investigations. Time-resolved stereoscopic PIV is used in an investigation of turbulence structures in the flow and their temporal evolution. A comparative study is made where the measured turbulence data are used to evaluate an explicit algebraic Reynolds stress turbulence model (EARSM). A discussion regarding the underlying reasons for the discrepancies found between the experimental and the model results is made. A model for investigations of separation suppression by means of vortex generating devices is presented together with results from the model in the plane asymmetric diffuser geometry. A short article on the importance of negative production-rates of turbulent kinetic energy for the reverse flow region in separated flows is presented. A detailed description of the experimental setup and PIV measurement procedures is given in a technical report. / QC 20100923

This thesis presents the results of an experimental study that investigates the effects of steady vortex generator jets (VGJs) integrated to a low pressure turbine blade to control the laminar separation bubble occurring on the suction surface of the blade at low Reynolds numbers. The injection technique involves jets issued from the holes located near the suction peak of the test blade which is in the middle of a five-blade low speed linear cascade facility. Three injection cases are tested with different blowing ratio values ranging from low to high. Surface pressure and particle image velocimetry (PIV) measurements are performed. The results show that steady VGJ is effective in eliminating the laminar separation bubble. Also it is observed that to have fully developed attached boundary layer, blowing ratio should be chosen accordingly since a very thin separation zone still exists at low blowing ratios.

Vortex generator jets (VGJs) have proven to be effective in minimizing the separation losses on low-pressure turbine blades at low Reynolds numbers. Experimental data collected using phase-locked particle image velocimetry and substantiated with a hot-film anemometer were used to answer fundamental questions about the influence of VGJs on a separated boundary layer. The data were collected on the suction surface of the Pack B blade profile, which has a non-reattaching separation bubble beginning at 68% axial chord. Two VGJ pulse histories were created with different frequencies, jet durations, and duty cycles. The mechanisms responsible for boundary layer separation control were shown to be a combination of boundary layer transition and streamwise vortical structures. Jet duration and relaxation time were important VGJ characteristics in determining the extent of control. The unsteady environment characterisitic of the low-pressure turbine section in a gas turbine engine effectively reduces the time-averaged separation zone by as much as 35%. Upstream blade rows create unsteady flow disturbances (wakes) that transition the flow. This transitioned flow propagates downstream, re-attaching the separation bubbles on the subsequent blade row. Phase-locked PIV and hot-film measurements were used to document the characteristics of this separation zone when subjected to synchronized unsteady wakes and VGJs. The phase difference between VGJ actuation and the wake passing, blowing ratio, and VGJ duration were optimized to achieve the greatest time-averaged control of the separation zone. The experimental data were used to identify the important characteristics of the wake/jet interaction. Phase-locked PIV measurements were taken to isolate the wake event (wake only), the VGJ event (jets only), and the synchronized combination of unsteady wakes and jets. The synchronized conditions achieved maximum separation bubble control. The presence of wake and jet induced calmed zones are also noted.

No description available.

No description available.

No description available.

No description available.